TP-Link CPE Point to Point Installation and Configuration Tutorial Video

[@HrothlorienGaming]

OMFG You are not only a life saver but also the only one who even started with changing last prefix to 10 and not 254 like the actual instructions say.....Life saver man

[@JohnnyWoodard]

I bought the CPE210 and set up was identical to this. I've been really pleased with the performance. I now have a network extended across a giant field from one house to the other.

[@louiedgomez]

how far is the house from each other?

[@wilfridaj1]

I Installed these for a remote gate without network connectivity. Possibly the easiest hassle-free device. Had network connection as soon as I connected them. Best to setup before taking it to the install site.

[@marijndegen]

Just configured two CPE510 's, posting this comment from my backyard, it all seems to work fine. I'm going to make a connection between my home and my storage area. The other people who are in the storage area can also use the internet, maybe make ask some money a month for the service.. Have a nice day ya'll.

[@ai6mk897]

Awesome hardware and easy to set up. I used for AP (access point) and provides full performance (80+ Mbps) over my back yard

[@socialtrendingstories6597]

So if you buy this devices and set them up you won't have to buy data from ISP

[@MDsaifulIslam-rp5wd]

Range

[@ai6mk897]

@@MDsaifulIslam-rp5wd For point-to-point, I operate 4 HD cameras in our barn, which is ~300m from the house and through some trees in the way. I get very good S/N ratio of ~60dB.

[@rybacksmith2672]

@@ai6mk897 Are the 4 camera's wireless or do they have to be connected to the cpe by ethernet cable?

[@christianhimmler2095]

For everyone who is intressted in this, use a secure connection between AC and Client and not creating a open wifi, as shown.

[@Rob3445]

Hello Christian, could you provide step by step on how to do this please

[@adrianTNT]

@@Rob3445 I will add the solution as a comment.

[@umeshmalik712]

I have ordered the same model today, hope I will configure by steps you shared. Thanks for the video. At my site Distance between 2 devices is not more than 200 Mtr. Installing TP Link to Avoid Fibre cable.

[@pegijeludi]

Work perfect for me...i get optic speed from my friend..100/100 only because lan port on cpe didnt support more

[@adrianTNT]

At 4:16 where it says "security: none" you need to select wpa 2 or wpa 3, because wep and wpa have almost no security, other people can connect but also see your traffic. Wifi networks are scanned in bulk very often, don't assume nobody will reach your network :)

[@TPLINKTECH]

Your right, they are, but WPA3 is not fully adopted yet and this is video is from 2015, so there is about 5 years of dust on it.

[@konstantinoscrete2963]

thanks, i took the 2,4 ghz and works fine. perfect video

[@gagarinone]

Please be aware regarding the (DFS) Dynamic Frequency Selection on 5 GHz. DFS is prioritizing military radar, satellite communication, and weather radar. That means that your link will disconnect between 1-10 minutes if it will find a military radar, satellite communication, and weather radar use in you neighboorhood. The sellers of 5 GHz links, as TP-Link, are talking quietly about this. I had to learn it the hard way.

[@TPLINKTECH]

This is not being quietly spoken about its a nature of the beast. DFS are typically reserved for Radar. To get FCC certification to use the channels are legally required to include such a check and balance to ensure the wireless use is not interfering with said radar.

[@gagarinone]

@@TPLINKTECH You and other companies doesn't inform us customers, when you advertise this products, about DFS. It took me 2 days to understand that it wasn't my setup which were wrong. For any user where stabilty of a WiFi connection is important, any equipment using DFS should not be used.

[@teungroenendijk6638]

Thanks for the video, considering buying these or the CPE210.First question, What UTP cable do I need to extend distance between the poe output of the power adapter and the poe lan0 on the accespoint(Extend to 20 meter)?Second question, What I am missing is the setup between the access point and the modem/router of the internet provider, because I think the access point needz to be in the same IPrange as the IPadress of the router, otherwise the client won't get access to the internet or am I wrong?Thanks for answering. One more question is the software of the CPE510 the same as the type CPE210?

[@workdevice7808]

Perfect. Thank you. Nicely narrated not too fast and all the info I need.

[@kingarthur9539]

Hi, I have a question regarding my setup. Now I own 2 CPE510. I have tried them but the signal is not strong enough to go through trees at a distance of 1.2 km. Now I am thinking of buying another CPE510 and use it as repeater to bypass the trees. My question is. Is the repeater mode in therms of transmission power and not bandwidth as good as a AP? Thank you in advance.

[@Pertamax7-HD]

nice sir

[@alvinelectronicsservicecen3663]

Salamat, idol n kita , walang iwanan hanggng dulo

[@jaybeebartolome4395]

Is this work when there's a building blocking between cpe?

[@TPLINKTECH]

No. you need line of sight.

