This Is Why You Need The Stahls 360 IQ Hat Press!

[@VincentChoi-d8e]

Thank you for the video. I had to laugh when you talked about putting towels under the hat to give it support, because that's what I was doing. I was getting so frustrated with doing that and still getting scorch lines on my hats. Thanks again for the video and convincing me of what 360 IQ can do and how it's better than the cheap hat press I got off of Amazon.

[@jeffryesmeralda]

Been trying to decide on getting this one or the cheaper options. This was a very good product review. Thank you!

[@esentl]

get this one and don't look back best investment I have ever made as well as the many other shops I know that have bought them, use my affiliate link if you do thanks Jeffry for watching

[@fernandoroybal3968]

How does the Richardson 112 fit on this press?

[@esentl]

awesome watch my videos where I press that hat here kzbin.info/www/bejne/lXvCgIuAbpx3jbc

[@candicealapa7738]

We just ours delivered and had a question on pressure. How do you adjust the pressure? When we adjusted it it gave us an error

[@esentl]

just turn the manual knob

[@candicealapa7738]

@@esentl 🤙🏽🤙🏽🌺 big fans of your videos. You’re the reason why we bought the 360 IQ. Keep doing amazing videos!

[@Buddog33]

I see it’s 10amps. Can it be plugged into standard wall outlet? If not, what’s required electrically to use for home based apparel business?

[@esentl]

this machine runs at 120 volts so 20amp switch 12/2 direct line and breaker is most likely what I would run in a home base setup, I was lucky my home being older I have 20amp breakers in the whole box, use my link to the press if you decide to order helps me out and does not cost you a thing, if you have any other question just reach out via instagram or email

[@Buddog33]

@@esentl great info! Much respect for your videos and apparel. Unfortunately I had already ordered it earlier this week. Rest assured anything I need going forward will be through you. Keep up the great videos and content! Thank you

[@artscreenofhertfordshire4126]

I have this hat press and it does not work good with DTF prints when using the pad.. To make it work I have to remove the pad then I end up with a crease.. Funny though because I see the the manufacturer’s video has the same problem and they blamed the adhesive or lack of it..

[@esentl]

I would think with a DTF transfer which would come off similar to a plastisol transfer I would not use the foam pad... I would maybe try using a thinner silicone pad and up the dwell time....DTF and this press is something I have yet to experiment with

[@artscreenofhertfordshire4126]

@@esentl appreciate the tip could you send me a link to a silicone heat pad so that I can see what it is..

[@mikeferretti7422]

A yr later with this press have you ordered and pressed any of the amazing other patch types stahls offers?

[@esentl]

I have and these videos I have to post still, within the next couple weeks we will be showing some new products

[@VideoProductionsNW]

Great video!! How does it work on beanies. Some of the thicker ones I find my press kind of messes up the sides.

[@esentl]

works great ill be doing a video on that soon

[@VideoProductionsNW]

Looking forward to it!

[@VideoProductionsNW]

@@esentl also, last question, I don’t see any video information on adjusting the pressure, with my GeoKnight I have to adjust the top and move the bottom forward or back to get the pressure perfect and the top and bottom to meet up evenly. Does the bottom move?

[@esentl]

There is a knob on the top that you adjust and the digital display will show the pressure readout, there is no need to adjust the bottom at all

[@VideoProductionsNW]

@@esentl I truly appreciate your reply, I think that just completely sold me on it

[@artscreenofhertfordshire4126]

Didn’t even turn on the press

[@esentl]

there will be a newer video coming soon