Nice! I did my first top end back in 1978 on my ‘78 YZ80 using an article from Dirt Bike magazine and a Photocopy from my Yamaha dealer👍😂 I was 12 years old and was so amazed when it fired up and ran great afterwards! One of the most rewarding moments of my life. Sure wish we had KZbin and videos like this back then!
@brian.d.mobley3 жыл бұрын
Hey Robert!! I know that feeling! I remember my first overall rebuild. I was totally amazed that my motor fired up on the literally the first "kick" (but it was a kart, so the way we started them was more of a bump start). Anyway, it is a great feeling, I agree!! Thanks for watching!
@waylonlegend46032 жыл бұрын
The air cooled are a dream to work on. Well except for the 40 year old seized bolts
@jcaashby32 жыл бұрын
Back in the 80s either you figured it out yourself or you were SOL.
@belindapuddey49122 жыл бұрын
thanks for the video It helped a lot. Oven cleaner ! why didnt I think of that!!
@brian.d.mobley2 жыл бұрын
Hey Belinda! So glad it helped!!! Thanks for watching!
@loganbaker90382 жыл бұрын
Great video…I was just unsure on wether to install a new rc valve assembly, or if cleaning the old one up is fine. Thanks!
@ztr_films Жыл бұрын
Hey Brian! I have an 04 CR125 and it has an A cylinder. When doing a top end rebuild is it important to have an A piston to match the cylinder or is using a B piston also fine?
@brian.d.mobley Жыл бұрын
Hi Jade. So here’s the extent of my knowledge on that. Nona recommends using an A piston with an A cylinder. The reason why..? That I don’t know! The A cylinder is far more common, BTW. Sorry I don’t have more knowledge to share on the subject but I’m sure a little digging on the web should reveal the reasons.
@samikaranoub6843 жыл бұрын
i got a pw80 for my brother is it still the sami steps?
@brian.d.mobley3 жыл бұрын
I’m sure there will be some differences, but they are both 2 strokes. However, the PW80 is air cooled. What I would do is get the service manual AND watch the video. The procedures are likely similar but you can confirm all the steps with the manual.
@AmazingBlaze07 ай бұрын
My piston ring keeps it from going on
@boogiekush93913 жыл бұрын
I've spent 2 fuckin hours so far tryna get my cylinder back on and this guy just dose it like that , I'm working on a kx85 and the piston has 2 rings and it's just gets stuck every time even when I'm pushing the top of the piston in the cylinder it just feels like it's getting caught on the rings , maybe I'm not using enough oil? I've also tried zip ties idk what to do
@brian.d.mobley3 жыл бұрын
Hey Boogie! Maybe take a break first! Its hard to show some things like sliding the cylinder over the piston and installing wrist pin circlips. It takes patience and some practice. Ive been doing it for over 20 years, so that helps. BUT, compress the ring at a point farthest away from the gap and try sliding the piston in about 3 degrees from 90 degrees. So, the piston is tilted ever so slightly higher on the side farthest from the end gap. Get the side without the end gap to slip inside the cylinder, then compress the ring midway between the high part of the piston that should now be in the cylinder and press they cylinder down a bit more. Working on motors is tedious sometimes. I get frustrated too. I have a new video coming out this weekend where I slide a 3 ring piston into a bore. Maybe it will be easier to see how I do it. If you really cant get it done, I can help you by email. You can do it!!
@boogiekush93913 жыл бұрын
@@brian.d.mobley thanks man and I did I can back from my storege unit and at chilled out with my girl and went back and put the whole bike back together, I've noticed when I get like that I need to just step away for a hour or 2 and refresh, appreciate the advice it really helped a lot!
@brian.d.mobley3 жыл бұрын
@@boogiekush9391 I sometimes struggle with frustration too. But, I’m really glad to read that you got it all sorted out and you’re happy again. Mechanics can be very tedious sometimes.
