touchscreen panel repair

fix your lilliput/xenarc/whatever touch panel with a lighter and a minute or two (brief video because I was in a hurry - if you don't know what I'm doing, you don't need to do it)

[@healthyjim88]

Worked beautifully without completely disassembling my Garmin nuvi 660. Garmin support said it could not be repaired.. Thank you so much!!!

[@EUEU-2015]

Thank you for the idea. I used similar method with a hair dryer on my car dash head touch screen which was not responsive after dismantling it from the car and took out the resistive glass panel. It worked and save me money from buying a new unit. However need to be careful as too much heat can warp the screen and heating the four sides with the metal strips and pressing the sides work better.

[@Barfotadan]

Thank you! I had managed to dent my Sony TX5 = touchscreen kapputt! Your video inspired me to light a match and put it to my screen. Like magic! It starts working for a couple of seconds. Just enough so i could switch it over to video mode!!! :) So happy right now!

[@sidsingh78]

Wooohooo ...... just repaired two China made 5.7" touchpanels. I ordered two samples for my project and both were DOA. Y axis (Y+ and Y-) showed no resistance in between them. heated both the Y axis conductors on panel with my cigarette lighter and both are working now withing 30 secs flat!!! Useful video. Thanks.

[@codeslayer]

Hey, thank you for the hint. I just saved my Brother PR-600 embroidery machine. It had a faulty touch screen where the upper area just didn't receive any touch signals. During the repairs I used a small crafter heat-gun to warm up the edges and a piece of folded fabric to rub them down. A new touch glass would cost about 120 USD.

[@eesanopi]

Great tip, i used a t-shirt transfer iron to do the job on a konica c252 touch element, its working again after 25 seconds at 230 farenheit.

[@GCS88]

Helped me fix my touch screen car stereo. Thanks!

[@baksosoon]

damn genius, man. i'd buy you a beer if I could

[@Beags68]

Worked great Konica Minolta....Thanks

[@mnetwork]

This video helped so much. My 7" Dynamix screen started acting up a few months ago and I couldn't figure it out. Even swapped out the touchscreen controller with a friend's. The digitizer looked fine. After this video I looked closer and found that the one corner was the tiniest bit raised. I heated up the corner with a blow dryer and and pressed it hard till it cooled. Screen has worked perfect ever since.

[@kunkanitchompunawat7552]

Your video is very helpful to me. Thank you!

[@dev639]

I just made this and it worked! Thanks guy!

[@Demian2514]

Thanks for the tip! I just saved a industrial panel😊

[@mohammadss3339]

I really thank you for the video you shared. It was very helpful. I could repair the Touch screen of my Klasspad calculator. Otherwise, the cost was about $ 60. Good luck to you

[@welltronictouchscreen7464]

WELLTRONIC TECHNOLOGY LIMITED Our products are 4/5 wire resistive touch screen; infrared touch screen; SAW touch screen; touch screen monitor , interactive touch foils, Skype: welltronic-sales Email: [e-mail] Web: www.welltronic.cn

[@hshristov]

Great! Worked for the touchscreen of my microwave too. Thank you so much for sharing!

[@Viking6800]

I sign up an KZbin account just to say "Thank you, Morepickles" it works for me.

[@ALBEYRAMOS]

Excelente.. calente con un blower todo el borde del touch screen y fue una belleza!! deben hacerlo con mucho cuidado... y ya!

[@1621959]

Hairdryer worked for me. Warmed the screen and the right edge buttons which were problematic work fine now.

[@dhoser9296]

Berry, did you remove the screen to do this or leave it in the case?

[@sunnyfpv3694]

Wow! That saved my Kaoss pad! Used a soldering fan

[@jisanislam2230]

its worked brother.Thanks

[@crescentmoon12123]

i love you omg this worked on my Nokia Xpress music sweet jesus thank you

[@miranta89]

works perfectly! just fixed an xperia touchscreen that wouldnt work after a hard fall! thnx a lot!

[@soyelcharmander]

hi, please can you explain what exactly you do? I need to fix a chinese touchscreen, THX a lot.

[@loud1984]

Great! it worked for me too!! thank you!

[@Viking6800]

I sign up an KZbin account just to say "Thank you, Morepickles" It works for me and save my car DVD player

[@kemaxr9]

will it work on tab 3 7.0?

[@skillzz9598]

bravooo. i can waith to test this :)!

[@copiertechexpert2572]

Very useful video

[@JorgePerez-oz2wr]

Funciona Mi teclado M3 korg estaba mal su touchs . hice lo mismo y sirvió ahora esta super gracias amigo ..por tu video

[@Rajeshsai10]

hey how did u connect it to a pc?

