TKO build guide part 2 - ball storage delete

[@VirginiaRican]

For anyone following along at home, an oscillating multi tool performs wonders on those cuts. Even more precise than a Dremel

[@mekhaiwarsaw4813]

You should sell all the 3d lrinted parts because not many people have 3D Printers

[@BlitzMekanika]

To keep your file in tip top shape, buy a file card. Run it over the file at a 45 degree motion and you’ll clean out all the plastic you’ve filed.

[@calsweeney9116]

Could you use a dremel tool to take off the ball holder?

[@ehdrien1094]

Yup, I was just showing how it could be done without one.

[@calsweeney9116]

@@ehdrien1094 thanks!

[@ferbyclatton8642]

Can you remove this without taking apart the gun?

[@ferbyclatton8642]

I really love my knockout and I am afraid of breaking it, like deathly afraid.

[@magmafalse559]

Kinda Kate but tonight ima try it without taking it apart and eithout any cutting! I’ll update yku

[@WorkDrac]

what screw driver u had

[@tv-pp]

Ball deletion

[@Unthawed_Pie]

looking at these comments you should sell the parts you need for it, you will be making some cash

[@tanktrenchdigger4501]

Hey ehdrien, when setting up the rail part for printing, what side ideally should be laying flat?

[@ehdrien1094]

I print mine standing upright. Front face of the rail on the bed.

[@tanktrenchdigger4501]

@@ehdrien1094 I ended up doing the same through trial and error. Eventually got a good print. Really cool project!

[@pagussoooo]

Hey is there a picitinny rail for rivals? Trying to add a real scope to my sniper.

[@Yacht5.56]

I think they are picitinny attachment capable

[@retromatt2281]

Is there a place where I can buy the 3-d printed rail piece? I wanna remove the storage but I don’t have a 3-d printer

[@protozombie2680]

Do you have thingiverse files to both halves of the jig? There is only one linked in the description.

[@ehdrien1094]

You just mirror it in your slicer to get the other half.

[@protozombie2680]

ehdrien ok thanks

[@kaiserwilhelmii.9076]

Is the ball storage delete needed?

[@ehdrien1094]

No, not really. I just think it looks better. Another bonus is a Knockout will fit much better into smaller holsters if the ball storage is removed.

[@kaiserwilhelmii.9076]

@@ehdrien1094 thanks for replying so fast!

[@travismachado4406]

Is there a way to buy this if we do not have a 3D printer

[@kjmaine17]

One question. how do I get the rail piece for less than the guns value, because i dont have a 3d printer

[@user-np4je9tk7o]

Can you link to the files you use?

[@ehdrien1094]

Link is in the video description.

[@user-np4je9tk7o]

@@ehdrien1094 sorry, I meant what type of files did you use to sand the part.

[@ehdrien1094]

@@user-np4je9tk7o Oh! haha, right. Sorry, I bought those years ago from a local bargain store. I used (the flat side of)a large half round file and a small square file. They don't have any markings on them. They were very cheap but since I'm mostly using them on plastic they've held up fine. Any inexpensive set of files you can buy from Amazon would be of similar quality.

[@user-np4je9tk7o]

@ehdrien Thanks!

[@awesomeman4492]

Where did you get that tac rail?

[@ehdrien1094]

The link is in the description.

[@Super8Dover]

Just a quick question, do we have to use your 3D printed materials? Besides the muzzle piece, what's the purpose of the green pieces?

[@ehdrien1094]

They're a guide for the cuts that I make on the trigger guide. You see me use them at the 11 minute mark.