🔥 Become part of the EG Performance community by joining our Discord server! 🎮🚀 discord.gg/mQsR7CpTng
@TechiePocket14 жыл бұрын
Good video. Ford smashing the keyboard was funny
@chrism.7283 жыл бұрын
Good list, the only thing I would personally change about the this list is swapping out the stock mid-pipe for an offroad H or X-pipe instead of getting a catback. For the auto Mach 1 guys, an aftermarket torque converter to replace the MGW short shifter on this list.
@rygi234 жыл бұрын
A 2.5” diameter x-pipe is the most HP you’ll gain for your dollar. doesn’t matter if it’s with hi-flow cats or no cats you’ll feel a difference starting at mid rpm. Cat backs don’t yield much because the restriction is so far from the engine. Chambered mufflers might get you 5 top-end hp, a straight-through muffler still only yields 8-10 hp and the gain isn’t until your way up in rpm, an X pipe will get you much more, probably around 20. That’s my experience from modding mine.
@kmilli03133 жыл бұрын
CAI looks nice but isnt worth the money unless you just have money to burn. Machs thankfully at least already come with 3.55s so unless you plan on racing or being a little quicker off the line you probably dont need gears, but if you do, minumum 4.10s with the machs higher rev limit. 3.73 isnt much of a change from the 3.55s. Agree on the exhaust, though i have seen videos of stock catback with o/r x and it actually sounds really good! Beautiful mach you guys have!
@truthhurts2283 жыл бұрын
Great video. I too have a 2004 Mach 1 in Competition Orange with the 5 speed manual. I hope this list may help other Mach 1 owners. My Mods are: Ceramic coated headers, Bassani X pipe, high flow cats, SLP shotgun resonators, Magna Flow 3 inch dual stainless exhaust, Ford Racing Stage 2 clutch with Ford racing throwout and pilot shaft bearings. K&N CAI, JDM custom tune, Eibach Street/Strip suspension kit: Lowering coil springs, oversize sway bars with polyurethane bushings throughout, Koni street/strip shocks, Bilstein axle wrap up shocks, strut tower adjustment plates, Carters Customs rear diffuser, Nitto street/track tires, shift light, pillar gauges, B&M short throw ripper shifter, Side and rear louvers , LED upgraded light bulbs for all lights in and on the car, sequenced turn signal lights rear, sub frame connectors, 170 degree thermostat, Ford Racing aluminum drive shaft, Ford OEM Mach 1 mudflaps front and rear (rare!) E3 spark plugs and Accel high performance coil packs on all 8 plugs. It runs like a raped ape and can lay rubber through 4th gear with no problems at all. Enjoy!
@ewalt55013 жыл бұрын
Awesome man! I’m looking to purchase a Mach 1 in the next few months!! I will come back to this video when I’m ready!!
@MrBigdawg814 жыл бұрын
Just got a JLT intake for mine about a month ago
@SynysterGoose Жыл бұрын
That's the car that got me into cars when I was a kid. Comp orange mach 1 and that lead into the Comp cobra.
@michaell63354 жыл бұрын
Great list 👌. Also an off-road x pipe is a must for me lol
@fishsquishguy18334 жыл бұрын
DOHC _ Bang for buck, off-road X is hard to beat.
@wramsey26563 жыл бұрын
@@fishsquishguy1833 I agree on the ORXP did so and kept the stock stainless mufflers, she is plenty loud now with that traditional Mustang sound. Also did the CAI and kept the shaker functional for sure. Did the tuner and boosted the octane a little higher since i can get the 97 oct gas. She runs very good and with only 19k miles i am not going to change her anymore.
@TopMach19 ай бұрын
Put some magnaflows on my Mach1,Diablo tune, i like stock shifter tho
@michaelarkin96784 жыл бұрын
With mine the subframe connectors are much more important then any of these, it just made it handle by making the suspension do the work and stop the unibody from flexing. I make it first, cat-back second, short throw third, clutch cable adjuster and new cable and quadrant fourth, and rear lower control arms fifth. And the list goes on from there...
