TIPS on how to use gear pullers to remove pulleys and bearings

Рет қаралды 274,530

Күн бұрын

Пікірлер: 55

@hardwarehandtoolsmanufactu3595 3 жыл бұрын

We are bearing puller manufacturer in China and focus on export wholesale. I think this video is very good! It teach many people how to use bearing puller. 👍👍

@perspectivex 4 жыл бұрын

Is there any big advantage of expensive bearing pullers over say the $20 set of three Harbor Freight ones? There are pullers that cost ~10x as much and it's not clear what their benefits are.

@ScottieFredWettstein 3 жыл бұрын

I have a bearing puller that is rated for several thousand lbs and I use an impact gun on it. If you have something truely stuck then a $20 set of three is not going to hold up to a 5' cheater bar or impact gun like an $80 rated puller will. The threads will likely fail on the puller for a cheap one.

@perspectivex 3 жыл бұрын

@@ScottieFredWettstein thank for the reply. I wonder if more expensive pullers also seat themselves more easily. Getting the three legs of cheap ones I got to stay put while I tighten the central rod is really a Sisyphean task.

@adamcolbertmusic Жыл бұрын

@@perspectivexI know this a year later but... I just ordered a cheap set, but I only need it to get the clutch off of a 49cc 5/8" shaft, nothing automotive or industrial. But here's a tip: use a torch on the pulley (or gear or clutch or whatever) where it meets the shaft to make it expand like whenever you run hot water over a stuck jar lid so that you can open it more easily. If the two parts - pulley and shaft - are rusted and therefore fused together, the torch will help break that bond as well. You can also try to drip some Liquid Wrench in there. An idea to keep the jaws held in place is use a large enough rubber band or even wrap some kind of stretchy tape such as electrical tape. I just wanted to share for anyone else who came across this.

@perspectivex Жыл бұрын

@@adamcolbertmusic thanks for the reply. I don't remember my exact problem but I think it was just the jaws always falling off, not that the bearing was stuck. I vaguely remember I tried a rubber band and it didn't help that much but I'm not sure anymore.

@tonyc4776 6 ай бұрын

Harbor freight tools r considered 1 time use tools. I bought solar panel light for my cabin 350 miles away from my house. I went home charged the system it worked perfectly two days later at my cabin sh! T didn't work! 😠. So now I only shop there for the bug racket,

@ken2633 4 жыл бұрын

Shouldn't you shift the bolt/nut on jaw to another holes nearer the job?

@shanh9961 5 жыл бұрын

You lost me when you grabbed your pliers to turn a nut.

@livefree6878 5 жыл бұрын

I can understand that.

@mutantbaby1672 4 жыл бұрын

What size puller should I get for a 7" pulley?

@David-ke9tf 9 ай бұрын

Cual es el presio de los aparatos y donde puedo comprar

@bloomsworkz9093 3 жыл бұрын

Wwhat the size gear puller. How many invhes??

@mrblack9791 2 жыл бұрын

jaw puller a rim?

@mlez7197 2 жыл бұрын

is any grease ok?

@livefree6878 2 жыл бұрын

Any grease is fine. It’s best if you use the same grease each time. There’s a few combinations of grease that react adversely if you mix them. If you’re concerned about mixing grease just wipe off the old stuff and put on anything new. Hope this answers your question

@avishkadilranga2116 3 жыл бұрын

What is the size of the puller

@aldagoc2111 4 жыл бұрын

can i use dat in pulling a motorcycle magneto?

@noneck3099 4 жыл бұрын

....have 3 hands...got it....that would be handy for a lot of stuff actually...

@danielmacias13 3 жыл бұрын

his helper WAS very silent... i thought it more plausible that he has third hand as well!

@markulery2881 4 жыл бұрын

Why don't you show one where it's difficult to take it off and you need to puller

@jairoorellana2087 3 жыл бұрын

Can you use this tool to put back d pulley?

@chadharrison8653 3 жыл бұрын

sure can lol

@karmawalaelectric4988 3 жыл бұрын

Very very nice information bearing puller bro very very good video

@livefree6878 3 жыл бұрын

👍👍

@kevlandy Ай бұрын

I just spent half an hour fighting with a 60yo pulley, when it finally let go I realised the ferocity of the puller had fractured the pulley damper...🤬☹️

@ralphporter6006 2 жыл бұрын

Wow, you make sure you lube the threads but then you use "pliers" to turn it .. LMAO .. Nice catch (Shan H)

@joshthompson1755 4 жыл бұрын

What grease did you use on your threads?

@Steve-mw1hf 4 жыл бұрын

red grease

@itznoah231 4 жыл бұрын

@@Steve-mw1hf you are correct

@slybunda Жыл бұрын

@@Steve-mw1hf is that red rubber grease?

@zackarymeinert2727 3 жыл бұрын

Having a hard time with a pulley, looking for some tips. Otherwise a nice informative video.

@superkleanindia9418 Жыл бұрын

size any one

@jaywealthmechanics9285 3 жыл бұрын

Helpful ♥️

@_DML_ Жыл бұрын

Shearing off bolts on the puller? That's some serious pullage.

@traveller4750 5 жыл бұрын

Bearing puller price

@livefree6878 5 жыл бұрын

Harbor freight sells a set of 3 pullers. The set cost about $20.

@mikekindred5719 4 жыл бұрын

Shannonl,agreed.

@gorilladeathtoem 4 жыл бұрын

Just Google 3 jaw puller. People are so lazy..... The guy already took the time to demonstrate the tool as well as tips and tricks for easy operation. If you can't research the tool you need for the job you definitely shouldn't be doing the job the tool is needed for. Smh. FML.