[@Elias-ee3yp]

Not setting up any equipment, but studying for the CCNA. This is interesting.

[@TPLINKTECH]

Nice, Good luck on your test. Look into the CCNA security test. You can use that test to test or renew for the standard CCNA, also take the test just after the test "resets" This gives you an advantage because both result in a smaller question pool, making passing the test a lot easier.

[@fotisnafpliog7]

How can i set 1 cpe210 as wireless adaptor for hiring internet connection from my neighbour that has not another cpe? Which settings i have to choose?

[@henrikwalfridsson4362]

I bought a CPE510 yesterday. I am only gonna use one of these so I can send WiFi to my neighbor. Wich of the modes am I going to choose?

[@Accumulator1]

How about posting what you did to make it work so others can know , you greedy bastard.

[@gyorgyvajda6559]

How much is the average transfer speed between the two devices if the distance is 2 km over urban area but clear sight between antennas? I see it is 300 Mbps, and the ethernet on it is 100 Mbps. But in a typical scenario, what speed that I can expect in these conditions? Thanks!

[@antoineliu5635]

+György Vajda From my experience, it is 80~90Mbps if the interference is not that strong. U can do a spectrum analysis first to choose a clean wireless channel. Or try to use 20MHz channel bandwidth to get more immune to the interference.

[@tototelpo4389]

This tutorial help me a lot. Thnks TP link good job!

[@Bang-Ben_Tutorial]

thank you very much TP-Link..I use wireless TP-Link CPE210,,speed until 300Mbps it's very good 👍

[@philinnc]

Good video with clear, concise instructions for getting this done. Thanks!

[@DougNYC58]

THANK YOU SO MUCH!!! It worked perfectly!!

[@The_Man734]

Couldn't recommend this video enough

[@TPLINKTECH]

Awesome glad it helps

[@marithan2823]

very best tutorial.... thanks for this

[@eddiemcdiarmid1976]

After some advice. I have a pair of EAP110 outdoor access points. Can I make a point to point bridge between them?

[@kgibson7479]

Does the AP have to stay connected to a computer or can it operate wirelessly after the setup of it and the client?

[@TPLINKTECH]

The AP will need to physically stay connected to the router or switch via Ethernet cable

[@imaeiteen3183]

TP-Link can the receiving end be plugged into a WiFi router so that I can use WiFi instead of Ethernet cables?

[@TPLINKTECH]

@@imaeiteen3183 a router or a AP both would work

[@malteboye1649]

Is it possible to use a normal router as the AP and a single CPE 210 as the client?

[@TPLINKTECH]

No, the reason is that the CPE210 has a very small azimuth that requires unobstructed line of sight. You would need to have two units one as the AP and one as the Client.

[@Tater102]

I am setting up an RV park using these. Can I have 3 clients all pointing back at the access point? Like could they all share the same SSID and have 200 feet between them?

[@Tater102]

I am using the CPE210

[@TPLINKTECH]

@@Tater102 as long as they have line of sight with the main AP they should be able to connect. Though in your situation I would actually recommend the EAP225-Outdoor instead of the CPE210. Using the TP-Link Omada Controller you can wireless Mesh the units to each other They transmit Omni-directional instead of Directional and they operate on both 2.4GHz instead of 5GHz. and using the controller they can all be managed at one time instead of individually. the EAP225-Outdoor has a maximum range of 150 Meters so that would more than suffice for 200 feet between the units.

[@shaheennaryabi8386]

Thank you for sharing great video with perfect explanation. ... I have a problem with my device 2.4GHz High Power Wireless Outdoor CPE as i am getting intreption or in other words disconnection for 5 seconds !!!! any solution ???

[@xingwen1359]

+Shaheen Naryabi What's your detailed topology and problem? Do you mean the CPE lose connection with another CPE or your client devices lose connection with CPE? Please check whether there are any barriers between AP and Client, besides, you can use 'spectrum analyse' under wireless menu and select a cleaner channel to avoid interference. At last, what's the distance between AP and client? Remember to set a distance under wireless menu.

[@techhammad5923]

Few Questions: What is it's range? Its lightening protected? Will it pass signals in the mountainous area? Some barrier?

[@TPLINKTECH]

Hammad This can all be found from the product page of the product on TP-Link.com. Just go to our website search for the model in question and click on specifications.

[@techhammad5923]

@@TPLINKTECH this information is not there, that is why i have asked here

[@TPLINKTECH]

@@techhammad5923 Range and Lighting protection is there. as for the signal it must be unobstructed line of sight.

[@sufiyanshaikh7277]

Bro plz make a video on spectrum analysis how to check and connect best frequency channel with less intereferance

[@TPLINKTECH]

For CPE systems that is very difficult to do. It's not like an Omnidirectional low-power system that is easily influenced but other systems in the area. These systems are high power and very line of sight. The main interference factor is if something obscures the line of sight of the system.

