Fix Check Engine Light VSC TRAC OFF for FREE for all vehicles - Guaranteed fix

[@warrenthomas1253]

You would of made a excellent old school teacher. I say old school because they would of came up with their own curriculum and not just be a programmed robot playing a recording. It's rare to be knowledgeable about a subject and to be able to teach it. The old saying people in the top of their profession practice that profesion, and the people who can't compete teach..

[@DocMackGarage]

Thanks alot it really means a lot to me when people appreciate my work. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support.

[@michaelkouloumbis6863]

I'm a retired mechanic, and this morning when I started my 2005 Toyota I saw the VSC TRAC and Check Eng lite on. I didn't have time to check it, but later on I was checking Google as to what the VSC system involves, and came across your video. I never thought that a emission failure would cause the VSC light to also come on. At this point I'm guessing the attendant at the gas station left the cap loose yesterday. Hopefully this is the problem, I'll check it when I get back to the car. Great video.👍

[@DocMackGarage]

Thank you for the comment 😊. Please consider subscribing to my KZbin channel for free if you haven't already.

[@mamandapanda185]

Is that what it was?

[@michaelkouloumbis6863]

@mamandapanda185 No, it wasn't a loose cap. I scanned it, and it only set C1201, which happened once before when I let the fuel level run very low. I cleared it as before, and I hasn't come back.

[@mamandapanda185]

@@michaelkouloumbis6863 Thank you for replying!

[@DocMackGarage]

@mamandapanda185 C1201 sounds more like ECU and multiple things which could cause an MIL to come on . If you get Check Engine + VSC + Trac off it will be what I discussed. In the video I went through several possibilities

[@SamoaLouPele]

Thank you for this. HELPED DIAGNOSE my problem with my Sienna.

[@BornTheDragon]

I'm having pretty much the same issue with my Sienna. Wouldn't open the fuel door so I hit the manual release. When I took the gas cap off there was a lot of pressure in the tank but I put it back on. What did you do to fix yours?

[@jeromemott]

I have a 2005 Lexus RX330. I just had added per Lexus owner's manual dexron III AT fluid to power steering reservoir and the vsc and trac off lights plus a flashing check engine light and rough idle and rough as I drove back home approximately 4 miles. Plus the weather the past 48 hours has been raining with foggy conditions and temps of 40s F - 60 F. And only have approximately 3 gallons of fuel in tank. Thank you in advance for your help and great videos.

[@DocMackGarage]

Hi , Thank you. Did you drain out the fluid first or you topped it up ? If there are air bubbles you will need to open the reservoir and turn the steering all the way to the left and the right till there are no air bubbles. Please consider subscribing to my KZbin Channel for free if you haven't already

[@dapperlygrungy3189]

Thank you for suggesting this video. I commented on another video of yours. I think it might be the Wheel Speed Sensor that's causing the VSC lights to turn ON. I took my car to Pep Boys, a US Franchise Service Center, to replace the Starter. I noticed upon picking my car up, they handed me my wheel lock, so I knew they had to remove the front wheels to replace the Starter. Prior to taking it to Pep Boys, the VSC never came ON. I am taking my car back to Pep Boys tomorrow and have them check the Wheel Speed Sensor. I don't want to spend anymore money on this car. It's 16 yrs old and I am trading it in for a new Toyota Camry. As for the O2 Sensor, I don't see any black smoke. I did test the fuel cap as you suggested in the other video and that didn't work for me.

[@DocMackGarage]

You are welcome. Please remember to subscribe to my KZbin channel of you haven't already.

[@fredmitchel1236]

Not sure why a wheel was removed to get at starter... The starter is located in the V of the 4.7 V8.... I can see a bad wheel sensor giving Trac error

[@CB-hn6pr]

Excellent video, I was not very impressed at the very beginning, but then I realized this is a great video, very very comprehensive. Thanks!

[@DocMackGarage]

@CB-hn6pr Thank you 👍 . Please consider subscribing to my KZbin Channel for free if you haven't already to show your support.

[@SamoaLouPele]

This video 📹 is GREAT!! THANK YOU!! GREAT EXPLANATIONS!! Very DETAILED. VERY thorough!! Going to try ALL these things, although-- from the video--I suspect it is the PURGE VALVE. 🛠

[@DocMackGarage]

You are most welcome. Thank you for the Super Thanks and your appreciation . If you haven't already please consider Subscribing to my KZbin channel to show your support.

