Tower fan cleaning tamil │ how to clean tower fan in tamil │ tower fan cleaning tips tamil │fan

Рет қаралды 36,074

Күн бұрын

Tower fan cleaning tamil │ how to clean tower fan in tamil │ tower fan cleaning tips tamil │fan
Tower Fans for Home
amzn.to/3fT2Tkx
Vacuuming and Greasing the Interior
1.Unplug the fan and watch for the blades to prevent moving. continuously put off the fan before making an attempt to open it.The blades ar sharp and may be quite dangerous. watch for the fan to return to a stop.Leave the fan unplugged therefore it can’t activate whereas you’re cleansing it.
2.Remove the screws holding the fan’s casing along. Check the front and back ends of the fan for a series of screws. Most fans have two to four screws, typically on top of the vent. you may would like a Phillips-head screwdriver. Twist the screws counterclockwise to get rid of them.
The number of screws you would like to get rid of depends on the fan’s build and model.
3.Pull the casing halves apart with a screwdriver. try and separate the halves together with your fingers initial. Grip the highest a part of the case whereas pull the front panel towards you together with your alternative hand. Slide a flat-head screwdriver into the gap between the panels. Work down towards the lowest of the tower, exploitation the screwdriver to any separate the panels.
Some tower fans have a high panel holding the front and back ends along. Pry the highest panel up initial to form loosening the opposite panels easier.
4.Slide the front panel up and off from the tower. Don’t pull the panels away right when you end separating them. The panels attach to 1 another through a handful of plastic tabs that ar terribly straightforward to interrupt. Gently raise the front panel away, feat the opposite panels in situ.If the tabs break, you may have a way harder time fitting the panel back in situ on the tower. Work slowly to avoid damaging the casing.
5.Spray compressed gas into the blade to dislodge dust. Bring the compressed gas canister nozzle near to the highest finish of the fan blades. The blades appear as if a tall, black cylinder that spins within the fan’s casing. begin spraying air into the blades, maintaining steady pressure as you progress the nozzle from aspect to aspect.You do not have to be compelled to take away the fan blades to try to to this. Position the nozzle right on top of the blades and hold it there as you progress it.
Laying the fan down makes the work a touch easier. If your fan includes a stand connected, think about unscrewing it quickly so as to rest the fan on a flat surface.
6.Dust the fan blades with a vacuum brush.Use a brush attachment on a vacuum for the foremost economical thanks to clean off the blades. Brush the cylindrical column of blades, rotating it pro re nata to achieve the opposite sides. Dislodge any remaining dirt within the case.
If you don’t have a vacuum brush use a microfiber fabric.You can additionally use a dirt brush, duster, or once {more}} the fan blades again with more compressed gas.
7.Vacuum up the loose dirt with a hose attachment. Keep the hose close as you sweep out the inner portion of the tower. If you can, flip it on whereas you sweep therefore it picks up most of the loose dirt coming back off the fan blades. Have some other person hold the vacuum hose if required.
If an honest vacuum isn’t obtainable, clean your fan outdoors to stop the dirt and dust from entering into your home. Brush and blow out the fan blades completely.
#TowerFan
#TowerFanCleaningTamil
#DoSomethingNew
8.Spray WD-40 or a material on the fan’s bearings. seek for silver or black rings on the ends of the blade column. they're going to be right on top of the blades, typically on a metal plate securing the blades to the casing. Spray a couple of droplets of the material directly on the ends of every bearing.
If your fan makes loads of noise, the bearings ar presumably the cause. These parts ar liable for spinning the blade column.
WD-40 works well as a brief resolution. For one thing more practical, use automobile grease or white Li grease, obtainable at the most general, home improvement, and machine components stores.
you always don't have to be compelled to take apart the fan’s motor to access these components. However, if you would like to, undo the screws on the highest bearing and therefore the motor at the lowest of the tower. take away the fan blades and motor, then clean them out completely.
9.Reinstall the parts, then take a look at the fan. ensure the bearings and therefore the blade ar wherever they have to be. place them back if you removed them, protection them in situ with screws pro re nata. Reattach the casing, then plug the fan in and let it endure few minutes only.