@zachniverson88163 жыл бұрын
Mach 1s come with subframe connectors from the factory.... GTs and cobras didn't
@michaelarkin96783 жыл бұрын
@@zachniverson8816 Sure. commercial U channel that are screwed in with sheet metal screws, they do nothing to meaningful to help tame the unibody chassis. Get a good set of Maximum Motorsports weld-in ones and feel and hear the difference. No more twisting, creaking and lazy suspension parts. Makes the car so much more fun to drive.
@peterspakosky12432 жыл бұрын
Hell, yes do an extreme mod for Mach 1.
@abhiisnotme3 жыл бұрын
dang i wish i could find an orange mustang, not too many there
@txfishstix54804 жыл бұрын
I can’t believe you left out the Blinker Fluid for +10hp, I can understand some things need to be kept a secret 🤣
@EGPerformance4 жыл бұрын
🤫
@jordanwendell62792 жыл бұрын
4v 4.6 sounds incredible.
@billybrower750 Жыл бұрын
Supercharged is the way to go..car really wakes up
@aaronladwig77864 ай бұрын
Top extreme mods
@joedrew48343 жыл бұрын
got it 2003 Mark one with about 32,000 miles on bought it in 2003 from Hillsboro Ford with a few thousand miles on it maybe 3000 bought it with flow masters and that’s it Just had 4:10 Gears put in it needs a tune
@ApexxPredator13 жыл бұрын
All great mods. Have them all except gears in my Cobra.
@justinweed81118 ай бұрын
4:10 gears are fun in mine but what sucks is you’re doing 3k on the highway if you wanna go anywhere above 60mph
@hexify.3 күн бұрын
just chill in 5th
@porkchopsandwiches192 Жыл бұрын
CAI is a joke but everything else is on point. Great looking car btw.
@theinternets7516 Жыл бұрын
What's the point of removing the intake silencer? Does it improve power or you just prefer the look of the engine bay without it? I've read on forums that it should come out but nobody ever really says why.
@bbelitere2 ай бұрын
So what about the throttle body, is it recommended to keep stock or find something aftermarket ? Bbk has been horrible so far
@EGPerformance2 ай бұрын
Stock is fine
@jonnyvargas9394 Жыл бұрын
Hey bro I need a little help hey how many pins of wires you have on your mass air floor sensor
@andrewwilson9455 Жыл бұрын
Cool car where did u get the coil covers that say mach 1 ?
@SAMPLETEXT2853 жыл бұрын
And the video is sitting at 4.6k views perfect
@mistress3133 жыл бұрын
Number one mod........gears..... Gears........and gears........with. Tuner
@zachgagne3566 Жыл бұрын
Ok so im not trying to brag here or anything but I am curious cause I have an 03 mach 1 and I will start from the front to the end on mods so I have SLP longtube headers with a borla attak catback exhaust system, Tremec T56, stage 2 Mcleod clutch, ford racing aluminum driveshaft, M/T rims, 93 premium race tune from diablo, short throw shifter, and some other goodies but I wanna go for boost but I heard these pistons and rods ARE NOT THE SAME as the Cobra 4.6L engine which would make sense just due to the Mach 1 block being all aluminum and the cobra being cast iron
@thatonemach5064 жыл бұрын
Extreme mods plzz
@LukeGensinger4 жыл бұрын
Performance mod list?.... interior mod list?.... exterior mod list? Pleaseeeeeee I would love that😁 not many Mach 1 KZbin channels
@EGPerformance4 жыл бұрын
Hey we have a 400 wheel hp mod list on the channel. Its based off of our 106400 comp cams. As for interior and exterior, its pretty much stock! But we will be making a updated video of our mods and talking about the whole car in general. Nice comment! Thanks for the support.
@thomaswilliamjohnson30223 жыл бұрын
One thing I never did my brother wanted trade his gears for mine in his ranger definitely should of did it
@EGPerformance3 жыл бұрын
what was the ratio in the ranger?
@thomaswilliamjohnson30223 жыл бұрын
@@EGPerformance 4.10 i hated my third gear it was a drag
@mistress3134 жыл бұрын
I'm running 430 gears in mine.....but I have an Automatic
@wellsyaknow3 жыл бұрын
Do you have any issues with a slipping shift ? Or did have issues ? Did it fix?