[@kishorsshah]

I really liked the way you explained everything. I learned a lot from this. Thanks a lot.

[@DocMackGarage]

@kishorsshah Thank you , please consider subscribing to my KZbin Channel for free if you haven't already to show your support .

[@landosazo7506]

I think you covered all the possible causes...great job, sir

[@DocMackGarage]

Thanks for that. Appreciate it. Please consider subscribing to my KZbin Channel for free if you haven't already.

[@pkybey]

Thank you for saving me a whole lot of fixing.

[@DocMackGarage]

You are most welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support. Also hit the like button if you can 😃

[@Moshishak1]

Thank you for your always thorough explanations of the issues.

[@DocMackGarage]

@Moshishak1 You are most welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support .

[@Jin-ex8bk]

First of all, Great video. I have 2007 Camry V6 with 100,000km. It had been no problem. But last couple weeks ago, VSC check light, tracktion light, and engine check light turned on during driving on the highway. I brought it to my mechanics, and he said nothing bad is scanned. I recently changed the engine airfilter and cabin airfilter by myself. My question is 'Do you think it might cause the problem?'.

[@DocMackGarage]

Hi , thank you. Did you look over the whole video including what I mentioned in the engine bay. Cabin filter would have no effect in these lights , Panel filter there is slight chance you nudged something. Please consider subscribing to my KZbin Channel for free if you haven't already.

[@Jin-ex8bk]

Just subscribed. I just changed the fuel cap. Seems like the engine light has gone away. I will test drive later. I appreciate it.

[@DocMackGarage]

@@Jin-ex8bk You are most welcome 😃

[@klujics123]

Have an ‘08 Sienna XLE. had all these random misfire codes (VSC) and even would have to shut my van down as the “traction control” light would blink along with the engine light causing the van to lose power and decrease in speed, till I shut it off and restarted it. And that would take care of it for a week or so then back again, usually one the Highway. So off to the shoulder again as the van would slowly lose power and buck and gas be basically unresponsive Seems like maybe the compression was changing over the 200,000 miles as i started putting premium gas in and the higher octane was the key.. as all the codes went away (once cleared) and never came back. Same spark plugs. I did change one injector (before I switched to premium gas) as it did have that code come up for the number 2. But the check engine lights would still come on. But same spark plugs on all 6 cylinders as those back are just too hard to change without a good reason. Again premium gas and all my check engine lights and blinking lights are a thing of the past and it’s nice having a dash free of those. (Those lights came on probable a dozen times in the past. But now problem solved for like 9 months now and counting.

[@georgerodriguez4051]

I have the same problem with my 2014 Sienna XLE. I am going to fill with premium hope the problem goes away. Thanks

[@kauaireed9006]

Wow you did the homework! Thanks

[@DocMackGarage]

You are welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support

[@mckoylach1622]

Great,and very elaborate explanations,it’s very helpful,appreciated very much. Today,woke up,go to store,started the car,shook quite drastically,after a minute of running,check engine light and trac off light,came on but the car stopped shaking. Scanned the code,got P0306, misfired. Why is the trac off light,showed,when it’s misfiring ? And is cylinder #6 located on the front side of the engine? Or located toward or next to the firewall? By the way, it’s a 2012 highlander, thanks

[@DocMackGarage]

Thank you. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support. Is it the 2GRFE Engine?

[@vlmrv9108]

Read the codes . When you see C1201 error which means general engine failure. Including misfire. Therefore traction control light on, Toyota reports severe problem with the car , using extra dash light.

[@storyIine]

I wish people with mk3 supras do these types of video so I can understand the systems and components to get it back in the road. Anyway I do have a question regarding a 2008 toyota sienna; when Idle theres a gas smell leaking somewhere, what are common places to look for and to fix the issue regarding the gas leak?

[@DocMackGarage]

@storyIine Charcoal Canister, purge valve, fuel filter, fuel pump, fuel injectors are those I would suggest checking. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support. It would be appreciated.

