Forgot to mention the case is fully reversible, so you can flip the motherboard tray around and have the mobo on the right side, PSU on the left, etc. Kinda cool, but hardly unique. IMO you'll still need to run a custom loop & leverage more of this case's features for it to be worth the $179.99 US MSRP. Feel free to share your thoughts.
@ChrisBrett23 жыл бұрын
I mean you're paying for a high-end case. It feels like the design was rushed with oversight, it is still a good-looking case nonetheless.
@dolphin58083 жыл бұрын
The black one is $149 and the white one is $159
@writingpanda3 жыл бұрын
Is the riser cable PCI-E gen 3 or 4?
@zaphod42453 жыл бұрын
It also seems as tho you couldn't use the upright mount for a watercooled gpu, as the inlet/outlet ports that protrude from the card wouldn't fit with the front panel on. I guess the EK 30 series FE blocks would be ok, but other than that, the block wouldn't fit
@2000impalalsx3 жыл бұрын
So you can mount your GPU with the upright kit and the rad on "top" in the reverse setup. Then remove the plate for the back and 120mm on the side or the mesh front panel
@CTTechGaming3 жыл бұрын
This may have been mentioned but in case you didn't know. the removeable plate on the case behind the GPU can be reversed which will give you much more room when mounting the GPU in the upright position
@calemf152 жыл бұрын
was just about to say that
@ModernMetaphysicae Жыл бұрын
This ^^^^^^^^
@mrbabyhugh6 ай бұрын
this clown that Lian Li sent their very well thought out and also well documented hardware surely DID NOT READ the manual before he went on to turn on a camera and made this crap to post on the internet!!!!!!!!
@PitboyHarmony13 жыл бұрын
The rear plate for the upright GPU, not the bracket but the plate itself ... is reversible. If you inverted that plate it would set over an inch further back in the chassis. That means that the bracket would also be set back, which means you wouldnt have had a problem with the rad up top, or fans, or be too close to a rad or fans on the bottom, and/or you could put a 240 rad on the front panel. The reversibility of that panel is key to the design ... I guess you missed that.
@OhItsThat3 жыл бұрын
Personally I like my GPUs mounted traditionally. I like the look of the backplate, side of the gpu and Pcie cables over the look of the fans.
@cashlgan48353 жыл бұрын
I like vertical for liquid cooling
@Revolution053 жыл бұрын
imagine my build but in an Evo.. that's what it will look like with watercooling and cable management
@mikerzisu95082 жыл бұрын
Same
@schwanzmunster25032 жыл бұрын
I also prefer that. Plus after all the bad things I've heard about riser cables, I don't trust them
@benny_19852 жыл бұрын
100% in agreement, I love the look of the exposed cooling fins along the side, like it is unbuttoning its shirt 😂
@Admiral_Nimtz3 жыл бұрын
The problem is you didn't turn around the mounting plate that the GPU holder can bolt to. The front right side mounting plate not only can be changed but is reversable an moves it closer to the right outside panel giving you more room on the inside of the case to mount the top rad an fans. Looks like you rushed this build a little to get the review out.
@kaioken14823 жыл бұрын
Agreed. Should make 2 separate vids as for in depth review of the case and all the add ons, and pc build in it. It did seems rushed and not properly planned build. Hope maybe they will have another build vid on it.
@ErgonomicChair3 жыл бұрын
Yeah and his assessment is just bafflingly dumb. "The average builder can't use this! It'd be a waste!" Why? It's not much more and if you have a GPU mounted normally, it'll be just as good as the tens of thousands of builds using other Lian Li 011's? Not onlt that but these cases as we know can even work with vertical GPU's too etc etc. There's no NEED to custom loop this at all, and he simply built this terrible. Liek this is a garbage build, if you showed me pictures of this and went "The verge built another terrible computer!" I'd believe it was the verge lol.
@dukng95022 жыл бұрын
Or a 120 mm rad could've been used instead of the featured 140mm NZXT
@jaymacpherson81673 жыл бұрын
If custom painting of a case is “basic,” then this case is a dream with all its and modularity. Strictly from a parts build, I still find it a leap beyond most alternatives as one vendor has it listed for ~$150 US. That price seems very competitive given its flexibility.
@blai5e7303 жыл бұрын
The O11D XL has the same GPU anti-sag bracket. I vertically mounted my GPU so I didn't need it but I did install it in my other rig (Phanteks 719) that has w/cooled SLI'ed cards mounted traditionally and it works very well - no sag, no wiggle.
@EpicMind5003 жыл бұрын
What GPUs do you have SLId?
@blai5e7303 жыл бұрын
@@EpicMind500 - 1080 TI's with EK water blocks.