[@RonanGyn]

Hello! I want to distribute my Wi-Fi 120mb down and 10mb up using only one device at home and the friend who lives 300 meters getting full speed on his smartphone. Which products do I have?

[@abhijitbera007]

Any......

[@Qweellz]

Thanks, this help alot! The quick installation guide was utter garbage.

[@gabrielsansar6187]

EXACTLY they are terrible written by geeks with no real world experience or nouse

[@svenRalf]

Thanks for pointing Out the quick Startguide that was beside the toilet Paper in the packaging. Dont eed the Video No more lol

[@chuckb337]

Hi, I have a TP-Link to exclusively communicate with a clients driveway automatic gate. Every 6 weeks I have to go back and open up the gate controller to re-enter the TP-link password, like it has an auto-log off security feature. Real hassle. Is there a configuration to stay logged on/in indefinitely? Thanks

[@TPLINKTECH]

That would be something you would need to troubleshoot with the gate controller manufacturer. A CPE like any AP should keep a device connected, as long as its communicating and in range.

[@chuckb337]

@@TPLINKTECH But as I kinda remember, the Tech who installed the TP asked me when configuring it if I wanted this (log off) feature for security, in case someone outside got inside. Are you certain it is not an option.. I admit it was a while back-cant be sure.

[@TPLINKTECH]

@@chuckb337 No because the channel managers here aren't trained on SMB products. As far as we know in AP mode, the unit shouldn't have any auto-off, There might be a Wifi Schedule option, but that would disable the wireless only during a certain time but that would be based on days. not multiple weeks. there shouldn't be a feature like that. You can reach out to business support [e-mail] to be sure though.

[@CaiZhongwen2023]

nice,wo love TP-LINK,

[@baskeltim4610]

HI Can I use this product to extend my home internet to my business internet cafe? i have 50mbps connection at the moment, but i can upgrade my plan if necessary when i use this...

[@thuggy67]

Yes bro

[@thuggy67]

@@themaxdog extend he said , read properly

[@thuggy67]

@@themaxdog 4 years ago , I don't think he waited on our comments 😭😭😭😂

[@venanciopangilinan1992]

Can I use this as wifi access point for my mobile devices in long range area as well?

[@damasusbagus9123]

no

[@53kt0r]

Quick question: will it worked on an apartment on a 1st floor to connect to a wireless router on a 5th floor (27 meters aprox. clear sight)? if yes, will 2 CPEs be required for it?

[@TPLINKTECH]

No because there would not be line of sight in that situation.

[@53kt0r]

@@TPLINKTECH Just what I thought. Thank you for solving my question.

[@fernandocortez9720]

Excuse my English, I do not know much. I liked your video and some questions came up. The first, can you connect several CPE clients to a single AP? Second, one establishes until which range the signal is established? Third, can it be implemented to access the PCs that the client shares?

[@mohsanadreesadv.]

The Answer is yes, you can connect multiple clients with an ap. Yes you can access the PC's of client side from ap side if DHCP server on both pharos devices is turned off and dynamic IP's are being allocated by one device. Please let me inform if you want to know further.

[@deepakkandangath326]

@@mohsanadreesadv. Can we connect a switch to client cpe... For connecting routers to switch

[@shinkuramaru]

can you allocate like just a few mbps for the access point?

[@TzouPhotography]

All good, but where the first cpe gets the internet from?

[@TPLINKTECH]

Your internet provider.

[@TzouPhotography]

@@TPLINKTECH from the lan port on the Poe ?

[@TPLINKTECH]

@@TzouPhotography Think of the first CPE as any other Access Point it needs to be physically connected via Ethernet to a router or switch connected to your internet source. This can double as a POE source as well if the port is capable or you hook an injector to it as well

[@TzouPhotography]

@@TPLINKTECH Thank you very much!

[@TzouPhotography]

@@TPLINKTECH one more thing, if i do all that, the second cpe ( client ) can give wifi to devices ? And not only by ethernet

[@isaozdemir4140]

I have a TP-Link Archer MR 200 and I haven't a 'Signal Strength' information. What can I do?

[@youssefjebouri3593]

Hi I am using tp wa7210n .. I find a problem when connecting on 802.11n ، Interrupt .. and 802.11g He works with me efficiently ..what's the problem

[@TPLINKTECH]

You would need to reach out to support for that.

[@fayzullojumanov5149]

Hello brother I have a totolink cp900 15km And this tp-link cpe-520 each other will find the wi-fi signal can be connected

[@urospuzovic1009]

Hello , i have a couple questions . 1. Can i use only lan connection from router to AP and configure it from smartphone browser ? 2. Would i have 90%+ internet speed with clear line of sight on 100 meters (150Mbps is speed out of the router) ?