[@edgarurena9485]

Hi thanks for your video. I recently change my sparkplugs in my Toyota Highlander 2006 V4 and 2 weeks later I got a p0456 with check engine light, trac off and VSC light. What should I do? I already replaced the gas cap and still have the code

[@DocMackGarage]

Hi, there is an emissions leak, if you look through the video I explain in detail other things which can cause the issue. Please subscribe to my KZbin Channel for free if you haven't already.

[@timklein3962]

Great informative video; you cover every base; which most videos don't !!!!!!! 👍👍👍

[@DocMackGarage]

Hi, Thank you. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support.

[@jessyacevedo102]

My problem is that at the same time that light came on for the first time ever my Highlander now does a weird not exactly a shacking per day but kinda like a shack almost like a rocking feeling because of the force that's rotating in the engine or under the car somewhere if this makes any sense. I'll see what's happening

[@DocMackGarage]

Sounds like it is misfiring . Is this the 2GRFE Engine ? Could be camshaft position sensor or plugs and coils . Do a scan and see what comes up. Please consider subscribing to my KZbin Channel for free if you haven't already

[@jodykidd3109]

Nice job partner! Really helpful!

[@DocMackGarage]

You are most welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support. I have lots of car DIY videos

[@ilirkalemi5174]

I got a TRAC off and engine light on yesterday on my 2013 Corolla and the diagnostic gave me a catalytic converter or replace battery( which I replaced 6 months ago). What should I do? Thanks for the video

[@DocMackGarage]

The first thing I would suggest is to get the battery tested, even new batteries can be faulty. If that is OK, did you have see the Check Engine flash?

[@ilirkalemi5174]

The battery tested ok and the check engine light doesn’t flash. Anything else I should check? Thank you for your reply

[@DocMackGarage]

@@ilirkalemi5174 You are welcome, Al's please subscribe to my KZbin channel for free if you haven't already to show your support. Next thing does any black smoke come out the exhaust? Have you verified that the catalytic converter is still there?

[@ilirkalemi5174]

No it’s regular smoke out of the exhaust

[@DocMackGarage]

@@ilirkalemi5174 and you have tried all my suggestions in the video?

[@carmenbrooks7243]

Great explanation. I learning about cars .!

[@DocMackGarage]

You are welcome. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support .

[@carolinaalvarado7523]

First I would like to thank you for your professionalism and easy way of explaining honestly it’s very hard to find someone like you I am a retired female and I can see how they lie and over charge you worst when you’re a female and much worse when you’re older . It would be nice if you put an email to be able to keep in touch Thank you so much for helping us out specially now that life has gotten so expensive and being on a pension 😢

[@DocMackGarage]

Thank you Carolina . Glad I could help 😃 My E-Mail Address is in the about section of my KZbin page. If you haven't alerday Subscribed, please consider subscribing to my KZbin Channel to show your support. I am also of Facebook facebook.com/thedocmackcarchannel . Cheers

[@davidfredricksen5444]

Very helpful. Thanks!

[@DocMackGarage]

@davidfredricksen5444 Thank you, please consider subscribing to my KZbin Channel for free if you haven't already to show your support. It helps show support got the work I do. Cheers 😃

[@sheilatannehill2569]

I am gonna check my fuel cap. Clean it and receptacle as well. Turn car on. If lites still show I'll place saran wrap over the inside of fuel cap, and click it in. Turn car on. If all lites are off then new cap needed. If not will proceed with other areas in your diagram. Already spent hundreds on other stuff including 02 sensor, and I'm going kookoo.

[@DocMackGarage]

Yes it can be a bit of a headache , give the rest of the suggestions a go if this is still an issue. Please make sure to Subscribe to my KZbin Channel.

[@galep2539]

Thank you sir. Very good information and demonstration. 😊

[@DocMackGarage]

Thank you, please consider subscribing to my KZbin Channel for free if you haven't already to show your support in the work I do. 😃

[@karenbearden6198]

Thanks and your diagram was quite helpful.

[@DocMackGarage]

You are most welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support, and also view my other car repair videos 😊

[@happycamper5193]

2011 Toyota Four runner. My brakelight,VSC, 4wd lo, traccontrol is on dash. I checked battery, starter, alternator and gas cap so far.

[@DocMackGarage]

Hi, I have rung through quite a list, so please take a look.

[@daveplem]

Push the brake pedal hard, all the way too the floor. You might have a stuck pressure sensor on the pedal.

