Thermal-Structural coupled Analysis of Disc Brake and Fatigue Life & FOS calculations in ANSYS

[@sanketghadage3201]

Thank you so much for the valuable video🙏❤

[@TechnoMechEducation]

My pleasure 😇

[@SumonsMultimedia]

nice videi

[@FaithAtanda]

Good video. However i would have loved that you add video of what is happening on the brake disc also.

[@TechnoMechEducation]

Sure

[@entertainment6965]

Very nice

[@tuts4u608]

Great work

[@duongminh6239]

Hi sir, Can you explain why you choose the temperature is 80°C? Thank you so much.

[@TechnoMechEducation]

This is just a tutorial video for learning purposes.. the initial & boundary conditions may be different.

[@mohammedelaminekhial6474]

Nice work bro ❤️

[@TechnoMechEducation]

Thankyou

[@soufianeelogri5020]

I'm not sure if the fixed support is suitable for the thermal expansion of the selected face. I will opt for the remote displacement (Fixed all Dofs) with Deformable behavior

[@aneesurrehman4135]

if i attach the brake pad and find friction what ansys module should i use

[@sudhanshusanagavarapu2808]

Sir, why have you applied the pressure only on one side in the static structural case?

[@TechnoMechEducation]

That’s a mistake.. you should apply both side of the plate.

[@raghavsharma3901]

Can u suggest the material for brake disc rather than SS n Al

[@TechnoMechEducation]

Try composite materials 👍

[@harshmadnani1613]

What procedure to follow in case i need the thermal and structural analysis by the friction between two disc rotating in opp direction and rubbing against each other

[@TechnoMechEducation]

You need to perform coupled thermal & structural analysis

[@harshmadnani1613]

@@TechnoMechEducation what about thermal fluctuation due to Air on a radiator?

[@shaun2983]

Sir, Why did you only apply the temperature to one side of the rotor? I believe the temperature at either side should be the same?

[@TechnoMechEducation]

Yea… should apply on the both sides. That was a mistakes… seen after uploading it

[@shaun2983]

@@TechnoMechEducation Okay thanks for your response!

[@NRINFORMATION]

ماشاء اللہ

[@wasekar]

is it possible to have a squeal analysis pl share the video

[@TechnoMechEducation]

I didn’t understand what u mean by sequel analysis?

[@haidarali-qu3fx]

Can you zoom the option which is used by you to draw and explain the diagram.

[@TechnoMechEducation]

haidar ali which option ur asking about ? Actually the model diagram has created in Modeling software PRO E. and imported here in ANSYS

[@TechnoMechEducation]

haidar ali I think hight resolution quality will give to clear look of options & methods.

[@pavanyashoda4937]

Super sir

[@kamalahmed6055]

Can you do analysis on electromagnets system

[@TechnoMechEducation]

My schedule is very hectic but I’ll try to upload in weekends.

[@wasekar]

how can we do simulations by configuring with different materials

[@TechnoMechEducation]

Yes we can add number of materials. Go to Engineering data and add multiple materials according to ur requirement as the video shows in starting. Then after importing geometry Select ‘ASSIGNMENT ‘ and select ur material accordingly

[@sumanmahanand2059]

Very nice #myrecipebook

[@bhushanwandre8703]

Very nice video sir! But, i am confused which analysis to choose for a component like the same problem solved by other guides in static analysis. Will you please tell how to choose analysis type?

[@TechnoMechEducation]

Thank You.

[@TechnoMechEducation]

First you should clear Which analysis is required only structural or Thermal, or both you need to do

[@TechnoMechEducation]

If you want to find stress & deformations etc due to Forces then Static structural Analysis is required to choose. And if you want to find thermal flux, temperature distributions then you should select Thermal Analysis.

[@TechnoMechEducation]

Hope you understood

[@bhushanwandre8703]

Thank you for your reply!

[@seyoumyonas2634]

can you kindly attached the file that you use as input please

[@TechnoMechEducation]

Sure… send ur email

[@TechnoMechEducation]

Sure… send ur email

[@haidarali-qu3fx]

Why bcz options are used, not visible

[@abdouachouri143]

can u plz send the file

[@TechnoMechEducation]

Pls share ur mail I’d or contact me on Telegram

[@abdouachouri143]

@@TechnoMechEducation thank you i made it already thank u anyway

[@burakeskin4454]

hey you can send me project files?

[@abhilashreddy6474]

Sir, can get ur contact. I have to speak with you regarding this analysis

[@TechnoMechEducation]

Contact on telegram t.me/TMEofficial