@b0neheads Жыл бұрын
what gpu vertical mount did you use for the O11D XL
@blai5e730 Жыл бұрын
@@b0neheads - EK GPU Holder EVO
@b0neheads Жыл бұрын
@@blai5e730 thanks so much 😁
@steveburns12422 жыл бұрын
I've just received this case and it's an absolute gem. I've done a couple of builds in the past so no expert but this case can be utilised for a basic or advanced builders. It lets you customize in so many ways, including reverse, which if like me you need to switch the viewing side of your rig is a big deal - how was this an after thought?! Yes, inverting a case is not unique but to be done this well actually is. The negativity in this review is dumbfounding for a case this good - cable management, modularity, aesthetics all bang on the money. I was totally opened minded about choosing a case for my new build but after reading countless reviews I knew this was the one, I wasn't disappointed! This case was made for the community from listening and implementing their ideas. Great job Lian Li & Der8auer. Do yourself a favour & read/watch some other reviews before being put off by this one.
@TheSjuris2 жыл бұрын
All Bitwit had to do was remove the drive cage.
@noahporkchop2 жыл бұрын
if you bought the gpu mount, can you send the link?
@mannyfresh70652 жыл бұрын
yeah this felt really rushed and not planned
@TheSjuris2 жыл бұрын
@@mannyfresh7065 the 011 dynamic series is pretty much the best selling diy case in the market. This one is an improvement over the original one.
@mannyfresh70652 жыл бұрын
@@TheSjuris oh trust me I agree. This case is really amazing and debating on going from my O11 mini to this. However Kyle didn’t do a great job showing off all the features and really downplayed the innovation on this case
@eveypea3 жыл бұрын
One more addition which would be small but awesome: A rear PCI slot panels that has the relocatable "front" I/O connections. If you can decide which side to locate those ports, why not put them on the rear? Also: To put the radiator at the top, why not rotate the GPU 180 degrees with the outputs on the bottom?
@twitchmania76142 жыл бұрын
Dude the whole point of “front” io is so you have easily accessible ports. Why tf you you put them in the rear?
@roytasanen59782 жыл бұрын
I got the case for almost a year now , lian li did a great job with this case . Theres plenty of room , you can customize it in so many ways and it looks amazing
@xii-nyth41013 жыл бұрын
in a normal case with fans in the front, having a video card facing forwars (1 90* turn from original position) would be really optimal, this is why I like cases with fans on the bottom such as this one, pretty sure they snuck into my room and took my design though since I also put fans on the side....
@PhilPhysix3 жыл бұрын
well to be honest this review seems rushed and not thought through. a lot of wrong explanations and the critics you took on the case all seemed like you did not have a clear thought on how to do things. GPU power for example: you could easily run the cables below/behind the gpu through the gromit directly to the psu. do you really complain about the temps when not even fitting the case with fans? why not put a 360 rad at the top and 3 fans at the bottom? it's like you actually try to make the case look bad. i hope you remake this review with a bit more thought behind it. yeah just feels like a not well made video. actually even a badly made video.
@ghostisbusy21702 жыл бұрын
Ok here’s the problem with this comment, your trying to prove a point to a KZbin creator with millions of subscribers who is probably never going to see this comment. Also have some respect for people that provide content FOR FREE to people like you. Making a complaint here does nothing except waste your own time. I’m not insulting or gaslighting you, I’m just giving you some advice.
@KnaGGelMan3 жыл бұрын
The should've made the hdd cage in a way that you could mount a 5,25" ssd cage.
@RyanFennec3 жыл бұрын
@Ladioz y
@tfsmcpe94023 жыл бұрын
@Ladioz hdds are cheap and high capacity ssds are really really expensive
@toxicturkeyy3 жыл бұрын
@Ladioz you don't have to use them you know. It's just an option for those who would like to. Also, ssds are really expensive compared to harddrives. Just a 2tb sdd one compared to a harddrive can easily cost 3x-4x times more.
@4x4forlyfe3 жыл бұрын
I can't really figure out why you were so set on mounting a 280mm AIO or 140mm fans at the top or bottom. Why not install a 360mm AIO at the top and some triple 120mm fans at the bottom? Then you wouldn't have clearance issues with the side mounted GPU. Furthermore, I'm pretty sure there is a way to mount the other side panel behind the GPU to mount fans. You just have to get creative. P.S. - PCIe 4.0 extension cables do exist on the market and would allow you to run that cable behind the motherboard for a much cleaner look
@rusty50043 жыл бұрын
Probably sponsored build by ASUS considering its all the new'ish white ROG components. Definitely hits the quality of the content in this case.