[@osamajibril6576]

thank u sooooooooooo much it fixed my tablet thank u

[@tspirit99]

Can you tell me how you linked that up to the screen? i like the way the computer shows the touch screen responding. Hope you can tell me.

[@ipelusic1]

can you tell me witch program use for test touch screen panel ?

[@loud1984]

sure is not a permanent fix, but it worked 4 me. I checked multimeter and found the wire with infinite resistance (maybe you'll need to know the values of working panel), followed it till its border and heated up 4 a few seconds. Now you got to press it with ur fingers (don't use too much strenght, you sure will crack it). If your problem is due to loose contact in the panel, you can fix it this way. Find, before heating randomly the full panel, the side with poor contact and work on it!!

[@elvedinmangafic7161]

can you tell me if you can fix the display for the pa800 that has a stylus

[@nimble1918]

is it necessary to disassemble the glass screen? or can I do it with the glass in place? trying to fix my 2 din car radio. thanks.

[@funny962]

it worked thanks a bunch! :)

[@OnlineHelpNoProblem]

Hey can u tell me what i need to test the screnns at my self thx???

[@luisvidigal3995]

Great video! Can you please tell me which software you used to test the touch panel on your PC and also what board you used to plug it in? Regards

[@kabbamama]

would this work for my coby kyros 7" tablet that has a few cracks, the screen works just not around the areas where the cracks are? please respond asap bc it has been months now i am searching for a replacement and i cannot find any

[@imsween8910]

does this work on all kinds of touch screen lcd?

[@TheMInersShafter]

I have a Coby Kyros MID7034 . Will this work if i kept dropping the tablet and wanted to repair the screen? Its not cracked it just has trouble when i try to touch something on the screen.

[@LordRevan]

hey so i got a xenarc 700tsv. i dont know enough about it. but i know its not working when i try to calibrate it. do you know what could be wrong? it recodnised it and worked (sortof) under windows "flick" drivers but it didnt let me do anything with xenarc drivers. is this what the fix is for? any info would be great!

[@sonnysmith2826]

Would it work for a zeepad 7.0 screen?

[@GraphicFrost]

I have a lilliput owned it for a couple years and I just installed it in my car. The touch stopped working in a few hours. Is this what I need to do to make the touch function work again? It is currently 100% defective.

[@chimeranvampire]

Will this work for a screen on a Kindle Fire?

[@julfiquarali4676]

thanks

[@marcospheitosa]

after warming the touch, did you stretch the plastic with your hands?

[@SuperDroidgeek]

Hi, did u know where can i buy a 4 wire touch screen panel for mid701

[@007R4HM4N]

THNX A LOT BRO! wrkd perfectly bt i did burn my lg viewty screen so it hs a big smal mark but it wrks i thought i wud neva b fixd! thnx

[@Theros2]

GJ, it works

[@srimathim2577]

I need this

[@ericofranco]

will it work for my crashed touch screen? the idea is to melt it together again... thanks

[@darkiefilthyr4395]

can i use a hotair instead of lighter?

[@vanderflussen]

can you explain how it works? i want to do it but i not sure.

[@strayCATchillspot]

if you don't know what I'm doing, you don't need to do it) Category

[@luismera799]

mil gracias lo pude solucionar en una fotocopiadora me anda genial desde argentina gracias

[@johnprime7797]

will it work on g tide pad6?

[@hawlhu]

影片感覺很有趣的說，馬上按個讚的說

[@drumstyx6464]

dealextreme 7" touch panel?

[@ea415]

I have a Thinkpad T410s which came with a touchscreen. I took it off since it makes screen look like grainy. I am planning it to use as a input device. I will connect touch screen to a microcontroller and that microcontroller will connect to laptop as a USB mouse device. I need to know which driver IC is needed to control that touch screen? I dont wanna use the driver in the laptop because that d... Making the story short I need the T410s 's touch screen brand and controller IC name. Thanks.

[@rajat0610]

good one

[@hollyann1890]

how about the screen on a Lowrance HDs 9

[@Ezraph2001]

Is it working on my iView android tablet? It does'nt do anything if i touch something.

[@Luis-xb7zp]

hello I have a envy touchscreen cracked and it is difficult to find this part in that way I can fix this laptop 4111-5 sleekbook touchscreen 14 inches ...can you help me in this to were I can find this piece ?....I been in several places and just have a LCD not this part ..help will really appreciate , thanks

[@tylermcgivney1]

where did you get that panel?

[@rolandsr2728]

What if i have a plastic screen? Will it work on plastic screen? Please answer.