@mistress3133 жыл бұрын
Absolutely not .......turn your traction control off........ manual shift from first......and it's a whole different animal.......I ran a 8.70 flat in the 1/8 mile track...... completely stock motor
@pwrshots3 жыл бұрын
i have 4,10's in my converter stalled mach-o-matic. love them.
@greekfrenchman44344 жыл бұрын
Im building dc casting heads for my 98 mark viii atm.... what made you choose the 106400 vs the 106500?
@TheAfroGEEZYack2 жыл бұрын
Are you in san Antonio?
@stunna_CODM3 жыл бұрын
‘12 Boss 302 or Mach 1 and put some $$ into it
@andye55733 жыл бұрын
2012 Boss for sure. It's an all around better car.
@tommymach13013 жыл бұрын
Yes top 5 extreme mods please. What model Bama tuner do you have and did u already have it in use before you cammed ur mach
@EGPerformance3 жыл бұрын
Its the x4 tuner. We got it before the cams, its really good to have.
@tommymach13013 жыл бұрын
Yeah I was thinking about it but honestly what are the big pros of having it if my car only has 4:10 gears jlt intake x pipe with slp loudmouths and short throw how can I benefit from having that I have no engine work done which I want to get cams for it and springs basically the whole top end
@EGPerformance3 жыл бұрын
Its great to have if codes pop up or to clear codes. Just knowing whats going on with the car. Eventually if you want to do some engine mods, you will have the device to load tunes to so the car will run properly
@tommymach13013 жыл бұрын
Well it will be definitely something to look into once I start doing internal mods. I was gonna do the Eaton swap but too much I'd rather just buy a cobra
@theggamer61244 жыл бұрын
Anyone else in here looking for beginners mods for a marauder? I got 12ib 75 shot nos kit exhaust and intake
@theuncluded62204 жыл бұрын
What do you think about putting a set of underdrive pulleys on a mach 1?
@mistress3133 жыл бұрын
I would not recommend underdrive pullys
@theuncluded62203 жыл бұрын
@@mistress313 why not?
@venomsymbiote1783 Жыл бұрын
@@mistress313why not , I was thinking of doing it . What would be the cons ? Thanks
@pippoconte42753 жыл бұрын
what you thin on 2004 mach 1 convertible with 60.000 miles on it and what should lokok for asking price $9000
@EGPerformance3 жыл бұрын
I don’t think mach 1’s came with the convertible option
@pippoconte42753 жыл бұрын
@@EGPerformance ok thank you
@manuelfernandez26163 жыл бұрын
Hi, i have a cuestion; where did you buy the rear wheels 17x10.5? I need to buy the pair. Thanks
@fishsquishguy18333 жыл бұрын
MANUEL FERNANDEZ, AFS Wheels makes Mach 1 replica wheels in a bunch of sizes. You have to check their site often because they sell out and then have a batch made later. AFS used to sell on Ebay Motors also, not sure if they still do. Mach1 Registry Forums in their marketplace was a good place for used ones but I don’t think that site is as active as it used to be. As far as the ASF wheels go: Seems like good quality wheels as far as looks and longevity. Bought a set of 18 x 9 all around for my 03 Mach over 10 years ago. Still look great, subtle but nice. Only thing and I’m sure the 17” are as well, but they’re heavy. Swap em out if I’m going to the track so no big deal. Good luck finding a pair of of the 17x10.5. AFS did have an option of the insets being black rather than grey so just take that into consideration if you’re buying used ones.
@fishsquishguy18333 жыл бұрын
Just checked their site: have a pair of 17x 10.5 in stock for $545. I think most mount a 315 tire on them with no rubbing issues?
@manuelfernandez26163 жыл бұрын
@@fishsquishguy1833 tanks for your answer and for your time
@fishsquishguy18333 жыл бұрын
@@manuelfernandez2616 sure thing dude!
@dbm09163 жыл бұрын
LMR sells staggered sets of mach1 wheels made by SVE.
@TacoSupreem2 жыл бұрын
Did he say a 4:10 gear is higher than a 3:73?
@EGPerformance2 жыл бұрын
the higher the ratio (4.10 gears compared to 3.73 gears) the higher the gearing and the greater number of rotations before the rear wheels turn.