I just started watching your videos . Don't stop you onto something big . Your content is really something unique you have a gift
@TheOffsetVolt3 жыл бұрын
Thank you Mukendi.
@johnb78052 жыл бұрын
Offset volt love your videos! Are you ok? Where are you? Selfish me would like to see more informative videos. It's been way to long!! Please come back soon!!
@francoisdastardly44052 жыл бұрын
+1 !
@aerofart3 жыл бұрын
Excellent video! Sufficient depth and illustration to give the material The coverage it deserves with engaging finesse in the presentation. I just discovered your channel and have subscribed. Can’t wait to see your other videos.
@TheOffsetVolt3 жыл бұрын
Glad you enjoyed it!
@mikhailbrest63852 жыл бұрын
@@TheOffsetVolt Thanks for your videos. Could you recommend books for circuits analysis for bjts, fets which your videos about stability are based on?
@raygosper16562 жыл бұрын
Must say you are certainly putting together very good content and subject matter and in a format that is easy to follow and understand for the most part. Hope you keep up the good work as you are enabling easier understanding for those entering into electronics and those who require further clarification. Most in the area of teaching seem to get to bogged down in the mathematics and cannot break it down and relate to practical application which is needed for students to gain a comprehensive understanding. Something to consider, it would be good if you attached your worksheets to the topics covered, would help also.
@ohmslaw68562 жыл бұрын
Hope all is well with you.. you haven't posted in awhile.. God bless
@andymouse3 жыл бұрын
Very nice tutorial....cheers.
@TheOffsetVolt3 жыл бұрын
Glad you liked it
@davidluther39552 жыл бұрын
EXCELLENT PRESENTATION.IF YOU PLACED THE ANALOG METER FLAT ON ITS BACK WOULD THIS GIVE BETTER RESULTS?
@Iosens11 ай бұрын
Very nice video! Concerning calculation errors in percent though, I would suggest this formula: ((Wrong value - Correct value)/Correct value)* 100. Wrong value = measured value, Correct value = expected value. At 17:54: (19.56 - 20) /20 = -0.022. Times 100 = 2.2% . 19.56/20 is NOT the error. (The tables were calculated correctly.)
@Jnglfvr Жыл бұрын
At 2:50 it would have been nice to compare the burden voltage using the bench DMM. Based upon it's specs and using 1 amp current range for this 200 mA circuit it appears based upon the data sheet at 10:55 that it using a 0.7 V / 1 Amp = 0.7 ohm shunt resistor. That would have given a measured current of 2/(10 + 0.7) = 187 mA. About a 20 mA improvement over the handheld.
@kaybhee63 жыл бұрын
keen
@skippy8223 Жыл бұрын
WHEN IS THE NEXT VIDEO??????!
@johnb78052 жыл бұрын
Does anyone know what happened to The Offset Volt?
@TheOffsetVolt2 жыл бұрын
Hi John, I'm still alive and kicking. I have had a lot of knew stuff out of my wheel house to learn for work so the channel has been sorely neglected. I hope to start something again soon. Thank you for watching.
@johnb78052 жыл бұрын
Glad to hear you are ok! Will be looking forward to your return! I am going to be selfish for a minute and ask if you can do a video or a series of videos one day on FM stereo multiplexing. In other words, FM Mono, and then how the fm stereo signal is generated at the transmitter and how an analog FM radio decodes the signal into the left and right channels and what is meant by channel separation. I have watched some other people on youtube go though a standard FM receiver alignment and I seem to have more questions and confusion when they are done! That is if you can spare the time to go through a typical analog receiver looking at how it creates the 38khz sub carrier and its importance in finally generating the final left and right channels. Again, glad to hear you are OK and will be back hopefully soon! Thanks for Reviewing! John
@mrprad74252 жыл бұрын
@@TheOffsetVolt come soon
@keithmaddox14693 жыл бұрын
amplify the signals and subtract the difference. Better yet, use a kelvin connection.