[@gto4134]

What if you've done a zero point calibration and the lights goes away for 2-3 weeks but then comes back on? Would that mean a bad steering angle sensor could be a possibility?

[@DocMackGarage]

Yup it could be if the zero point temporarily worked.

[@sylvianyamo1]

Traction control light and check engine light on after fuel pump replacement on my sienna 2016 XLE What could be the problem.

[@samuelyoung9932]

Super educational 👍👍👍👍👍

[@DocMackGarage]

Thank you. 😊 Please consider subscribing to my KZbin Channel for free if you haven't already to show your support.

[@samuelyoung9932]

@@DocMackGarage I already subscribed. Fully support your talents and sharing. ❤️

[@DocMackGarage]

@@samuelyoung9932 Thank you 😊

[@esmail88]

this is great video ..

[@DocMackGarage]

@esmail88 Thank you, please consider subscribing to my KZbin Channel for free if you haven't already to show your support

[@eranomanahan9118]

Thank you. You are one of the best.

[@DocMackGarage]

You are most welcome and thank you for Subscribing

[@carmenbrooks7243]

Thank you. Great lesson

[@DocMackGarage]

You are welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support.

[@xangadixxxx6405]

My corolla Verso Show ABS TRC and VSC off, what can I Check up?

[@DocMackGarage]

Hi, most has been covered in this video. Have a look and I am sure you can resolve it

[@onetruesoldiervt3686]

Hello all my wheel function lights are on Acura DMX 2007 the abs , sh-awd and vcs do you have any suggestions I’d appreciate any feedback since it’s all I can ask of. My check engine is not on though

[@DocMackGarage]

I would suggest checking the ABS module, brake fluid and also fuses. Did you get a wheel alignment done recently?

[@ambrosendyamuba9086]

I have a Toyota crown Majesta V8 model 2009, it tells to check the PCS system, one I was almost getting a head on accident yet it was on but didn't alert in anyway, how can I have it fixed, thanks.

[@DocMackGarage]

I would suggest hooking up a scan tool. Maybe the radar detector is dirty ?

[@SuleimanSabdat-gk5or]

this video is Great what is the name of that diagonis machine

[@HoodsGlobal]

***I got a code p0161 on 2007 Lexus ES350. It refers to heated O2 sensor, bank 2, down stream. Shall I just change the sensor and call it good?

[@DocMackGarage]

@HoodsGlobal Yup those arr one of the things I discussed in the video. You can call it a day once you change it, and clear the lights . Go for a 50 mile drive and if it does not come back , then call it a day. Please Subscribe

[@benstabenny2628]

You are bad to the bone,very helpful info sir

[@DocMackGarage]

Thank you glad it helped. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support . I would really appreciate it.

[@maryjefftheresesison5604]

I don’t know if this is related to your video but I have engine light, tcs light and fcws light on. I notice that every time i press hard on the brakes, tcs and fcws will light up and those will turn off only when i restart the car and don’t press on the brakes as hard as i need to. The engine light just recently turned on so i’m wondering why those two caused the engine light to turn on too.

[@DocMackGarage]

Fcws, is that the forward collision warning system ? Maybe check if the sensor has come loose.

[@portiamachona8259]

Kindly assist,When ever i move from a tarred road to a gravel road i get a check engen light first folowed bt Vsc and track off on my lexus is250.

[@DocMackGarage]

Hi, have you tired my suggestions in the video ? I went through a number of causes. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support.

[@kmontileaux]

Will all three of these lights come on if someone backed into the right rear of my 2011 toyota sienna van? Soft hit, smashed in the bumper, no airbag came on.

[@DocMackGarage]

Highly doubt that would cause it . Try all my suggestions and it might get fixed. If it was a hard hit near the wheel then maybe

[@elink786]

Very good reporting

[@DocMackGarage]

Thank you, please consider subscribing to my KZbin Channel for free if you haven't already to show your support .

[@MarvelousMarkBaptist]

I have a 2005 Toyota Sienna and all 3 dash lights turned on (Check Engine Light, VSC, TRAC OFF). Please help.

[@DocMackGarage]

Hi, have you attempted what I suggested in this video ? Cheers

[@quyenbui7985]

Diconnect negative battery cable for 30 minute and then put it back, start up your engine all 3 lights should go off.