@alexanderdye224 Жыл бұрын
this looked way too easy 😭😭
@brian.d.mobley Жыл бұрын
Hey Alexander! Wellll….. Let’s just say that having the ability to edit out some things does make it seem a whole easier! Ha! Thanks for watching!
@spiffymedia58683 жыл бұрын
Awesome video! I’m a 16 year old gear head that just bought a low compression CR125. Wasn’t 100% sure how to order the right size piston. This helps a ton. Keep the great content coming!
@brian.d.mobley3 жыл бұрын
Thanks Spiffy! Keep wrenching! The world needs more young people with mechanical skills! Thanks for watching!
@ouizLOL3 жыл бұрын
Thank you ive similar bike perfect for me
@brian.d.mobley3 жыл бұрын
Great! I hope my video(s) helped!
@backyardbraaapn10173 жыл бұрын
EXCELLENT video. Thank you for this
@brian.d.mobley3 жыл бұрын
Glad it was useful for you! Thanks for watching.
@chrisbilling10 ай бұрын
Man you really helped me out. Finishing up my rebuild on my cr125 and the level of detail in this vid was so helpful
@brian.d.mobley10 ай бұрын
So glad it helped! Thanks so much for watching!
@scottbuck93484 жыл бұрын
OMG the timing of this video could not be better. I just bought a 1997 CR 125 and I’m going to rebuild the top end, I’m definitely going to save this video. I have a question, I’m planning on ordering a top end kit but I’m wondering what year Honda started stamping the cylinders with A and Bs. I read it was either 2000 or 2002 so I do not have to worry about mine being a 1997 correct?
@scottbuck93484 жыл бұрын
Also do u absolutely have to remove the flapper valves and flapper valve shaft when just swapping the piston ring and gasket? I’ve rebuilt my little nitro engines on my rRemote Control helicopters but obviously never had to mess with power valves or anything. You have no idea how big of help you are, Greatly appreciate it and you got a life long scriber here!!!
@brian.d.mobley4 жыл бұрын
Hey Scott! Honestly, Im not sure of the year that Honda started designating cylinders as A or B, BUT in 1997 that naming convention was being used. So, you have either and A or B cylinder and it should be marked on the rearward facing, left side of the cylinder very near the rearward most cylinder bolt. I would recommend getting the corresponding piston that matches your cylinder type. Often, non OEM piston manufacturers only sell an A piston, so if you don’t go OEM, you may have limited choices. There are far more A cylinders out there than B, so odds are that you are fine with an aftermarket A piston sold by someone other than Honda.
@brian.d.mobley4 жыл бұрын
@@scottbuck9348 Regarding the flapper valve service, its a free country, so you don’t have to! But, its not hard to do and it gets harder and harder to get them out and clean them the longer you wait. Its really not a hard job and it makes a noticeable difference in performance when they are clean and working right. I’d just suck it up and do it since you have the cylinder out. And THANK YOU for the comments and for subscribing! Ive become obsessed with videography and editing so Im glad I was able to help someone with one of my video projects!
@scottbuck93484 жыл бұрын
Awesome thank you for clearing that up, I will take your device . Much appreciated
@techdeckdude3443 жыл бұрын
@@brian.d.mobley this was so helpful as i have never rebuilt my 2-stroke before.
@jakehauss72343 жыл бұрын
Do you not have to measure the bore and width of the piston?
@brian.d.mobley3 жыл бұрын
Hi Jake. If you are using a matched piston and cylinder, you really dont need to measure the piston. For instance, on a Honda, if you have an "A" cylinder and install and "A" piston, you are good to go. But, I did go over measuring pretty extensively in this video if you need all the details: kzbin.info/www/bejne/eGiZqKh6lsaiatk
@cameronjames98397 ай бұрын
What is a recommended top end rebuild kit i should get for my 02 cr125?
@brian.d.mobley7 ай бұрын
Honestly, I’d recommend skipping any kit and just buy OEM replacement parts from the manufacturer. There aren’t many parts to buy and you can trust the factory quality. I don’t buy kits anymore.
