Tips on getting your T5 / T6 even lower / adjuster deletes | Transporter HQ

[@aberdeenal3234]

Loving your videos - explains what you do and why you do it - very informative :-)

[@TheOtherGuysUK]

Hole saw through the CV boot.... Chris Howes knows all about that on my van 😂

[@greenyno1]

Great video guys very informative on the lowering front 👍

[@THQAutomotive]

Glad it's helped

[@differentgearuk]

Great Video, would of been good to get some info on the wheel spec and tyre info it’s running also.

[@laurieryoung]

"Would have", not "would of". Other than that, I concur with your comment.

[@PhilRevill]

Great video, brilliant sharing of info. What, if anything, do you do with drop links?

[@ingothebaard129]

Good video! Do you do a rear adjuster delete for vanslams?

[@THQAutomotive]

Ingo The Ba**ard they are a Chinese copy of B14’s so I assume they copied the ID of the rear spring too. The B14 version on our website should work.

[@h12st_d63]

Sorry, to confirm do machine top mounts work on a T28 please?

[@THQAutomotive]

Yes there are the same T26-T32

[@mickyflakes]

Will these deletes fit most coilover kits

[@THQAutomotive]

Most, it depends which coilovers you have

[@petestaveley-hunt9452]

I am on air right now, would you advise to completely remove the front wheel arch plastic liner? When I air out the front wheels hit the liner at the top and pull the liner inwards from the left and right of the wheel. Thanks for any advise you can offer.

[@THQAutomotive]

Hello. No although it is common to kit a chunk away. We would normally cut away the section between 10 o'clock and 2 o'clock. I hope this helps.

[@petestaveley-hunt9452]

@@THQAutomotive that’s great thanks for your insight. Once you cut the arch liner do you need to add screws, sealant etc where the cut marks are to keep the liner in place. Cheers Pete

[@THQAutomotive]

@@petestaveley-hunt9452 No it should still hold in with the original panel clips.

[@petestaveley-hunt9452]

@@THQAutomotive that’s awesome, thanks for your help. Much appreciated 👍😉👏🏻

[@gandhi1078]

Well I understood even if Siri didn’t 😄

[@shaun...6838]

What's the best lowering kit for t32 t5.1 thanks

[@THQAutomotive]

S.d. B14 Komfort’s

[@mattlee8790]

Good video again boys.... the H&R anti roll bars might be an interesting upgrade for the future!?👍🏼

[@sloanieboy1]

Do you still do them shortened drive shafts for t5 vans

[@SteveField]

Great video again! Nice job guys!

[@valentinlyubenov6789]

Can’t wait to bring my t6 to you guys for so low suspensions 😍

[@808bond]

What diameter do you machine the top mount plate down to and which cv boots have you used? Awesome content as always!

[@THQAutomotive]

I don't know the diameter sorry. We have the done by a total machine shop. We use the skinny boots we sell on the website :)

[@peteypops]

Why on earth would you want to lower your suspension? I prefer to be well of the floor…I don’t think ground effect is going to benefit me bombing along at 90kph!

[@THQAutomotive]

@@peteypops because it looks cool as penguin p**s 🐧

[@peteypops]

@@THQAutomotive in that case, worth spending lots of money….

[@THQAutomotive]

@@peteypops 100%

[@CRIDDZ1]

I had a set of so lows fitted to my T5.1 by the THQ crew and it was the best move ive ever made with my van, absolutely love them!! Dont settle for a cheap and cheerful coilover spend that lil extra and get these quality bits of kit!! 🤙🏻🤙🏻🤙🏻 Thanks again THQ!! Awesome video chaps keep them coming.

[@bandiflip]

Hi guys,I know it’s a bit since you did this video,I bought a Bluebird 150mm hub mod kit but can only get 130mm drop on rear even without adjusters…. What can I do to get lower ?? Cheers

[@THQAutomotive]

Hello, no you've done it all if there are no adjusters either.

[@bandiflip]

Thanks for replying…. So I need lower springs then? I’ll go on your website ….. I knew I should of gone air 🤦🏻‍♂️😆

[@richardpage436]

Brilliant video lads. Just simple walk round on a beautiful van 👏👏. Helped me understand what to get 👍

[@vicoadomeit5829]

Can you tell me wheel and tire dimensions? And what rims are these?

[@THQAutomotive]

BBS LM splits. They are around £3500 a set if you can find them. 225/35/19 tyres

[@jimbobthe2ndorthe3rd76]

Is it same ratio for lowering the front in comparison to the rear?