@jaymacpherson81673 жыл бұрын
Good point. Three 120s can move more air than two 140s at a specific sound level.
@normustafa872 жыл бұрын
Exactly
@deViant142 жыл бұрын
@@jaymacpherson8167 source? Personally I hate higher pitched fans so I think it would be hard for any configuration of small fans to be better on sound. That said, I have 5 140mm fans so I might be biased.
@jaymacpherson81672 жыл бұрын
@@deViant14 Look at the flow specs for most manufacturers’ fans. For example: NF-A14 PWM 140.2 m3/hr x2 = 280.4 m3/hr vs NF-A12x25 PWM 102.1 m3/hr x3 = 306.3 m3/hr. Last I checked 280.4 is less than 306.3. And you can check the sound levels yourself, which are lower for the 120s.
@rowanpeacock88923 жыл бұрын
its like one of those customisable cases with panels and setup
@Kozi033 жыл бұрын
That sag bracket is literally the best. I bought one on its own 6 months ago to use in my NZXT 500 and worked perfectly!
@kasper_4293 жыл бұрын
3 things. #1: I'm pretty sure you're meant to use the fan bracket with the upright GPU mount so you'd have big, wide-open spaces (yeah!) to route the PCIe cables through. I could be wrong, idk. #2: IMO, the upright GPU bracket is just a gimmick and was clearly not thought through that well. It would look a lot cleaner if the riser cable was just a bit longer, so you could run it through the cable grommet right beside the GPU and then up through the bottom hole (if it were wide enough) where front panel connectors and fan/RGB cables would normally go. #3: I feel like 99% of people would just use the regular GPU/PCIe slots or the normally-vertical GPU mount that attaches where the PCIe slots are. The "upright" mount is just for show, IMO. Besides the things mentioned above, I love this case. They really improved on the design and the modularity is amazing.
@playeronthebeat2 жыл бұрын
length of the riser cable is absolutely my biggest down side for this case as well. The rest is managable. This, however, is pure garbage. You could fit it easily through the grommets and below the motherboard. It just needs to have the appropriate length. Sadly, though, they didn't do that for the final version. :/ But still, I guess I'm gonna buy that case and that accessory... The case is just too much perfect for me and my use case. Maybe I'll find another riser cable or something that'd make this thing work like a charm!
@normustafa872 жыл бұрын
I recommend a 600 mm PCIe gen 4 riser cable.
@MrInksane912 жыл бұрын
You can use the fan bracket on the side to mount the upright GPU as well. So you'd have 3 exhaust or intake fans behind the GPU moving air. Lian Li advertises them to be exhaust fans.
@DalisYn3 жыл бұрын
I’ve seen other builds with 360 rads with the gpu mounted like that. You’re the first to have this issue
@humm_vee_wusky62733 жыл бұрын
Nexus talked about the price of the case and it cost too much for the case it self not counting all the extras you have to pay for shat really should come with it. They're just being greedy with the cost of a basic-looking case.
@mauricioyoung66683 жыл бұрын
Like not even a couple fans? C’mon
@RyanFennec3 жыл бұрын
@@mauricioyoung6668 tbh most fans that come with cases usually suck, I prefer buying my own fans to put in them (that's just me tho xd)
@darkzak473 жыл бұрын
I’m doing a build for my wife and I almost bought this case, but then I thought that it might honestly be a bit too much, and I’m glad you agree for a basic build. Furthermore I found a TUF gaming GTX 3080 TI video card at Micro Center. Yours for the low low price of $1900 🤯
@elpatomaton63333 жыл бұрын
rtx
@CoalitionGaming3 жыл бұрын
@@elpatomaton6333 thx for the correction I had no idea what GPU he was talking about at all until I read that
@Almin883 жыл бұрын
@@elpatomaton6333 thx for the correction I had no idea what GPU he was talking about at all until I read that
@williamreed65043 жыл бұрын
@@elpatomaton6333 thx for the correction I had no idea what GPU he was talking about at all until I read that
@jonasVD3 жыл бұрын
@@elpatomaton6333 thx for the correction I had no idea what GPU he was talking about at all until I read that
@mobilechaosyt3 жыл бұрын
The riser cable is still going to be an issue even if you go water cooled. You could hide it with the loop a little better.
@swizzler80533 жыл бұрын
You can ziptie them.
@mobilechaosyt3 жыл бұрын
@@swizzler8053 Where? the riser cable still has to go from the PCIe slot to the graphics card. The route for this consistently the same.
@Blasty133 жыл бұрын
would it have been easier to feed wires through for the GPU if you used the fan holder panel instead of the HDD Panel?