@techdeckdude3443 жыл бұрын
Hey Brian, as i am just about to start this exact job on my 1998 cr125, how did you remove the fuel tank without having to drain the fuel?
@brian.d.mobley3 жыл бұрын
Hey YLWR6! All you have to do is turn the petcock to the off position. I know it sounds overly simple, but thats it. It may drip a wee bit of gas, but not much. If you get stuck or need help, dont hesitate to reach out.
@rollinrowley86813 жыл бұрын
thanks for the vid man it helped a lot
@brian.d.mobley3 жыл бұрын
Hey Kevin! So glad it helped! I had fun making that video. Got a new camera which helped to make the image quality better too. Thanks for the taking the time to share your experience with the video.
@davemccage791810 ай бұрын
That is the cleanest garage I’ve ever seen in my life.
@brian.d.mobley10 ай бұрын
Haha! Yeah, it’s pretty nice in the shop, but I spend a lot of time out there so I want it clean and nice.
@davemccage791810 ай бұрын
@@brian.d.mobley I’m jealous. My garage goes from being decent to looking like a hurricane hit it when I’m wrenching on something. Excellent video btw! I’m about to tackle on top end rebuild on an RM 80 so this helps a lot!
@brian.d.mobley10 ай бұрын
@@davemccage7918 Mine gets messy sometimes too. But I try to at least put my tools back after I’m done with them so at least those stay organized. But it’s hard to always keep everything tidy, so I feel ya! Good luck on the Yamaha!
@aussiedigger1441 Жыл бұрын
Is it normal to have alot of piston movements at TDC? I have new topend bearing & big end. I'm Using old piston and rings because my cylinder needs service and didn't want to hone & new rings. Unfortunately I didn't notice any of the movements from piston at tdc.
@brian.d.mobley Жыл бұрын
Hey Aussie. In a word, no. But you can measure the outside diameter of your piston and the inside dimension of the cylinder to make sure all are within the manufacturers specs.
@aussiedigger1441 Жыл бұрын
Ok thanks mate, just to be safe I think i will check. At the very top of sleeve I can see a uneven line where the new factory nicseal is & the worn nicseal. I was thinking that is because of piston rocking?
@jonathanrockstar12 жыл бұрын
This was one of the best mechanical videos I’ve ever seen. Thank you for the time and effort you out into this!
@brian.d.mobley2 жыл бұрын
Oh man! Thanks Jrob! Glad you found it useful!
@brennanwatson53393 ай бұрын
Will this video work for my 2003 cr125
@brian.d.mobley3 ай бұрын
It’s essentially the same procedure but the engine featured in this video is a 2007. Best practice is to supplement your knowledge base with the factory service manual.
@757machinist16 күн бұрын
@15:36 why not just use a crow's foot and do the math for the torque? just wondering since i'm about to do my first top end.
@brian.d.mobley16 күн бұрын
@@757machinist I’m not familiar with a crows foot. But if you feel you can do it differently and get the same torque spec, feel free!
@757machinist16 күн бұрын
@@brian.d.mobley gotcha just figured I’d ask! Thanks for the quick response!
@brian.d.mobley16 күн бұрын
@@757machinist Absolutely! Have fun on your top end job.
@NebzyBaby3 жыл бұрын
Hey I have a 2003 cr125 and it runs good no bog or anything and it will rev out but I feel like (I know) it’s not as snappy or fast as it should be I think my power valves are having problems any idea what could be my problem? Just did top end, new lectron carb also. Cylinder is brand new.
@brian.d.mobley3 жыл бұрын
Hi ONebulaz! Like a lot of problems, there can be many reasons. If the power valves are not clean, they can affect performance. I have had such poor luck and spend so much time trying to help people analyze their problems that I just find its basically useless unless I have the motor in front of me, its almost impossible to say.
@5thgearedlined Жыл бұрын
I used ur video and got my 125 fired up, thing hasn’t ran in 10 years 😂
@brian.d.mobley Жыл бұрын
How cool! I’m stoked! I love to know my video helped someone! Thanks for watching.
