Time to Clean up and reassemble this bad boy! Don't quite get all the way through so there will be a part 3!!!!
Пікірлер: 77
@joelvanbruggen90697 ай бұрын
you flew thru installing the jets, and for those of us that are following along, that was a stop and figure it out moment, you also mentioned setting the float height and abra-cadabra! it's its done. that would have been helpful in a video series like this. Thank you for making this video, because it was helpful for the most part, but you skipped a few things.
@jarronmciver2199 Жыл бұрын
this is by far the best rebuild video out there.. a month I have been watching videos of this process and the algorithm just now brought it up. thank you.
@nwmotogarage Жыл бұрын
Yes!! Thank you sir! Glad to see KZbin us putting them out there!!
@austinkrebill308628 күн бұрын
You missed showing the four screw o-rings installation on the mid-body of the carburetor.
@tomatoknuckles Жыл бұрын
These carb uploads are really going to help me build the fcr from my yz426f i took apart about a year ago haha. Thanks for sharing your knowledge with us 🫡
@nwmotogarage Жыл бұрын
So glad you can get so much use!
@tomatoknuckles Жыл бұрын
@NW Moto Garage Have a question for you. In the mid body there's 2 small brass pipes. What are they for because i dropped my mid body and one of them snapped off.?
@nwmotogarage Жыл бұрын
@@tomatoknuckles oh no…. Not good, not good at all. Those help the fuel find it’s way to the top through a vacuum, they are really only air tubes so you might get away with it? I would say you have nothing to loose now so reinstall and see what happens. THE MOST IMPORTANT PART is coming back here to let me know how it goes. But if you need a new carb, I have actually had outstanding luck with the Amazon FCR carbs for only about $150. Tuned and ran just the same as OEM
@tomatoknuckles Жыл бұрын
@NW Moto Garage Thanks for the quick reply man. I was thinking they had something to do with the hot start and choke but makes sense that they deliver fuel. Im going to epoxy it on and give it a try if it doesn't work ill take your advice and get that carb. Thanks again 👍
@rrandydduke2 ай бұрын
If the big seals are coming up short by heating them with a low setting heat gun it will make them grow. Or heat the carb bowl / cover some to the temp that makes the seal fit
@bueller4811 ай бұрын
Maybe I missed it, but what did you use for your "deep clean"? My carb has that same green all over and pretty gummy. Evaporust safe to submerge in...no seals of course. Also, my 4 screws to reattach the float bowl side seem to be too short to grab threads. I even got new OEM screws and same deal. Ideas? Great vids!
@justingeturgun10 ай бұрын
My carb leaks thru the shaft for the accelerator pump. I see you skipped that whole part.
@tonyb19684 ай бұрын
Did you find a solution?
@user-xd7vs1tw3c3 ай бұрын
🤔
@TheFdanyi Жыл бұрын
Best Keihin FCR carb video rebuild, on KZbin
@nwmotogarage Жыл бұрын
Wow holy smokes guy! Thank you!!
@sbz666_4 ай бұрын
@@nwmotogarage He's not joking. Carbs have always felt like a magical creature and you just broke it down bit by bit to the point where I feel like I have a map in my head. Thank you for the great content!
@matthewnorris2033 ай бұрын
What’s your opinion on an ultrasonic cleaner for cleaning carburetors? TOP quality work, sir
@lmtada Жыл бұрын
Excellent videos. Thank You.
@nwmotogarage Жыл бұрын
Of course! Glad I could help
@michaelcotgrave8487 Жыл бұрын
l ordered a new Carb the seat will not seat the needle , love your video remember all to drain carb at end of season , !! will be the best for any toy USE Premium fuel also
@michaelcotgrave8487 Жыл бұрын
the orginal carb on my bike has 172S main and 45 pilot jet , the needle not sure what number didnt check , now the new carb l ordered will come preset with main jet 170/pilot jet 48 not sure of needle # , should this preset jetting be ok or should l go with the orginal factory jettting thanks
@alexflessas9473 ай бұрын
Thank you for the video. How unsafe is grove formation (1/20 of mm ) along slide movement Chanel in the main body?
