#44 2X PS4 Slim No Power

[@venom3214]

watching this guy fix ps4 power supplies is my new hobbie

[@ToltecMerc]

Do you like PS5 power supply repairs?

[@venom3214]

@@ToltecMerc yes

[@luckywetland]

"He gave his life to take out this power supply" 🤣

[@ToltecMerc]

Brave little roach!

[@Rigamortis81]

Another great video! Yes, more power supply repair!

[@ToltecMerc]

I'm sure there will be more. Just getting into PS5 power supply repair.

[@bojans7445]

Thanks to your explanation I fixed 4 power supplies

[@ToltecMerc]

Nice work! Glad the information helped!

[@mm0077]

Very enjoyable to watch and very informative.

[@ToltecMerc]

Thanks a lot!

[@radwanradwan5894]

Keep going Ilove you man My job same like you ps4 fixing and you help me a lot ❤❤❤❤✅

[@ToltecMerc]

Thank you! May you have many happy repairs!

[@hove131]

Great troubleshooting as always Tolt. I have to ask...what do you do for a living? You're very good at electronic troubleshooting and understanding how these circuits work or do well at learning then through your trial and error testing. Always wondered lol. Great video as usual my friend!

[@ToltecMerc]

I''m a TV Broadcast Engineer. I've been working on electronics for about 35 years. Consoles, about 3 years. Thanks for watching and commenting!

[@hove131]

@@ToltecMerc yea I figured your career had to do with some kind of electrical engineering. You're too smart for it not to have lol.

[@Daveyk021]

I enjoyed you repair of these switching power supplies. Is there a market for used PS4 with the PS5 being what everyone desires these days? I hates roaches with a passion but the repair of the damage they do it fun.

[@ToltecMerc]

There is still some market for PS4 as the PS5 is very expensive and they just are not available everywhere.

[@gamedoctoruruguay]

Why did it only show 12 volts when you plugged in the connector?

[@ToltecMerc]

Because the 12V output has to be enabled. It is normally enabled by the PS4 main motherboard when it is time to turn on. I am manually enabling it with a special cable that has two of the wires connected together. The cable is connecting 4.8V standby voltage to the 12V enable line which caused the 12V part of the supply to start running.

[@PapaGleb]

Another great video. Easily my favorite fixer! Question what’s your most favorite supplier?

[@ToltecMerc]

I love being able to order from Mouser as I can get parts in 2-3 days. Unfortunately, for consoles I usually have to buy from AliExpress and by the time I receive the parts I have forgotten what the parts are for. Thank you!

[@REMEDY-REPAIRS]

Bro u do some amazing work I could never fix any power supply 😭😭😭

[@ToltecMerc]

Never say never! Once you get a basic understanding of switch mode power supplies work, the rest comes much easier! Thanks for watching and commenting.

[@REMEDY-REPAIRS]

@@ToltecMerc U were right I just fixed one with the help of this video 🎉🎉🎉🎉🕺🏾🕺🏾THANK YOU‼️‼️‼️

[@ToltecMerc]

@@REMEDY-REPAIRS excellent! Great job!

[@user-hj2zt9ri6t]

May i know with what I can replace 0.16 ohm resistor, which is impossible for me to obtain. the resistance and wattage of a more common resistor i can find, please.

[@ToltecMerc]

Perhaps you could combine two resistors such as two 0.33 ohm in parallel.

[@MARCSLASH]

The resistor is 16 ohms actually ( 5 bands: brown, blue, white, gold, orange. I've used a 18 Ohms 5 Watts resistor, but with higher tolerance and it worked. If you find a 18 ohms with correct tolerance (+ - 0,05%), 2 or 5 Watts (the original is 2), it should be better.

[@guthi4475]

fault finding and learning is helpful ty.......

[@ToltecMerc]

I'm glad you enjoyed!

[@GearZonom-b6z]

The one on the right in your intro is the one im use to looking at. One of the left is a newer model cause if i remember right the first versions of the slim had a werid power issue.

[@GearZonom-b6z]

I should say revision but still either way you probably know what i mean

[@antwonfleming9076]

Can you tell me what wrong with my game had one come on but I went inside of it

[@PapaGleb]

Have you ever considered making beginner electronics video? I’v always had an interest in electronics but could never get it until recently I tried again and this time things started to click. I got the necessary tools and dove right in learning, reading, watching and practicing but feel I am stuck. Feel like I am missing a key piece that will put the puzzle together and I can’t find that piece.

[@ToltecMerc]

I can't say that I have ever considered making beginner electronics videos. I feel like others have done that many times much better than I ever could.

[@PapaGleb]

@@ToltecMerc You may be right but I have learned that you can hear the same things from 99 people and not get it but that 100th person says the exact same thing and it clicks. Everyone has a different view, mind etc but regardless as long as you are putting content out, I will be here enjoying!

[@OldSkoolF]

what station are you using and what heat are you running?

[@ToltecMerc]

I have a Quick 861DW hot air and a Hakko soldering station. I honestly don't remember what temperature I was using in this video.

[@OldSkoolF]

@@ToltecMerc popped off quick... !

[@yktxhsu]

very good video, thank you for sharing

[@ToltecMerc]

Thank you! I'm glad you liked it!

[@hphp7587]

24:35 Can you give some common replacement for q41? Even better would be voltage and current rating.

[@ToltecMerc]

I believe that part is marked ZEW. It is a PBSS4240T. 40V, 2A NPN transistor.

[@hphp7587]

@@ToltecMerc thats great thanks. Also do you have a schematic of adp-160er? Basically my dnp012 ic blew up and burnt nearby smd. And any alternative ic to dnp012?

[@ajaks7636]

The wonderful world of roaches! Smelly beasts. Great Video and Repairs! Thank you.