@Hoof303 жыл бұрын
Came here to say this. This would have been much easier for him.
@mz19063 жыл бұрын
rad on the bottom pushing heat into the case (not to mention pump priming issues for AIO pump) and a dumbass side GPU mount no one does, verge build V2, kyle edition
@neilbradley3 жыл бұрын
"The last time a girl saw your junk, she thought Bob Ross had been resurrected." LOL!
@timf25333 жыл бұрын
If you did a custom loop in this case, could you fit a 240 rad with fans up top with the GPU in the upright configuration? Another thought would be with the GPU taking up the normal Pump/Res area you would almost need to go with a distro plate on the front, so you don't end up blocking the view of the GPU which again is kind of a main reason for going with this case.
@JasonTaylor-po5xc Жыл бұрын
I did a build with this case. I got a good deal at Micro Center in my area, so I got it over the XL (which was full price). Not a bad little build. I mounted the AIO Radiator (GA 2 Trinity 360) on top. Single fan set (not push/pull) blowing out. I mounted the GPU (2.5 slot) in the traditional location - no riser cables or other nonsense. 1 120 fan in the back blowing out (traditional). Bottom set of 3 fans intake. Side set of 3 fans intake. This is a 14700K with the RTX 4070 Ti build with the Avermedia PCIe capture card. All works really well. Looks pretty good to since I went with the Lian Li Uni v2 fans. System will be mainly recording, streaming, and light video editing. Specs are a bit overkill but got a nicer system because of BF specials and the PCIe capture card requires NVIDIA GPUs for 60fps capture - otherwise, I would have opted for the Intel Arc A770 and a lower end chip. I do agree, this case goes on a desk not the floor - which I true for any "showcase" PC case like the O11D series.
@kevin1337ninja2 жыл бұрын
Just a quick question, isn't that AIO going to die quicker the way it's installed? Seems like air is going to be trapped in the pump.
@LoliNoxTan3 жыл бұрын
The only way I see the riser cable working is if it was longer and you could route it behind the case. Problem is that if you could route it behind the case, you would be potentially blocking off PCIE slots. (if you go down) I honestly don't see a situation that the riser cable wouldn't look bad. Lian Li didn't stop to think if they should
@thepunncake3533 жыл бұрын
for the first time i actually watched a manscaped advertisement. that one was good
@rktsigntist2 жыл бұрын
1. If you build in reverse mode, no radiator issue, 2. side fans go behind the gpu, 3. There is a 600mm riser cable.
@bleu502 жыл бұрын
Please do the redemption build in this case with the upright gpu and custom loop. ALL WHITE!!!
@ansonikuaigura2 жыл бұрын
I wonder if getting a long riser and going through the bottom holes to the back side instead would look better? It would be better if the fan back plate worked with the vertical mount.
@guerrillaentrepreneur59993 жыл бұрын
This case is TOO EXTRA.......? This case is: Overkill for a basic build A bit too much for a basic build Is a better match for an advanced build than your basic build Etc...... TOO EXTRA that is too funny.
@ams710072 жыл бұрын
you should do a intel 13th gen build with a carbon and silver theme in this case. you could use the lian li mirror fans and a msi z690 carbon ek x with a evga rtx 3090. you could also add a distro plate in the front. you would have to mount the pump/resivoir in the bottom on a rad. this would be a great build to do custom water cooling in and it would be a epic build!
@That_Dude883 жыл бұрын
I was excited when I saw this review about the evo. But, you should have done your research on this case. That back plate you installed is causing your heat issue. You should have left the other fan bracket on. Please do a second review later.
@MarkVP3 жыл бұрын
Pre-ordered mine today. Super excited to build in this beast. Anyone interested in buying it, I would preorder soon. Most likely going to sell out fast like the last one.
@TruthYouNeed3 жыл бұрын
HENRY CAVILL BROGHT ME HERE
@thankskanye15213 жыл бұрын
Same lmao
@Marcandre113 жыл бұрын
Wow AIO under the CPU … please check Jay’s video on this topic. You should also check Jay’s video on this case he went further on explaining all the features.
@link37403 жыл бұрын
inverted motherboard, add a 120 mm distro plate (phantek makes one) to the rear fan slot, dual 360 rads, and try to do runs using any bend adaptors.
@RainMan523 жыл бұрын
Kyle, is everything Ok my dude??? Take that break if you need it.
@FarmerKlein3 жыл бұрын
So GN showed the case can rotate or flip on its base. Wonder if when flipped how the rad would end up vs being on the bottom now.
@jonraquet66293 жыл бұрын
Just transplanted my pc into the 011D and I love it! Super modular and looks amazing!