[@DocMackGarage]

@quyenbui7985 It's not that easy my friend , it will go off but then come back soon after . It is one of the suggestions in the video which will fix it

[@quyenbui7985]

@@DocMackGarageit work on my 2004 Toyota 4runner

[@quyenbui7985]

@@DocMackGaragefor two year I don’t see it come back.

[@tyronekim3506]

I have 2007 Camry Hybrid with push button start. The car will not start. The message, "Check VSC SYSTEM", comes on when I try to start. Do I need to have the car towed to a Toyota dealer for repair? Any help will be appreciated. Thank you.

[@DocMackGarage]

Hi, when you press the brake pedal do the brake lights come on ?

[@tyronekim3506]

​@TheDocMackCarChannel Thank you for the reply. I replaced the battery. Things are OK. There's no more message. Thanks again.

[@DocMackGarage]

@tyronekim3506 You are most welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support

[@jitendersonu]

My Toyota Aurion 2007 shows Traction control and abs light with warning light but no engine light. But if I restart the car it goes away and comes back in two days or so. One tool says no fault codes. Can you please guess what can be the issue? Thanks

[@DocMackGarage]

Hi, first thing I would check is the wheel speed sensor , SAS or ABS module. I explain most of this in the video. Are you in AU or NZ ?

[@ashenigunawardana5216]

Hey,, i have question,, I'm from sri lanka i have toyota corolla 2017, traction light on and start stop lock tiar please kindly help me

[@DocMackGarage]

@@ashenigunawardana5216 Hi, locked tyre you said ?

[@ashenigunawardana5216]

@DocMackGarage yers

[@DocMackGarage]

@ashenigunawardana5216 Front or rear ? Does it drag ? Also please consider subscribing to my KZbin Channel for free if you haven't already to show your support

[@daveplem]

Mine was caused by a stuck pressure sensor on the brake pedal. (Part of the ABS system.) I stomped the pedal while already stopped and pushed it all the way to the floor. After a few miles of driving, the lights went off and stayed off.

[@DocMackGarage]

Like a stop lamp switch?

[@laurajanese5371]

Thank you😊

[@DocMackGarage]

You are most welcome, please consider subscribing to my KZbin Channel for free if you haven't already to show your support 😊

[@omulaule1860]

Guys those lights when they appear, replace your front bearings. I di mine this Sunday and disappeared. Am happy now.

[@DocMackGarage]

@omulaule1860 Thank you for sharing, the reasoning behind that is alignment. When you replace a bearing you will need to align hence this would have sorted the lights. Please consider subscribing to my KZbin Channel for free if you haven't already to show your support

[@Baked26]

2010 vibe, throws a c1336 code, i reset the sensor and it goes away. Soon as i start the car and put it in gear the vcs starts flashing and traction control light comes on. Gas cap has been replaced. Where should i start

[@DocMackGarage]

Hi, so the issue is present if not it won't be coming back. I would suggest going through my whole video. Could be wheel speed or steering calibration. I have included this in the video . Please consider subscribing to my KZbin Channel for free if you haven't already.

[@davido3403]

Mine did the same thing and it was the alternator and when the battery dropped to 9v everything lit up. I saw VSC and was like what the hell is VSC! The tow truck driver new instantly he said its your alternator. He jumped started my car and I had a meter in the trunk it was 9v with the engine running. Replaced the alternator everything is good now. You think the battery light or something would have come on before it got to 9v but nope. My car was a 2008 Lexus ES 350.

[@DocMackGarage]

The alternator was not completely gone, it was at reduced functionality on the way out, if not the car would not have started unless the tow truck driver charged the battery. When battery voltage goes low it throws just about every warning you can get, but the 3 lights I mentioned is relevant to this video.

[@officialilluminati9736]

I have a 2004 lexus es330. Whenever i wine down when driving. I do feel fuel smell. No leakage whatsoever

[@DocMackGarage]

It sounds like it is running rich, fuel isn't being completely burned O2 sensors , ignition coils etc. Mileage of the vehicle?

[@esnesio1610]

I have a 05 toyota rav4 and the code I get is p0560 . Low voltage. 😊

[@DocMackGarage]

I would probably say battery or alternator needs attention. Try charging the battery first.