[@ToltecMerc]

Thanks so much! I do enjoy bringing them back to life.

[@cristiansantos5742]

video excelente !!

[@ToltecMerc]

Thank you so much!

[@rolilois9897]

Am i stupid, or theres a big fat hole in that chip at 41:30

[@ToltecMerc]

Just a little bit of flux.

[@fajarfirdaus844]

I'm glad to know your video, I have same problem with the PSU, but in my case, I have 5V standby, and when I'm contact to trigger 12V, there is no 12V output, which components do I check?

[@ToltecMerc]

That was the case with this supply. 5V standby was present. It could be the PFC circuit or the 12V generator circuit. There are lot of parts between the two. Start by checking for shorted MOSFETs.

[@fajarfirdaus844]

last I check, there is no shorted MOSFETs, I wanna check DAP049, but I don't have oscilloscope :'

[@MicroMageRepair]

Educational! I think I am probably still going to stay away from PSUs though lol

[@ToltecMerc]

I enjoy power supplies. It's a challenge. Don't be scared of them. Just respect them and you will be fine.

[@bazzi4711]

I came back to this video because i had a similar power supply problem, just like the second model you worked on. Changing the mosfet and resistor had the power supply turn on for me, and i thought the problem was fixed until the next day i found out they were shorted again. I am suspecting the zeiner to be the problem, but looking on another working board that ZD804 beeps normally in continuity mode, which got me really consufed. I am hoping to get a little explanation on that situation and what to do next.

[@bazzi4711]

Update: i noticed the 2R40 resistors were giving different values, i thought maybe they were faulty, and i might fix it by changing them. But, after the change, they gave the same value due to the zeiner diode ZD804 turns out it was shorted. In conclusion, the power supply is fixed yet again, and hopefully, someone will benefit from my comment and notice the little details.

[@ToltecMerc]

Yes, often the zener shorts when the MOSFETs short. Some people may not notice because of the low value resistors in parallel with the zener. You should measure about 1 ohm across them. If you get zero, your zener is shorted. I find it helpful to have a multimeter that lets you zero out your lead resistance. It makes such measurements easier.

[@rfr653]

Good job mate 👍

[@ToltecMerc]

Thank you very much! I appreciate the visit and the comment!

[@dpking3243]

Why can they just make roach proof circuit boards?🤔

[@victoreduardoromanocanizal8221]

QUE PASA SI AL PRECIONAR EJET SUENA Y EL DE POWER NO

[@retropol4316]

Good work i wait for more videos😁

[@ToltecMerc]

Thank you! I am trying!

[@rayancurry]

what could be the problem if my PS4 Slim doenst turn on but the eject button gives sound when pressed?

[@hsp1316]

My psu dap046 is faulty. Can i replace with dap041 as these ic are difficult to source to my country?

[@RasSunfiiyah]

How muxh do you charge on adverge to fix a ps4

[@DoubleBarrelSportsCards]

Good video !!! Keep up the good work !!

[@ToltecMerc]

Thanks Double!

[@Ben-Marzouk-Tarefe76]

Hi do you have any idea about the pro power supply is the same way to tray to activate 12 v to test it witch pin should connect to same time ADP300fr

[@ToltecMerc]

To activate 12V you connect +5V standby to the pin labeled ACDC_STBY. It's labeled on the PCB near the connector.

[@Ben-Marzouk-Tarefe76]

@@ToltecMerc +5v is 5VSB or im wrong .thanks a lot Do you have any ideas about powering the ps4 pro with Xbox 360 power supply

[@Ben-Marzouk-Tarefe76]

@@ToltecMerc thanks a lot for your help

[@guthi4475]

new guy here like how u fault close up so we can see and learn

[@ToltecMerc]

Thanks! I try to show what I'm doing.

[@orion310591RS]

32:03 - In case that you do not have very sharp tweezers, you can use simple paperclip , sharpen it using a sharpening file , then bend last milimeter using pliers. I used this item and cheap usb soldering iron to remove chips without hot air station. Put it under chip leg, and gently press to lift leg.

[@mahmoudhamed559]

i'm a led and lcd tvs tech and good at repairing power supply and motherboard units and i need to go on with playstations and be profissional in repairing them ... Where should i start from?

[@ToltecMerc]

Buy a broken PS4 from eBay and repair it. I would avoid PS4s with the Blue Light of Death problem. Very difficult to repair. You could also just buy some broken PS4 power supplies to start with.

[@mahmoudhamed559]

@@ToltecMerc Thanks a lot

[@cloud1494]

Can I send you my PS 4 with no power for fixing?

[@bojans7445]

hello, I would like to ask if you can help me with the slim power supply and I need it for the PS4 slim 160ER board model and I have R3,R4,R5,R6 burned out I need the values ​​thanks for the answer

[@bojans7445]

board is delta

[@ToltecMerc]

Let me see if I have a 160ER.

[@ToltecMerc]

I believe all 4 are 3.3K.

[@pipassassin1212]

Hi can I use dap041 inplace off ld5760

[@pipassassin1212]

Or dap046 inplace of ld5760

[@ToltecMerc]

I believe a DAP041 should work.

[@victoreduardoromanocanizal8221]

MI PS4 SE APAGA DE REPENTE LUEGO PRECIONO EJET Y SUENA DOS VECES Y LUEGO POWER Y ENCIENDE OTRO RATO

[@Steve_be]

Nice work

[@ToltecMerc]

Thank you very much sir!

[@arthurgomez1941]

i have 20 slim power supply's you want them lmk

[@ToltecMerc]

Sure. Email me at [e-mail]

[@peterbank7694]

Joel much?

[@marcojcardoso2194]

Poderia ter um a tradução dos vídeos, da gringa, para o português.