@5thgearedlined Жыл бұрын
@@brian.d.mobley heck yeah, I watched it step by step. It was pretty fun resurrecting my Honda
@lukasroyster66312 жыл бұрын
I have a 2003 cr125 and my jug doesn’t have 2 opening sides. I only have the side the power valve slides into.
@danshealthylifestyle84434 жыл бұрын
Great video man love the details
@brian.d.mobley3 жыл бұрын
Glad you liked it!!
@burstable252Ай бұрын
do i have to use a torque wrench and if i don't what could happen
@brian.d.mobleyАй бұрын
@@burstable252 It’s a free country, so you don’t have to. I’ll just say that if you don’t want to do the job as recommended by the manufacturer, you’re risking the reliability of your repair.
@burstable252Ай бұрын
@@brian.d.mobley oh ok thanks
@chrisbilling11 ай бұрын
What are your thoughts on honing the cylinder?
@brian.d.mobley11 ай бұрын
Hi Chris. A ball honing using a hone made for the ID of the cylinder is a good idea. Be sure to THOROUGHLY clean the cylinder after the procedure. Good question.
@wrxd12472 жыл бұрын
do you spray it with oven spray and then put it in the oven?
@brian.d.mobley2 жыл бұрын
I didn’t, but you probably could provided the heat introduced was not excessive.
@kingmidas3933 жыл бұрын
Hey Brian I got a 2000 cr250 and it has coolant leaking into my top end any suggestions on this? Thanks
@brian.d.mobley3 жыл бұрын
Hi King! Yes. The most likely culprit is a defective cylinder or head gasket.
@BlueBandit-b3s Жыл бұрын
FS on piston = forged steel maybe ??
@brian.d.mobley Жыл бұрын
Maybe! Good thought!
@liamtofte17093 жыл бұрын
Rebuilding my top end on my 1999 Cr this should help heaps
@brian.d.mobley3 жыл бұрын
I hope it does! The top end is different on the 99, but I’m sure you can figure it out if you have a service manual. Thanks for watching!
@s4ml0ck543 жыл бұрын
Man this really saved me! Thank you💪🏼💪🏼
@brian.d.mobley3 жыл бұрын
Hey S4! I’m so glad! It’s awesome to know I can help someone.
@larryjr5587 ай бұрын
thanks for the great video just got my hands on an 02 cr125r and the carb is leaky and clogged and the top end needs urgent rebuilding! i’m new to riding but i love it so much and i want to start wrenching on the bike! bought tons of tools for the bike and the proper manual and other stuff im eager to start and vids like these help a ton! thanks a lot!
@brian.d.mobley7 ай бұрын
Congrats on the bike and hats off to you for deciding to work on the bike yourself. It’s a lot of fun and very satisfying working on mechanical things!
@LDPoficial Жыл бұрын
thank you for your videos!! amazin
@brian.d.mobley Жыл бұрын
My pleasure! Thanks for the kind words!
@leviharris9002 ай бұрын
My head has a little scoring on it, is it still okay to re use
@brian.d.mobley2 ай бұрын
It’s really not possible for me to say without having the head in my possession for evaluation. If you’re unsure, take it to a motorcycle dealership and have it evaluated by an experienced mechanic.
@leviharris9002 ай бұрын
@brian.d.mobley thanks for the reply, great video
@brian.d.mobley2 ай бұрын
@@leviharris900 So glad you found it useful! Thanks for watching.
@e.l.95899 ай бұрын
Is rebuilding it on a 1983 worth it?
@brian.d.mobley9 ай бұрын
That is a personal decision. If you enjoy the work, do it!
@e.l.95899 ай бұрын
@@brian.d.mobley There's an 83 for $500, but afraid of not finding newer parts.
@eddieramirez6682 жыл бұрын
Hello , what would be the minimum compression it should have ? I just bought a 2006 Honda cr125r and it won't turn on . I did a compression test an it shows it has 120psi.
