Thermo King alarm 37

[@jiyesh100]

Was very helpful but pls can you make videos in details practical will be more helpful Thanks...

[@dex4210]

I need some help getting this cooler to run

[@joshuam1146]

whats going on with it?

[@djaffartablat5562]

pourquoi mon thermoking affiche la tension batterie grimpante de 12a25v puis le compresseur s'arrête et affiche code 25 alors que sur l'alternateur il y'a 14,2v avec mesure de multimètre ?

[@naushadali95]

Please make video on tk 500 on alarm code 17

[@pablitoburciaga7351]

Tk md200 alarm 35 Already check my pressures, bypass hp switch, unplug my fuel solenoid & fuel pump Still alarm 35, replace the relay board and also I have a spare micro What else to check ?

[@joshuam1146]

Pablito Burciaga does the engine crack? Or does the alarm come up right away and the control starts blinking?

[@pablitoburciaga7351]

@@joshuam1146 No it doesn't crack the buzzer stay on then it blinks alarm 35 Notice not getting power supply to fuel pump when the buzzer it on . I used my power probe and get the fuel pump running

[@joshuam1146]

Pablito Burciaga hi! Check all your fuses. There’s a plug on the engine side that goes down to the fuel pump. Disconnect it and retest, just to rule out that section of wiring from the fuel pump to that plug. Otherwise its looking like there’s a electrical short somewhere in the wiring. You’re gonna ha e to follow all the wiring, I can email you a wiring diagram in case you need one

[@pablitoburciaga7351]

Thank man for your help found out the unit had to 2 problem one was the fuel solenoid and the other one was the starter

[@amineminos5253]

Mode cycle sentry not displayed on sceen

[@joshuam1146]

Amine Minos if it's not displayed cycle through the control until you hit cycls-yes or no. If you want the unit to cycle on and off change to yes and press enter. If you want continuous change to no and press enter

[@pedromoreno3214]

tengo un problema no puedo bajar ni subir temperatura en un equipo themoking.solo baja a 34f y sube hasta 36f...que hago para que baje mas y suba

[@joshuam1146]

Pedro Moreno se tiene que meter a super guarded menu. STH es la temperatura máxima que se puede set. Y STL es la temperatura baja que se puede set. Cambie esas temperaturas a las que quiera el cliente...

[@23cetona]

My reefer shuts off before it reaches to set points and display blinks. Code 33 check engine rpm What can I do I

[@joshuam1146]

Reaper48 _YT check your engine speeds, either the engine is running too slow in low speed and high speed OR its running too fast in high speed. Most recommended speeds on tk md/kd/ are low-1625. High-2425 both +-25 but that depends on your unit. another problem may be on your rpm sensor, check the wiring connections on the sensor. Send me the model of unit you have...

[@23cetona]

Thank u How can I fix it?

[@joshuam1146]

Reaper48 _YT all depends what the problem is

[@jimmygujjar8350]

Alarm O2 fault active in my refer .kindly send me video to in activate ..Thermo king sbiii max

[@joshuam1146]

jimmy gujjar if you can’t erase that alarm most likely you’ll have to replace your evaporator coil sensor. Beware because it may be a graded sensor and you have to go in super guarded access to change the grade.

[@antonionajerabadillo7412]

Buenas noches tengo un problemita con el Thermo se me activa muy seguido el defroster ya le cambié el sensor que va oculto con sintaxis es el no graduado y sigue la falla

[@joshuam1146]

Antonio najera badillo revisé el defrost air switch

[@10btiger]

Hey what is code 148 on Thermo king

[@joshuam1146]

Yasha Bezginov hi! Alarm 148 is auto switch electric to diesel disabled...

[@jeromecampbell3699]

hey bro i have a problem with a code number 74 can u help me out

[@joshuam1146]

Jerome Campbell hey sorry I took forever to get to you. Alarm 74. You have to get into guarded access menu, bring down the service hour meter back down to 0. While you are in guarded access, alarm 74 should display, when it does erase it. It will not appear until the unit reaches the hour limit again.

[@joseeugenio972]

alarm 61 como limpar da tela

[@joshuam1146]

José eugenio da silva cuando la alarma 61 este en la pantalla, empuja el botón = y se va a borrar. Esa alarma es de batería baja, asegúrese de que estén cargadas las baterías...

[@j.p.8961]

saludos puedes subir un vídeo en español indicando como resetear las alarmas y cual es la función de cada uno de los botones d este thermo king? gracias de antemano trabajo con un camión que utiliza un thermo king de estos y cada cierto tiempo no prende y lo debo llevar al técnico el le toca los controles y hace que funcione de nuevo sin hacer mas nada y pierdo tiempo en ir al técnico.

[@jodycampbell2515]

Code 35