@TacticalBeard3 жыл бұрын
Some nice upgrades over the previous versions. Looks like it has better vetnalation vs the slits in the metal on the top and side from older versions. I like my o11d XL so much I’m going to do my first n water loop in it because EK makes a massive distro plate that looks to cool. That vertical GPU mounting setup is yikes tho takes away almost all of your radiator, fan support
@Matt-gf4gd2 жыл бұрын
I get where you're coming from, but I think it can be done to make it even more cooling efficient in vertical upright position given you get a much more efficient air stream in the unobstructed "chimney" cooling format where fresh air sucks in the bottom and straight up through the exhaust. Also you can get a slim 20mm radiator and slim fans and fit a 3rd radiator behind the vertical GPU. Just food for thought.
@MoparMooser2 жыл бұрын
@@Matt-gf4gd there is some other dude on here that did a break down of thermals for different fan configurations, and no matter how you do it, mounting the GPU upright causes higher temps for the GPU and the entire case. The main reasoning is that those side mounts provide great airflow for a radiator and the gpu is blocking all of that space and pushing hot air off of the GPU into the center of the case. Obviously its normal for a gpu to do this, but this issue lies with the gpu covering a massive vent allowing air to only come in from the bottom and out the top. If the side is used as an intake radiator, then you’ll be pulling in air from the side and the bottom allowing for a bigger surface area for the air to flow. All that being said: if you like the upright design and your temps don’t get out of control, by all means go for it. I just don’t see very many people buying a case like this to NOT attempt to take advantage of the airflow
@Matt-gf4gd2 жыл бұрын
@@MoparMooser I actually didn't notice much worse temps in the upright. You can still probably mount a radiator there as well.... There's plenty of space leftover, depending on your card... I'd say about 40-60mm behind the GPU. I tried different orientations and found that the upright position lowered my CPU temps and increased my GPU temps slightly, but not by much. I found an odd orientation seemed to work pretty well where I mounted a 140mm fan as intake behind the GPU in upright at the bottom and an exhaust 140mm at the top behind the GPU. Thermals seemed pretty good with that setup, though I could see using the whole side as intake unobstructed probably gives slightly better thermals. I'm intending to go custom loop water cooled though with a bottom and top 360 radiator, so it wouldn't be an issue. If you're doing all air cooled, then probably a few % less optimal, but for the trade off of aesthetics I still kinda like it personally.
@rainchewyman1003 жыл бұрын
Thanks for the vid Kyle! Little constructive criticism though, the background music in this vid was distracting and cut out at strange times. Not sure if that was intended but yeah.
@HeartBreakDrip3 жыл бұрын
The idea of having that huge riser cable spanning across the mobo for the sake of that vertically mounted GPU is insane. This would be purely a performance move for people who do not care about aesthetics. I appreciate the innovation and modularity but this just simply seems like a classic case of "if it ain't broke, don't fix it.".
@normustafa872 жыл бұрын
I get what you’re saying, but it’s possible to buy PCIe 4 gen 600 mm cables that can go behind and around the motherboard. That way it won’t be visible. I get what you are saying tho, you gotta sacrifice a little money for the looks.
@azarik47102 жыл бұрын
Bitwit, you are only one YT who show properly Lian Li 011D Evo with GPU in upright position plus shows where cable coming from and how are there are connected to GPU.Not like most of rest, who's gpu are either not connected or cables are hided!! Ive spend a long time looking for it, so i'm sincerely will say -Thank you!
@JoJoBaB.y3 жыл бұрын
The LED riser cable for the gpu would look sick imo
@rubilacxe0332 жыл бұрын
Yeah i just switched to the O11 D Razer Edition. Matches my mouse and keyboard. love it.
@auschris92963 жыл бұрын
the best case wit a sag bracket that is removable ive seen to date was actually the rosewill prism s case i used to have, for some reason when i sold the case i kept it, and the bracket works perfectly in my nzxt h710i case for my 3070ti ftw3, i put it on the bracket that hides the cables and i belive supports a watercooling resivor, that little slit on it is perfect to mount the fold out sag bracket!
@levigoldson42422 жыл бұрын
I think this is the most critical review I've seen so far of this case. Not a complaint, I like the downsides being pointed out when making a purchase decision.
@jasonc33303 жыл бұрын
Slamming on a new innovative case without reading a manual.
@Admiral_Nimtz3 жыл бұрын
I also forgot to mention not only is there a mesh front option but the solid inside panel has a open mesh option that is also reversable on the front right to again make room for the GPU. In my opinion you didn't give a accurate review of this case, instead a rushed half done build that is far below what this case is capable of.
