TL494 100A PWM Controller

In today's video, you will learn how to
make TL494 100A PWM Controller Circuit Diagram using Proteus software.
Plz like share comment into my channel and subscribe to my channel and also press the bell icon to get a new notification.
here is the link for my channel to
subscribe: / betutorial
Circuit Diagram:i.postimg.cc/Q...
How to make TL494 100A PWM Controller using Proteus software.

[@keithking1985]

Nice 👍

[@PatanjaliSamadhi]

😍😍

[@RAVI171175]

Man, very nice work & very helpful too. Keep it up dear & thanks for the very nice video.

[@fifaham]

It is recommended to add seperate resistors at the gate of every MOSFET for obvious reasons.

[@PatanjaliSamadhi]

Ok

[@suryanarayandas1808]

Nice

[@munabhandari2335]

nice video keep it up

[@PatanjaliSamadhi]

Thanks

[@Bianchi77]

Nice video, thanks :)

[@ministeriomundialliberando8403]

Muy buena aportación. Pero seria bueno que hicieras una prueba con carga, por ejemplo, 60A, para ver comportamiento, ya que, con demanda muy baja, puede funcionar bien, mas no así, en el caso inverso. Los spms son muy complejos y la forma de saber su comportamiento es en la practica.

[@PatanjaliSamadhi]

Please write in English

[@ministeriomundialliberando8403]

I'm sorry for writing in spanish. I wrote this: very good explanation. But it would be good if you do a test with load, with 60amp, for example, since with low load, it may works fine but with heavy load it might not. SMPS are very complicated and the only we can its behaviour is during real tests.

[@PatanjaliSamadhi]

Yeah and thank you very much

[@JugalYadav-zm9mc]

NICE

[@theinnovati0nlab782]

Very nice video! Question: How efficient is your design with the paralleled MOSFETs? I am equally working on a high power DC-DC boost converter design. Basically my goal is to design a synchronously controlled interleaved boost converter system - capable of delivering high output currents even at low input voltages. If this works, then I will see about modifying the circuit to operate with synchronous rectification - for better efficiency. Texas instruments did a wonderful job with the TL494 datasheet by explaining all the design considerations and calculations....Switching frequency, power inductor selection, dead-time control, filter capacitor selection.....etc. These will be covered in my next video. Thanks again! The Innovation Lab

[@PatanjaliSamadhi]

Welcome

[@akhtarnadeem621]

Please also make a practical video of this circuit so that we know how it works.

[@PatanjaliSamadhi]

Ok thanks

[@bricedjingol218]

Nice job can i replace bd (139-140) with bc transistor ?

[@PatanjaliSamadhi]

Yes

[@olhodeboi100]

Hi! Thank you for the video. I have 2 questions: 1. Is it possible to make a variable power supply 1-50V with this schematic? 2. Is there a layout for this diagram? Thank you.

[@PatanjaliSamadhi]

Yes, absolutely

[@PatanjaliSamadhi]

this is the invertr circuit after output need to be connected another variable circuit diagram

[@olhodeboi100]

@@PatanjaliSamadhi Sorry for the naive question. What is this circuit supposed to do? I was thinking that it was intended to deliver 1-100V under 100A. Is that correct?

[@PatanjaliSamadhi]

@@olhodeboi100 No it's not that because it has 10-35Volt and 100A

[@anwin85alon]

现在才做啊…

[@marocmaggio1678]

Hi dear, i need the mur120 diode ultrafast, how can i get the library where it is? Can you sens me the link of your libraries or where you have downloaded? Thak you so much!

[@PatanjaliSamadhi]

Thank you very much

[@bricedjingol218]

Bon travail.peut on remplacer bd 149 et bd140

[@PatanjaliSamadhi]

I don'tunderstand

[@hearttouch7528]

bibek bro viral

[@PatanjaliSamadhi]

Thank you

[@maney678]

sir what is name of softwear name plz

[@PatanjaliSamadhi]

It's Proteus

[@fewthings8917]

Hi 👍 is this dc motor controller?

[@PatanjaliSamadhi]

No that is inverter circuit To control any load

[@olhodeboi100]

@@PatanjaliSamadhiWould you please, be more clear about circuit operation. I have build it, using only one IRFP250, just to learn about its basicsfunction. Unfortunately, nothing happened. I thought that whith the 10K trimmer resistor, I could change output voltage from 1 to 50V, under at least 10A.

[@vittalkoppal]

@@PatanjaliSamadhi where's it's Transformer 🤔🥺

[@ahmedalqotaty3691]

thank you bro, can you upload me the schematic file please?

[@PatanjaliSamadhi]

Ok

[@BETEP_BECT]

Артхаус

[@MuhammadYaseen-vx5hw]

Is this software free????

[@PatanjaliSamadhi]

Yeah it's proteus software

[@jtk3983]

👎👎👎👎👎👎👎👎👎👎👎👎👎

[@chetnarayanadhikari3777]

Nice

[@bheshkumaribhandari5935]

Nice