@alexfann5322 Жыл бұрын
I’ve resorted to this. 06 crf250r and rebuilt everything except the mid body and the needle for the main jet. Bike only runs when all the way lean on the fuel setting and choked. It’s not making sense at all so I think this is the issue
@bryanespinosa70883 ай бұрын
What jets do you recommend on a trx450er I have open lid and full exhaust system? It Boggs out
@tleonard4102 ай бұрын
How/ what did you use to clean up the gunk on the carb
@msaul85 Жыл бұрын
Great video, waiting with bated breath and a JIS screwdriver for part 3!
@nwmotogarage Жыл бұрын
Haha! Love it! Thanks for staying tuned!
@michaelcotgrave8487 Жыл бұрын
@@nwmotogarage ordered a set of proper screwdrivers today
@markpavletich7473 ай бұрын
Unfortunately the road race version of the FCR also has problems. But the bigger issue is nobody makes a replacement for the centre body o ring gasket. If you do know where I can get them please leave a comment.
@markdeeframpton8 ай бұрын
Where did you adjust the float height? My 08 CRF450R owners manual says 6mm but the shop manual says 8mm. Just looking for a source of truth. I will say that 7mm is just about parallel. Split the difference?
@jimmyd1148Ай бұрын
@ 7:37 it appears that I had x4 additional o-rings in the “4 corners” of the mid->main body that you did not appear to either have installed or potentially missed 🫣🤷🏼♂️ Not not picking or being a ass just currently build my new fcr41 mx and I’m using your guide as my bible 🤣🤣🤙🏼🤙🏼
@drew32Ай бұрын
I know right? I saw another mid-body gasket install video on KZbin and he also omitted the 4 o-rings. From what I remember, I think they were in there originally. It's been a while since I tore my FCR apart from stock but I included those 4 o-rings that mount in the screw holes.
@user-tr4pj5dr8v3 ай бұрын
what is the part number for the tire repair kit, thank you
@sbz666_4 ай бұрын
That is a really good warning about the drain plug. I'm constantly taking that thing off to change jets but never though to check it for warping. Definitely doing that next rejetting.
@neiljohnolegario569411 ай бұрын
what happens if i dont put that slide plate in the carb piston ?
@michaelcalderon44017 ай бұрын
Does the pilot jet use a spring? Or is it just the air fuel screw?
@michaelcalderon44017 ай бұрын
Does the rebuild kit come with the o-rings for the fuel line nipple thing 😅
@VitruviunMan Жыл бұрын
Hey man really liking the videos. Keep up the great work!
@nwmotogarage Жыл бұрын
Thanks Ross! That means more than you know! How did you like the different camera angles?
@ianjimenez1097 Жыл бұрын
the best video bro !!! keep up the good work.
@nwmotogarage Жыл бұрын
Aww thanks! That means a lot!
@tommyriesselman4633 Жыл бұрын
Mannn I stripped the second tiny allen, last thing I needed to get before I could fully rebuild my midbody. Spend hours yesterday trying to get it out and now am to the point where it’s impossible. Can you tell me what the smaller gasket under the loop influences? My bike currently doesn’t wanna idle. I’ve tried every size pilot jet and ultrasonic cleaned. Midbody is my last hope for the carb and I stripped the last bolt I needed😢 hoping replacing the other gaskets I can get at and giving it a clean could be the difference still tho🙏🏻
@nwmotogarage Жыл бұрын
Unfortunately I can’t tell you exactly what it does for sure, most likely accelerator pump but if any extra fuel or air is leaking through those seals it will effect your idle.
@smellyuki106811 ай бұрын
could i please have the link for the rebuild kits?
@JeffSongs-zj2es Жыл бұрын
Excellent! Thanks.