@DJaquithFL3 жыл бұрын
Umm route the PCIe 3x8 pin behind the GPU and not through that teeny tiny hole. There are other PCIe 4.0 riser cable extenders that are longer so they can also be routed behind the GPU and out of sight. For reference see GGF Events YT review.
@studog8585853 жыл бұрын
Appreciate the shoutout. Amazes me people of this calibre don't do research.
@get2choppa3 жыл бұрын
kyle: thumbnail of the aio on the bottom with pump on top steve: heavy breathing
@itzamedave62422 жыл бұрын
Air in AIO will go to the highest point of the system which is the actual CPU block so wouldn't mount the rad at bottom.
@playeronthebeat2 жыл бұрын
The only thing that's killing me, personally for the accessory is the fact that it seems like you aren't able to route the riser cable behind the motherboard. Why didn't they include a riser cable that's long enough to fit this? This cable just... Destroys most of the atmosphere this case gives. Now you gotta probably buy a different riser cable if you want to an upright built in that case so that this cable won't be just running all over your built :/
@jonmarshall34142 жыл бұрын
Only need to remove one panel to access gpu cables. The sides can come off now without taking off the top
@mowingkid10ultimate513 жыл бұрын
if you could id love to see a medium level computer with like a 5800x or 5600x with more like a 3080 or 3070 and a cool theme id say would be a nice simple red and black or a semi industrial ish theme thank you for your time for reading this whoever :)
@lowellford34192 жыл бұрын
I would never put an AIO radiator below the pump housing. Over time air can build up around the pump and near run dry. Mount the radiator for an AIO "above" the cpu level like at the top of your case...not the bottom.
@TTVveenas3 жыл бұрын
If you look on his desk @ 0:13 under that light, you may see a beer bottle :). Drunk?
@orrygel3 жыл бұрын
The gpu kit comes in pcie 3 and 4
@OriginalMergatroid2 жыл бұрын
Beautiful case, but I feel the mesh should come standard on it, not the glass. I would also like to have the top I/O as standard instead of the little module. I have no issues standing up to plug something into a usb port. The vertical GPU mount seems gimmicky. Too bad you can't custom order cases like this and select the parts you want to come with it. I like this case more than my Meshify 2 XL, but not at the additional cost of customizing it the way I would like it to be. I would like it with the mesh front, the solid front panel in place of the vertical video card, and the top metal panel with the I/O holes in it. I should be able to call them up, tell them what I want and they ship it to me without the stuff I don't want.
@gobble38603 жыл бұрын
This is the best sponsor mention I've ever heard.
@EliteLaser-fo3td3 жыл бұрын
i love how dirty his mousemat is, it shows how much he uses it and spills stuff on it.
@franzs13 жыл бұрын
18:37 you could show how easy the case can be inverted, and build a unique pc in this way
@justatim81432 жыл бұрын
I like the Evo BUT Not without the front mesh panel and some fans for the $189.99 starting price. You now have to buy the front mesh panel if you can find it for $19.99 plus since no fans a min. of 4 fans plus extra fans for better cooling. If I was building in this case I would have 3 front, 3 side, 2 bottom, 1 rear and 3 on the 360 radiator on top. That's 12 SL infinity fans at $400,case at $189.99, front mesh kit at #19.99and a vert GPU at $69.99 which is now over $700 total for a nice build in this case with all the add-ons. The Lian Li case just like many others they sell are WAY TO HIGH PRICED for what you get.
@Z1M0Z1M2 жыл бұрын
So theres an issue with the Strix OC Cooler while mounted in the upright position. If the case is inverted, the Strix Oc card can drop close to 20c. It has something to do with the design of the Stric cooler. Not the case. Great case for a custom water cooling build.
@anthonyholmes59653 жыл бұрын
Do a Superman theme and see if he’d be interested in collaborating with you in it. Or a Witcher theme. That’d make a sick custom build.
@riccardopozzati30072 жыл бұрын
Maybe I should go for the regular O11 Dynamic. Now I have the O11D Mini but i need more space to install two 360mm radiators. I don’t care about the new features of the O11D Evo (like the upright GPU kit or the possibility to reverse the case), and at the moment the O11D Evo is out of stock anywhere.
@LeonOwO2 жыл бұрын
17:50 ye i have actually seen one with fewer, had to build one for a customer who insisted he didnt want any case fans only a few days ago. cant wait for that pc to catch fire.