@brian.d.mobley2 жыл бұрын
Hey Eddie. Off the top of my head, I don’t recall. Do you have the service manual? If not, I can email one to you in PDF. All that good info is in the manual. If you don’t have it, you need it!
@joshpresley48182 жыл бұрын
What brand piston did you use?
@brian.d.mobley2 жыл бұрын
Hi Josh! I used a Honda OEM piston.
@eliriley617911 ай бұрын
Perfect demonstration. I have never rebuilt any engine and usually when i need help with something for my bike i gotta watch a million videos and look in the manual but you sir got it all in one and it only took me 2-1/2 hours to rebuild my top end purely based off this video.
@brian.d.mobley11 ай бұрын
That makes me so happy to read! My main desire with this channel is to encourage people to trust themselves and simply try! So glad it helped you.
@gustavoavina31362 жыл бұрын
Great video! One question. Do 1994 Honda CR125R 2 stroke have timing? I removed my kick starter because the spring broke and the piston moved. My concern is that make be it needs to be timed. I might be wrong, but wanted to ask you. I appreciate it 👍
@brian.d.mobley2 жыл бұрын
Hi Gustavo. Replacing the broken spring on your kickstart lever will not be adversely affected by the movement of your piston. Good luck on your repair. Thanks for watching!
@gustavoavina31362 жыл бұрын
@@brian.d.mobley thank you very much 👍
@kenweis7913 Жыл бұрын
Good tips good build
@brian.d.mobley Жыл бұрын
Thanks Ken! More videos coming soon! Thanks for watching.
@jonathanrockstar12 жыл бұрын
Did you replace any of the shiny looking nuts on the head and the place where the cylinder meets the crankcase, like the four studs? I’m trying to find replacement flange nuts and they all have serrations on the bottom from what I can find. I’m kind of against using a nut and washer to replace them considering how the original parts were flange nuts. Any help is appreciated!
@brian.d.mobley2 жыл бұрын
Hey Jrob. I did replace the studs and the nuts. I got all the OEM parts from Rocky Mountain ATV. I don’t recall if the OEM nuts were serrated on the underside of the flange, however. Thanks for watching!!
@jonathanrockstar12 жыл бұрын
@@brian.d.mobley thanks!
@Peter-Benson-Music2 жыл бұрын
Does this apply for 1993 125?
@brian.d.mobley2 жыл бұрын
Hi Peter! Generally speaking, yes. But every bike uses somewhat different components. But the general procedure is the same.
@Peter-Benson-Music2 жыл бұрын
@@brian.d.mobley perfect thank you much, appreciate the quick response
@brian.d.mobley2 жыл бұрын
@@Peter-Benson-Music Glad to help! Keep wrenching!
@thegriffin84163 жыл бұрын
I dont even own a CR but that was a great video,
@brian.d.mobley3 жыл бұрын
Haha! Hey Griffin! Well, the moral of that story is that you need to go buy one now!
@chrisbilling11 ай бұрын
This is one of the greatest and most thorough 2 stroke rebuild videos ive seen. Thank you
@brian.d.mobley11 ай бұрын
Thanks so much Chris!
@AmazingBlaze07 ай бұрын
About to attempt my first Top end Rebuild on my 03 Cr125r ofc I bought it looked nice ran pretty good but ofc I took it apart the piston looks fried, cylinder wall looks fine, carb needs rebuild, I’m doing that and the Jetting…. She outa be a rippa when I’m done and honestly I can say I’m proud that I’ve gotten as far as I have, thanks man I’m 17 and need to know this!!!!
@brian.d.mobley7 ай бұрын
That warms my heart to read that young guys like you still want to learn to use your hands and actually create something. The MAIN reason I started this channel was to pass on what I’ve learned in the hope that the younger generation might learn and benefit. Keep wrenchin’!
@AmazingBlaze07 ай бұрын
@@brian.d.mobleythanks again all I’m waiting on are my parts to come in and I’m ready to go!!