@nwmotogarage Жыл бұрын
Of course! New video coming out today!
@alexmorse76365 ай бұрын
What's the grease called
@EDP1 Жыл бұрын
hi this video very great .wel explaned . thanks
@nwmotogarage Жыл бұрын
Thank you! Much appreciated!
@rothvisuals Жыл бұрын
Killin it!
@Wander.Fleaux.Productions3 ай бұрын
It’s WILD the whole mid body is completely omitted from the manual!!! Wtf!!
@ploffan2194 Жыл бұрын
Another video less goo! Keep it up! :)
@nwmotogarage Жыл бұрын
Boy you are so COMMITTED!! I wish KZbin did what Facebook does with “Top Fans” you would earn that badge for sure! Speaking of, have you seen my Facebook page?
@ploffan2194 Жыл бұрын
@@nwmotogarage Dont really use Facebook so no i haven’t. But yeah i really enjoy your videos so ofcourse i’m gonna support them haha😂
@leewilkinson3862 Жыл бұрын
Great video ive got the same carb. My bike won’t idle on its own so I was told to clean carb and jets. I’ve put it back together and now my bike won’t start anyone no?
@nwmotogarage Жыл бұрын
First thing first is to remove the carb again and double check that all of your work you did is still correct, slide plate is correct, your fuel screw has the o-ring on it. Then Reinstall and make sure the hot start and choke isn’t cracked.
@wawanoconer86063 ай бұрын
32 or 38 bro?
@michaelcotgrave8487 Жыл бұрын
is there any way to save the seat for the inlet needle jet , or can one purchase the seat for inlet needle for float, looks like its pressed in , l see the seat has a little damage and will not seal so fuel comes out the over flow tube with float adjusted to 8mm ,thanks for any tips or ideas for my issue yamaha YZ 450 F think a 03 or 04 model year
@nwmotogarage Жыл бұрын
Best bet is to purchase a new needle and hope that fixes it. Those are pressed in and I don’t see a part number for it. You might have to find just the smallest rotary polisher and polish that brass. The tips of those needles are rubber so they are pretty forgiving.
@michaelcotgrave8487 Жыл бұрын
@@nwmotogaragethanks wonder if one can purchase just the mid sections with seat maybe available not sure
@nwmotogarage Жыл бұрын
@@michaelcotgrave8487 unfortunately not, the only way is to buy used or new. I have had good luck with Amazon carbs. They tune the same way and function normally for only $170-180
@michaelcotgrave8487 Жыл бұрын
@@nwmotogarage thanks for the info its really sad one cant change the seat , again thanks for your input , great video for me and all
@nwmotogarage Жыл бұрын
@@michaelcotgrave8487 usually you can, but not on this style. They don’t get damaged really unless someone tries to remove them with pliers or tries to clean it with a screwdriver
@bill5340 Жыл бұрын
What kind of grease and where did you purchase your rebuild parts? Thank you for the great video!
@nwmotogarage Жыл бұрын
Let’s see the grease and all parts I picked up from RockyMountain ATV MC. Free 3 day shipping is hard to beat. The grease is a Seal Grease by RaceTech and the kits are by All Balls Racing. Thanks! Glad you could use the info!
@MichaelSvenson2 ай бұрын
not bad but hard to follow with all the cuts and plz no music at all next time, very hard to concentrate
@alexprics10 сағат бұрын
Clark Christopher Taylor Susan Lopez Donna
@aarzy888 Жыл бұрын
Grate vids.. Sub!
@nwmotogarage Жыл бұрын
That’s awesome! Thank you so much! Glad you were able to get something out of it
@LauraRoss-o8r6 күн бұрын
Martin Helen White Jeffrey Anderson Donald
@DanyAumont Жыл бұрын
you forget 4 orings in your mid body
@rpmerrill16569 ай бұрын
What o rings?
@DanyAumont9 ай бұрын
@@rpmerrill1656 where the screw go there suppose to have o rings