@BAWBBAGET Жыл бұрын
Knowing what I know now, having barely finished a 4090 build with a vertical mount from coolermaster, I would not have gotten this case. The bottom mount fan mount especially being on a rail instead of it letting you screw it directly to the case has made the vertical mount installation barely feasible because it’s touching the fans due to the slightly elevated height. Then there’s the fact that online videos have had the old version being demonstrated, providing an inaccurate presentation, notably when taking out the case with just a pull whereas the new version actually has screws attached BEFORE you can pull it off. Ridiculously annoying build.
@dkw01013 жыл бұрын
With an ITX mother board could you hypothetically route the PCIE riser cable behind the motherboard tray? Also would the spacing for vertical gpu work easier with a 360mm set up? It is technically more surface area for the fans
@normustafa872 жыл бұрын
I think a PCIe 4 gen 600mm cable should be long enough to hode behind the motherboard thru the cable management and into the gpu from the inside if you get what i mean
@animalyze7120 Жыл бұрын
Good video, wrong build idea on that GPU. Traditional mount works best in this case and of course I always buy the mesh panels for the front if they offer it. I might splurge and get the newer EVO XL which fixes all these issues and is a nice step up from my lancool II mesh.
@iSEKaiSG2 жыл бұрын
Heyy! Can you wall mount the LianLi O11D Evo? Or do u need a shelf?
@YouDoneDidIt3 жыл бұрын
The plate the gpu is attached to did you flip it around so it's closer to the back panel? The gpu would go deeper into the case instead of sticking so far out. From what I also seen you can put 3 fans behind the gpu if mounted properly. I'd give it a go again with the gpu in that spot again.
@Killshot15 Жыл бұрын
This case is going for about $200 bucks brand new and I just built my first pc but I only paid.$140 for a open box one and it was still perfect and still had all the stickers, didn’t even look touched well worth it.
@Killshot15 Жыл бұрын
Specs Strix 3060ti Msi x570:s max ledge wifi plus 2tb of nvme storage 32 gigs Corsair sl ram
@FriedDoggy3 жыл бұрын
I think a cool theme for a custom loop build would be a a full black build in that case with clear red coolant.
@daviniarobbins9298 Жыл бұрын
Radiator shouldn't be at the bottom of the case with the pump above it. You will have all the air in the pump which is bad. Better to fit the radiator to the roof or the side. Rookie mistake there. Hope you corrected that. Edit: Turn the case upside down. Not ideal but at least then the air will be in the radiator not the pump.
@Garrettdx19883 жыл бұрын
Kyle's ad spot almost convinced me my Barbosol, disposable razor, and Gold Bond combo aren't good enough.
@WorldReserveCurrency2 жыл бұрын
Basically this was the worst build ever due to user error.
@hadoukenocx47463 жыл бұрын
Ah…Bitwit … Kyle ah bro...best setup on this case: bot 3x fans intake, Front mesh 3x fans intake, Top CLC exhaust, Side 3x Fans intake, Back 1xfan exhaust.
@Gladicuss2 жыл бұрын
@BITWIT, Hello and nice to meet you. I just came across your channel and love it. You got your self a new subscriber! Excellent work my friend. I have one question I only trust you with the answer. What AIO water cooling kit would you recommend as being excellent build quality, what all you get with the kit, and how it performs with cooling. I have the same case and another one on the way. Can you please tell me which water cooling complete kit is all around the best kit you came across. Thank you and cheers from Missouri, U.S!
@rory-red3 жыл бұрын
the PCIe riser is so black it blends so well with your motherboard i really didnt see it till you pointed it out.
@dabneyoffermein5952 жыл бұрын
so if this case has its shortcomings, what newer state-of-the-art case can you recommend for me that is a snow white case that is at least a mid-tower (it can be a full tower if necessary for being great build quality). What about the new MASTER COOLER HAF-500? Looks good but cable management might be a bit interesting in the rear area. I'd like something that not loud as hell either. Money is not an issue , I'll pay whatever i have to pay for a case.
@Hangar-zu8xg2 жыл бұрын
Theres shortcomings on the user end more than the case in this instance.
@tylerm.94083 жыл бұрын
When I first saw your completed build I thought you put an ITX motherboard in there, when you pointed out all the empty space at the top I realized that was why!
@shootymcshootjr93383 жыл бұрын
it would be great if you could vertically mount the GPU and still have fans mounted behind it for extra cooling, maybe a bottom mounted bracket instead to stop the GPU from wobbling?
@Matt-gf4gd2 жыл бұрын
You can. At least with water-cooled cards I've seen guys mount a full radiator and fans (slim ones) behind the GPU.
@JoeLeasure3 жыл бұрын
Definitely do a crazy custom build. Maybe try attacking another pcie riser cable to the existing one so you can hide it better somehow.