@AmazingBlaze07 ай бұрын
@@brian.d.mobleyhey man I got my bike going big thanks to you I’m so happy it started up and ran better than before, almost like the feeling of working on it more than riding it🤣💯💯
@brian.d.mobley7 ай бұрын
@@AmazingBlaze0 Fantastic!!! That’s great! Great feeling to do it yourself too!
@lorijones8156 Жыл бұрын
great video
@brian.d.mobley Жыл бұрын
Thanks! Sorry I missed this comment! Thanks for watching!
@billf47143 жыл бұрын
Do you have a parts list by any chance? Any specialty tools you think would be helpful? I’m going to attempt this for the first time and was wondering. Thanks!
@brian.d.mobley3 жыл бұрын
Hey Bill! The parts needed are really dependent on the year model and make of your bike. If you dont have the factory service manual for your bike, that should be step one. If you haven’t purchased the parts yet, contact a company like Rocky Mountain ATV or Motosport and just ask someone in their sales department whats needed for you specific bike. As for special tools, the only one is a torque wrench. If you get stuck, message again and I’ll help you through it.
@billf47143 жыл бұрын
@@brian.d.mobley Thank you!
@stephenwalsh81849 ай бұрын
🏍👍
@brian.d.mobley9 ай бұрын
Thanks!
@LSmoney2153 жыл бұрын
Thanks for uploading this video. Save me a lot of money
@brian.d.mobley3 жыл бұрын
Hey Lindon! That is what keeps me going - knowing I can help other people! Thanks for watching!
@speeddemon95553 ай бұрын
great post, but, i wanted to hear it running.
@brian.d.mobley3 ай бұрын
✌🏻
@drpacman99962 жыл бұрын
If the piston is seized in the barrel (maybe broken ring) what the best way to minimise the damage when taking it off? I'm thinking ill have to take the head off and use the kick start to get the piston as low in the barrel as possible then tap on the piston whilst lifting the barrel?
@brian.d.mobley2 жыл бұрын
Hey Dr. Paca. I don’t know if a good way to do the procedure about which you are inquiring with the motor still in the chassis. The best way is with the motor out using some sort of press. I’ve used the crank remover press for this purpose. I show the procedure in a more recent video where I disassembled a CRF70 motor. It had a piston in it that had become so corroded with oxidation that it was seized. Hitting the top of the piston with a mallet is not good practice as you can damage the lower end rod bearing and even throw the crank out of balance using blunt force. I wish I had better news.
@drpacman99962 жыл бұрын
@@brian.d.mobley Thanks for the reply Brian. The piston will move with the kick start but scraping a bit, guess some damage to the barrel is unavoidable. I'll avoid hitting the piston as much as possible. Thanks again
@brian.d.mobley2 жыл бұрын
@@drpacman9996 If the piston will move, you have hope. You can probably get the cylinder off. The best way to avoid damage to the cylinder that’s practical for a home mechanic is to try sliding very thin feeler gauges (maybe 3) between the ring and the bore to compress the ring slightly. This could be challenging and time consuming, but with patience, has worked for me. But, I always had the motor out of the chassis.
@drpacman99962 жыл бұрын
@@brian.d.mobley Thanks. I'm not gonna rush anything as the season here is kinda over. I'll try the feeler gauge trick and hopefully be able to hone the barrel rather than re-plate
@stuarthipkins83363 жыл бұрын
Thank you..im about to do mr cr...125
@brian.d.mobley3 жыл бұрын
Thats great Stuart! This on is a 125 also so I hope it shows you exactly what you need! Thanks for watching!
@aderiley65922 жыл бұрын
Great vid! Thanks so much 🙏
@brian.d.mobley2 жыл бұрын
Glad it helped! Thanks for watching!
@growgamer-dz3ul3 жыл бұрын
How do you clean cylinder studs hole?
@brian.d.mobley3 жыл бұрын
Hey Growgamer! I like vapor blasting. But, you can soak them in something like Marvel Mystery Oil or brake cleaner for a day or two and then gently run a tap into the hole.
@foodcritic13993 жыл бұрын
Is there a certain break-in process, after a top end rebuild? Or is it ready to ride full throttle?