[@TheDigitalThreat]

I have a 2012 corolla, and the Trac off/Check Engie have been going on and off (Toggles back and forth every few days). I have yet to see a VSC light go on. Could the gas cap still be the cause or would the VSC definitely be on as well if this was the cause?

[@DocMackGarage]

Is there anything that you did before this started ?

[@TheDigitalThreat]

@@DocMackGarage nothing

[@DocMackGarage]

@TheDigitalThreat I would start off with my first solution first, if it does not work go through the whole video and I have explained all the possibilities. Make sure to subscribe 😃

[@wendyholmes1411]

​@@DocMackGarage0

[@DocMackGarage]

@wendyholmes1411 I would recommend getting a car parts shop to run an OBD scan, should not cost more than $20 . Let me know what codes you get , I take you have tried my suggestions ? Also make sure to Subscribe to my KZbin Channel for free

[@jarfrobinksss]

This is for folks who have time to go "back to school", sit in class, learn and then try to apply what they learned with lots of time, tools, patience. Not for everyone. I'll pay the $ and move on with my life :)

[@DocMackGarage]

Mechanic ,costs a fortune, The DocMack Car Channel - Priceless 💵

[@thingshappen9199]

Sure. Some of us never stop learning. The mind is a terrible thing to forsake.

[@daniellang6112]

Used my obd2 and erased all codes. Worked.

[@DocMackGarage]

@daniellang6112 That is great but it will temporarily clear it if the issue still arises.

[@muzamilmuhammad5368]

I've just changed steering rak n i believe that is de problem of wheel allignment

[@DocMackGarage]

Yes correct I would say partially is. If you look through the video I have talked about steering and the components as well. Make sure to Subscribe to my KZbin channel for free if you haven't already.

[@alejandroalatorre8229]

I have a 2008 Lexus es 350 the issue here is check engine light & track control

[@DocMackGarage]

Hi, It will be the same issue

[@lagalagwelder]

Thanks for the info

[@DocMackGarage]

You are most welcome 👍

[@Nepausvlogger]

My lexus is 250 has tsc and check emgine light on

[@DocMackGarage]

Have you attempted what was described in the video?

[@Nepausvlogger]

@@DocMackGaragemay need to check o2 cencor

[@DocMackGarage]

@@Nepausvlogger Most likely could be

[@goranstamenkovic2928]

Got code p0138 o2 sensor bank1 sensor2!!! I change the sensor still getting same code!!!

[@StratBurst92]

My Rav 4 had this come on. Gas cap was OK, I disconected the negative terminal on my battery, waited 5 minutes and then reconnected the negative.on the battery. Problem solved.

[@DocMackGarage]

That will only temporarily fix it if you legit have an issue.

[@StratBurst92]

@@DocMackGarage New fuel pump installed.Still no check engine light.

[@DullesMignon]

Gonzalez Laura Martinez George Hernandez Carol

[@GODSTRUTHWINS]

Sometimes It is just a 40 amp fuse blew!

[@DocMackGarage]

Hello, it may be but this issue is mostly related to what I have suggested. When a fuse blows it can cause all sorts of other errors.

[@InezKennedy-i3g]

Thompson Jennifer Martinez Shirley Young Elizabeth

[@FlowerHarley-q5v]

White Mary Johnson Amy Rodriguez Thomas

[@supatotenkopf88]

Thanks Doc, is that a fine SAFA accent I hear?

[@DocMackGarage]

Thank you. I am from New Zealand. Please consider subscribing to my KZbin Channel for free if you haven't already

[@SayteaMorrilex-n8b]

Thompson Amy White Kenneth White Robert

[@TomOchoa-v1e]

Robinson Eric White Nancy Clark Laura

[@GuntherAmy-l1e]

Williams Matthew Wilson Sandra Harris Donna

[@KennanHerbert-v4u]

Hall Kimberly Hall Linda Jackson Laura

[@davidfowler2714]

complete waist of time

[@DocMackGarage]

How so ? I covered this indepth .

[@peacenlove8992]

Waste of time. Doesn't tell me how to fix it

[@DocMackGarage]

Is that so ? How did I not tell you how to fix it ? The video is long and covers alot of possible fixes .

[@neuterspadeyourpets.6201]

The third thing you have to look at is your ……. Sensor. WHAT ? I could not understand the word before sensor.

[@dougaustintx]

O2 sensor.... oxygen