@F41LZZz3 жыл бұрын
do we really want to see him do one? he's shown an insane amount of incompetence here
@JoeLeasure3 жыл бұрын
@@F41LZZz Ooo, harsh. Yeah, this one was kinda sloppy, but I think he could do a decent custom loop if he spent some time with it.
@F41LZZz3 жыл бұрын
@@JoeLeasure had a look through his builds. the pink and teal one is decent. he is certainly one of the tech youtubers that is where he is now (sub count) because he was one of the first. like jays2cents. they can't be taken seriously
@JoeLeasure3 жыл бұрын
@@F41LZZz Different levels of ability displayed helps people with different levels of ability. I like seeing a whole range myself.
@F41LZZz3 жыл бұрын
@@JoeLeasure hey he's a character, and yeah im with you. he's created a brand, a image for himself and at the end of the day its 'entertainment.' but this was a review. a journlistic bit of material advising customers on a product. a review. his incompetence has shown this case in a unjust light. he has failed his viewers that trust him. why be ok with mediocrity? why defend him? this review was phoned in. it isn't even the bar minimum... testament to that is his pinned top comment
@garyloader14162 жыл бұрын
You're pump which needs to have liquid on it is the highest point in your AIO, When, over time your AIO coolant evaporates your pump will stop working. Fit your rad at the top of the case and you'll not have that problem.
@loots_alots3 жыл бұрын
It might look better with the riser cable coming from the lower card slot, which some MB's run the same speed as the top slot. I guess it's not long enough to route through the back and down to the bottom slot. That said, this still looks like it's in the prototype stage. The space above the MB is big enough for a push and pull radiator setup or a fat radiator, which is a little strange. Just invert it for proper AIO orientation... Duh hehehehe
@Snafu23463 жыл бұрын
So just curious. But I don't even run the side clear panel on my PC's anymore. I just run a open side case. Its a bit more noise but it allows the air to vent out. Also, I often blow out the dust pretty often and I hate taking on and taking off the panel all the time, its not much work, but I just vacuum/blow it out.
@barmanvarn3 жыл бұрын
I'm 5 minutes into this video and had to hit pause as UPS just showed up w/ my Lian Li O11D Dynamic that I ordered a week ago. I'd better not see something in the video that makes me want the EVO more. LOL
@sonbroku16382 жыл бұрын
I have an idea for a watercooled version. Phanteks makes an exhaust distribution plate, mate that with the front glass distro plate replacement, push on a regular 360 rad on side, beefy push pull on bottom rad, standard pull on topside. That being said, with the bottom and sides being push pull with larger rads, do you recommend keeping the tip exhaust as both other rads would be pushpulling intake or would you make side push pull exhaust, with top and bottom intake since I'm making the exhaust fan side a distro plate?
@Bignasty411872 жыл бұрын
I just got my Lian Li and it had no front panel cables attached to it and nothing coming from the power button...we're off to a good start with this build 🤣
@frederickpolk3 жыл бұрын
Let's do an all Lian Li Redemption build with every possible Lian Li product you can throw into it. Except for AIO because it would have to be a custom liquid cooled. Also inverted layout too! Thanks for the video!
@rayndooma56243 жыл бұрын
That Bob Ross comment about my "junk" made me feel like I was personally attacked. Dayum Kyle, why you gotta do me like that LoL
@sparkplugbarrens3 жыл бұрын
GFF Events used 2 thick 360 radiators at the top and bottom and a grafics card with water block in this configuration. Feels like there is some other less stressful way to mount it...
@studog8585853 жыл бұрын
Some good planning and anything is possible
@solusquinto3 жыл бұрын
Just a suggestion ... due to the fact that you can install an 240mm or 360mm Radiator on top in your setup, you shouldn't say "you can't install an Radiator while using the upright GPU bracket" (at min. 21:46). It's only true for the 280mm Radiator but not in general. It's a false claim.
@brianng2132 жыл бұрын
This Evo and the Dynamic. Which is one is better looking? I don't need those extra features. Thank you guys.
@TheSjuris2 жыл бұрын
They are going to look the same. This one is just a little bigger.
@Dugoth3 жыл бұрын
Surprised they didn't let the upright GPU mount also be attached at the bottom instead of the top of the case. That would free up radiator clearance on the top a bit and allow the GPU power to come straight out of the slots at the MB. Would need to create a slot near the front for the PCI-E extension cable though
@SuperHornetX2 жыл бұрын
How would you plug displays into it? You'd need to turn over the case every time.
@Dugoth2 жыл бұрын
@@SuperHornetX The same way they do with the upright mount, it's not mounted flush to the top of the case but using an internal sort of pass through for the monitor cables