@brian.d.mobley3 жыл бұрын
Hi Food Critic. Excellent question! Like a lot of things, there are schools of thought. There are those who support the idea of a break in period such as low to medium revs for 10-15 minutes. Let the motor cool. Ride again for 15 minutes with a couple of full throttle runs in the last few minutes. Let the motor cool. Run it hard for 15 minutes. Let the motor cool. Then retorque the cylinder and head nuts and your good to go. Other suggest that the nikasil cylinder wall is so hard that it doesn’t “seat” with the ring at all so there is no need to observe “break in” procedures. Its hard to argue with the latter, but I just think that taking it slow and doing a few break in cycles can’t hurt and, Honda recommends some type of slow break in period. So, it’s debatable, but I just do it the conservative way. Great question! Thanks for watching!
@foodcritic13993 жыл бұрын
@@brian.d.mobley awesome. Great video and great information. One more question, do you have a video or could you create one accessing, cleaning, adjusting, etc. the carburetor on a Cr125?
@brian.d.mobley3 жыл бұрын
@@foodcritic1399 Hi. I could. It would be a fun one to make also, but I am committed to so many other projects right now that it would be hard to fit that into my schedule. But, I’ll keep it in mind. I’m sure a lot of people would find it useful and it would be fun to make.
@chrisrieger9201 Жыл бұрын
What was the lubes you used?
@brian.d.mobley Жыл бұрын
Hey Chris. I use Maxima. It’s good stuff! I put some links below.
@brian.d.mobley Жыл бұрын
amzn.to/3X7r3v9
@brian.d.mobley Жыл бұрын
amzn.to/3X55E5T
@chrisrieger9201 Жыл бұрын
I didn’t realize the all the technical measurements required for replacing a piston & rings
@brian.d.mobley Жыл бұрын
@@chrisrieger9201 It’s all a function of how deep you want to dive in order to do the job right. It’s possible that employing less precision can still result in a well functioning motor, but you risk more if you don’t take the time to confirm all the dimensions and clearances.
@samikaranoub6843 жыл бұрын
same
@johnjakeup61862 жыл бұрын
I have a question about the valves I had a bore done and seem like my valves keep hitting the top of piston .! When it's bored ? Should they shave the valves too BC that seem not the same size or do I replace the slider valves to the bore size ?
@brian.d.mobley2 жыл бұрын
Hi John: The procedure covered in this video is for 2 stroke motors that do not have valves. Maybe look around for a video on 4 strokes?? Thank you for watching!
@brennanwatson53394 ай бұрын
What year is this bike
@brian.d.mobley4 ай бұрын
2007
@jasonjod1ail4 жыл бұрын
What engine is this ?
@brian.d.mobley4 жыл бұрын
Hey! Its a CR125. 2007 model.
@isaiesquivel17593 жыл бұрын
Goes from 2005-2007 cr125r
@MiguelHernandez-qo2vz3 жыл бұрын
Thank you so much man, im 14 and been buying and fixing bikes and now im able to do alot more
@brian.d.mobley3 жыл бұрын
Hey Miguel! That is awesome. I started out working on mechanical things at around age 8. I started by pulling bicycles out of a bayou nearby that had probably been stolen and trashed! I took them all apart, cleaned them, painted them and rebuilt them. I sold a lot of them too. I love to work with my hands and I love to learn new things. Stay curious and stay with it!
@isaiesquivel17593 жыл бұрын
Hey! I’m also 14 brooo
@brian.d.mobley3 жыл бұрын
@@isaiesquivel1759 You young guys are fortunate to be able to have cool bikes at a young age. That’s really great.
@lilwhitec43 жыл бұрын
Awesome thank you
@brian.d.mobley3 жыл бұрын
Glad to help! Thank you for watching.
@briandeal2672 жыл бұрын
Nice!!! Thanks
@brian.d.mobley2 жыл бұрын
Hey Brian! Glad you found it useful!