[@THQAutomotive]

No, it'll depend on the wait of the cargo, size of engine, which gearbox, 2WD or 4motion etc

[@soberboy35]

Nice to see the pup featured at the start! Nice work will be in touch about the shallower top mounts 👍🏼

[@Kai77884]

Hello a great video 👍👍👍from Germany 🇩🇪 👋👋👋Kai

[@vwtransportersandmotorcycl3729]

I want that hat 😬

[@THQAutomotive]

We may re-make this colour option. We have lots of others on the website

[@raychambers3646]

Is it true if you can't get it on the ramp at mot station it fails?

[@22Jeffers]

What size hole drill do you need to cut the lip off the hub?

[@danielburton5468]

I wanna get some so lows fitted after lockdown

[@philhodgson4752]

Mikeys van's a peach. 👌

[@martoonf]

What about the drop links? Can I use the oem drop links for my t5 with extreme hub mod and t6 top mounts/ machined top mounts or does it need to be shortened or adjustable?

[@THQAutomotive]

OEM top mounts are correct. You only need longer drop links if you are air suspension low with extra cutting work. Even air and no extra mods would use original length drop links. (Unless its a T6.1, then you need longer T6.1 links)

[@mikenefkens6626]

Great vid guys, thanks. Have you ever had knocking on the rear of a koni low kit? Around the adjusters?

[@mrdeafa25]

You notice how they strategically didnt answer that question?

[@staticyouthuk]

Great video 👍 I currently have a T5 project that I’m going to be running stance+ coilovers and was wondering with regards to the top mount mod can you use the original T5 top mount with the machined down plate? Cheers 🙏

[@THQAutomotive]

No you need the compete T6 kit if you have a T5.

[@edfisher8530]

Hi. I'm of the same thinking as Static. If you aren't resting on the "castle-ations" (great word) of the rubber top mount why do you need the T6 top mount? You are resting the plate on the internal of the top mount. So surely a machined T5 plate would do the same?? Or am I missing something.

[@staticyouthuk]

@@edfisher8530 I used original top mount and cut them down and fitted to my Stance+ coilovers and haven’t had an issue, I have also vlogged it on my page

[@cfkingkong83]

what about wheels aligement adjyst

[@THQAutomotive]

What do you mean sorry?

[@cfkingkong83]

@@THQAutomotive can you make video about aligement of the transporter after solow install

[@THQAutomotive]

@@cfkingkong83 We don't do wheel alignment sorry. We recommend its done 2-3 weeks after installation of any suspension. You want a proper 4 wheel laser alignment.

[@harkingf]

Hello, what make are the wheels on the other van. Do you supply? Thanks

[@THQAutomotive]

The wheels on the white van are BBS LM splits. No we don't supply them.

[@johanschregardus8008]

What are the wheel and tyre sizes under this van? #asking for a friend :P

[@THQAutomotive]

From memory I think they were 225/35/19

[@mercedeslove4291]

Thanks for all the information, really helpful

[@THQAutomotive]

Glad it was useful :)

[@dub8447]

Hi am on stance at the moment but the rear shocks have ran out of travel, are the solow shocks shorter and do you know the closed length please.

[@THQAutomotive]

Yes they are shorter. They are design to be low. Stance aren't.

[@dub8447]

@@THQAutomotive is there any other rear shock absorbers that can be ran low

[@THQAutomotive]

@@dub8447 Gaz and bluebird do a low kit if you are looking for a budget set up.

[@jonashaase2793]

Does Mickey got an Insta ?

[@THQAutomotive]

No sorry, he's a private guy.

[@lukegoodridge-reynolds7920]

I'm new to the vw transport world what would be best coilovers or air ride

[@THQAutomotive]

Personal choice and budget.

[@lukegoodridge-reynolds7920]

@@THQAutomotive OK about 5k budget on air or coilover but I will be using it for family holiday, thanks for the great video keep up the good work

[@theandroidanglers4931]

Hi. How/where can I get hold of a set of shortened drive shafts. #hensteeth.

[@THQAutomotive]

They factory that made them kept getting them wrong so we stopped making them :(

[@theandroidanglers4931]

God damnit . Demand for them must be high right now. Subframe raises being the other option. Would you say they are a straight forward process for mechanics to achieve?.

[@THQAutomotive]

@@theandroidanglers4931 it's not easy. Contact lowdown Transporters

[@bukho2731]

1:02c.