[@InTheFi3lds91]

I need help i have a double din touchscreen cd player, everything works fine its just the screen black out.. What do i do?

[@jocker010101]

Did you tried to use heat gun instead? Use of a lighter seams a bit drastic to me. I need to repair toughbook cf18 screen.

[@cristiandan49]

jocker010101 How do you think about this think? Is usefull or nonusefull? Please give some advices

[@ahmedfarhan3497]

I have a broken touchscreen for my canon printer . What can i do

[@mandreolo]

should it works on the iphone?

[@tiredfingers99]

I see that you heated the outer edge of the touch screen. All there is at this location is two coated traces of conductive silver that are on top of each other creating a capacitive condition. Truly I believe all you really did, without knowing it, was reheat the anisotropic glue containing metal particles where the cable attaches to these traces. What can happen over time is these metal particles in the glue become detached where the cable attaches to these silver traces. Is it possible you can heat near where the cable attaches to the glass next time, and use pressure to make sure these metal particles make contact?

[@vignesh199222]

yes it does

[@Shimmernist]

Dont mean to sound stupid, but would this work on the whole screen? I was wondering so I could just fix the cracks on it? If not I'll try other sites and etc.

[@KiwiSingh]

I had lines on my touch screen before. Now ith has gone all white. Now, when i cool it, the touch screen reappears with the lines, but it messes up after a while. how do i get it back 2 normal?

[@McKack]

@kcard707 DSL touch screen replacements are really cheap so you basically got nothing to lose by trying.

[@bo_day]

is that ds panel?

[@ceteksretek]

i'v got 3 DSlite TS. All wont respond before and after heating.

[@Imetysaw]

does this works for ds?

[@bmradux]

ooh! so that's how they refurbish stuff! with a lighter. :P

[@thomastouber2871]

For korg m3 totaly not!! still search for solution buy already 2 new glasses still same issue black botton on the right

[@cristiandan49]

So, this is the solution? You just put with kind the broken parts of the phone's glass? Please explain me in commentary!

[@daisky86]

thanks it's work out it's amazing regards t

[@pyroguyman096]

Little Caesar's for the win

[@feelipesales]

does it works on ipod touch? :D

[@agroxcraig1012323]

Nice room;p

[@nightwing3443]

how to open a ematic touch screen e8 series

[@rajat0610]

which cable did you use to connect the screen to the computer??

[@user-vz8sz5kf1n]

what if use a program on tablet pc with broken dizitizer which shows about it's touchments? and install it and run with mouse(if only tablet pc allows OTG)

[@uhadme]

Иван Какойнибудевич there are so many types.. manufacturer direct solutions. 3m. com

[@loud1984]

(you can even try to apply a little pressure on each side with the panel connected to controller and to usb to investigate). bye

[@BeeTheRider]

dude I have sony ericsson vivaz and i tried this method,but with touchscreen fixed to the phone. and now my whole touch is not working.. ??? what to do now.. help plzz.z. ASAP..

[@hieldrichs]

Gracias! Sirvió

[@lungraspanta6254]

Can I burn touch screen with the panel [not move digiterzer] ,? I use LCD car my link chevy colorado Thailand.

[@meepyrex]

Perfect on Nokia N97 mini ;-) Touch OK!!!

[@samskeete]

Can you please tell me What software is that you're using on the computer?

[@zaqareemalcolm]

@esnigga people who want perfect eyesight for the rest of their lives

[@osamajibril6576]

could you just put the fire on the tablet screen and make it work

[@MultiKillerontheroad]

how did you connected the touch screen to pc?

[@orange11squares]

+ivan zk using the hdmi output of the tablet to clone the video output.

[@HappyQuailsLC]

Maybe a hair dryer is better?

[@Ramonbiancastelli]

Ola meu amigo. Como você fez isso, aparecer o touch na tela do pc?

[@jmpcampina]

Com um cabo micro-HDMI.

[@bartholameu]

DID THEY SAY IT WAS AN IPHONE?!?!

[@vonrobert6166]

Funcionó en mi korg m50 gracias!!!!

[@elegantmusic1986]

En serio funciona? Algúna recomendación para hacerlo bien?. Gracias.

[@vonrobert6166]

@@elegantmusic1986 sii justo estaba a punto de pedir por ebay la pantalla y no perdía nada con probar, así que desarmé el sínte y funcinó

[@elegantmusic1986]

@@vonrobert6166 me podrías agregar a facebook bro?. Para conversar los detalles. facebook.com/claudio.rojas.piano

[@JorgePerez-oz2wr]

@@elegantmusic1986 Hola una pregunta esto funciona amigo ?