@marcuscavalier3243 жыл бұрын
i have a '99 cr80R. can i follow these exact steps?
@brian.d.mobley3 жыл бұрын
Hey Marcus! The procedure is basically the same, but the CR80 doesnt have a power valve. I also have a couple of videos on how to Teardown and Rebuild a CR85 motor. You can alway look there too. But, basically, the procedures are the same on the CR80 and the CR125.
@marcuscavalier3243 жыл бұрын
@@brian.d.mobley ah got it! i’ll check out the other vids as well. Thanks!
@brian.d.mobley3 жыл бұрын
@@marcuscavalier324 If you get stuck, just send me a message. Ill do what I can to help.
@marcuscavalier3243 жыл бұрын
Pretty soon will be my first time tackling a top end rebuild. Thanks for being there if i need to reach out
@brian.d.mobley3 жыл бұрын
@@marcuscavalier324 Its really not very hard. Just take your time and make sure you don’t skip a step.
@riskipurnomo3 жыл бұрын
Mantap
@brian.d.mobley3 жыл бұрын
I hope mantap is a good thing!
@riskipurnomo3 жыл бұрын
@@brian.d.mobley of course its mean good job
@brian.d.mobley3 жыл бұрын
@@riskipurnomo Thanks for the kind comment! What language is that? Where do you live?
@riskipurnomo3 жыл бұрын
@@brian.d.mobley ur wellcome, its indonesian language i am from indonesia
@brian.d.mobley3 жыл бұрын
@@riskipurnomo Surprisingly, I get a lot of views from Indonesia. I guess motorcycles are popular there. Great surfing in Indonesia!
@ashtonross53762 жыл бұрын
How much play should be in the rod and piston? Or should there be any at all? I just took apart my 2001 cr125 and can’t find anything wrong besides that, but it makes a horrible top end noise when runnng
@ashtonross53762 жыл бұрын
There is a lot of side to side play where the wrist pin connects
@brian.d.mobley2 жыл бұрын
HI Ashton. There should not be a lot of lateral runout on a wrist pin. The service manual will specify the range. I doubt this is the cause of the noise though. Without having the motor in front of me, its really hard to diagnose problems with motors, however.
@ashtonross53762 жыл бұрын
@@brian.d.mobley ya I looked a t it some more and the crank bearing is shot I won’t know what all else needs replaced till I get a case puller in. Thank you tho video help out a ton
@brian.d.mobley2 жыл бұрын
@@ashtonross5376 Its fun to split the cases and dig in there! If you havent already purchased a splitter, this is the one I use and its been great: amzn.to/3jNTDzs
@davidshears14492 жыл бұрын
Nice!👍
@jake.debnam243 жыл бұрын
I have a 2004 Honda Cr 125 and I was wondering if it will be the same to your 2007 if I rebuild my top end? Also, my 125 has not been running good and to be honest, I’m not that smart mechanically. It keeps fouling plugs with the plugs being black with carbon buildup and once I replace it, it runs for maybe 20 minutes at most and then is fouled again. I run 50:1 from that’s what the guy that sold it to me told me he runs. I live in Alaska and I’m not necessarily going to race but just learn how to ride a 2 stroke for the first time. He also said that he recently rebuilt the top end but I can push the kickstart lever all the way down with my hand, and there is some resistance but not a ton. So after telling you all that, what do you is wrong with it but just reading all that, and what is your advice to how to start to fix it? Please reply if you can, I could really use the help. This video is awesome!! 🤘✌️
@brian.d.mobley3 жыл бұрын
Hey Jake! The 04 is very similar with the exception of the RC Valve being servo driven. (I did another vid on the RC valve if you need it). Plug fouling is usually due to using the wrong plug and/or wrong jets. Check your owners manual for those. That kickstart sounds normal. I can cycle all mine by hand also. One think I DO NOT recommend is running a ratio of 50:1. The factory recommends 32:1 and I’ve been running that for decades. Ratios are hotly debated, but you won’t lose performance by using 32:1 and you will do a lot to ensure the longevity of your motor.