[@TPLINKTECH]

1. Yes you can 2. It depends on multiple factors. Its possible but we can't guarantee speeds

[@oqualcycle]

How do you set up TP-Link CPE to be used as an access point without a computer? Can it be configured via a router and a smartphone at your disposal?

[@TPLINKTECH]

No it will require a device to be physically connected to it.

[@dadimamibebebibi-vlog]

Will this be able to pass through some buildings? Not to tall around 5 floor only and my plan for antenna is on 2nd floor

[@TPLINKTECH]

No. Open line of sight is required.

[@testtest6428]

Hello, To do the point to point it is necessary that the access point are the same, or can do it of TPLINK WA52105 to TL-TL-WA7210N. Thanks You!

[@testtest6428]

nobody knows?

[@ahrfun]

how many clients can be added on single AP

[@owensteve9483]

Question is it possible to make 2 separate nanostation but all are in one location broadcast one Access point as if it was one nanostation?

[@TPLINKTECH]

I wish that was a question I could but it would be best to contact our support team at [e-mail] to get that answered.

[@krazYFaic]

Hi, I'm trying to extend the wifi coverage for a hotel on a budget and I'm wondering if this setup will work: Internet----->Router------>CPE-510---------------->CPE510------>Router------>Access point Router: TL-R480T+ Access point: EAP-220 The hotel has two buildings that is difficult to reach with just ethernet cables hence the CPE. I'm also wondering if you still need a router after the client side CPE or will a switch suffice? Note: More access points and switches will be added to each router once I get it working.

[@quality6779]

yes

[@Hubjeep]

Juan, did you need a second router? Wouldn't the client side CPE plug into a POE switch, and you can plug the EAP-220 into another port of the POE switch? At least that's how I hope it works.

[@DeeCura]

This will work.

[@Hubjeep]

THANKS!

[@DiegoTorresV11]

One thing you can consider is to use the CPE of the 2nd building in its "AP Client Router" mode so you can have a wifi network there. The "Bridge" or "Extender" modes will also do the same job but in the same network.

[@yassineyassine9504]

Hi TP-Link. Thank you for this demonstration, i have a question please. Can i use this Wireless CPE to access my data remotely using cifs and NFS ? Logically the answer seemed o be yes once i have the ability to share the INTERNET and video surveillance. But a friend of mine told me that this CPE is used only for INTERNET sharing and Wireless surveillance.

[@mohsanadreesadv.]

Your friend might be wrong because we are sharing files using this method.

[@yassineyassine9504]

@@mohsanadreesadv. Thank you very much for your feedback.

[@leiftismo2793]

hi there, planning to use WBS 510 for my PTMP setup with 30 clients and CPE 510 as thier receiver, what Omni antenna would you recommend for WBS 510 that can serve within 500M radius client?

[@TPLINKTECH]

I couldn't tell you here. Email [e-mail] and they can answer your question properly.

[@kqabro]

For WISP setup, which APs are recommended, and can it work with third party APs as well. If we use WBS510 as Main AP and connect with WISP mode CPEs?

[@TPLINKTECH]

Depends on your needs. CPE510 is 5GHz and CPE210 is 2.4GHz for Questions regarding specific deployments though we suggest contacting our support team.

[@TPLINKTECH]

@Nikos papadopoylos Depends on your region. www.tp-link.com/us/choose-your-location/ select your region then support then contact technical support

[@vatevor]

How far of a distance would the point to point wifi work? Can the AP and client be 15 km apart?

[@TPLINKTECH]

Depends on the model. You can go to TP-Link.com and look at what is available in your region. You can see the range available in the overview page or in the Datasheet.

[@ThuanNguyen-jn9sp]

can the "client" CPE210 connect to the distant LAN network through RJ45 jack and make 2 different networks one as if they are physically connected?

[@TPLINKTECH]

Client will not create a network. instead you would be able to physically connect a ethernet based AP or router.

[@deccanvintagebritishmotorc6385]

i have an open wifi near my house but icant fix the other pair of CPE on the building from which iam getting open wifi i tried a lot of tricks but the signal till my house is very weak can i fix one pair of CPE and connect it to my wifi router

[@DiyintheGhetto]

What is the range on these devices? I'm looking into it myself but I need to cover a area from point to point.

[@TPLINKTECH]

depends on model. Generally speaking its any where between 10 and 15 KM

[@DiyintheGhetto]

@@TPLINKTECH Straight line to site correct? What about through tress?no buildings or hills anything like that just trees?

[@TPLINKTECH]

@@DiyintheGhetto Yes Straight Line of Sight with no obstructions.

[@waltercardenas7354]

Can I used this device to connect to a wifi network that is 1/2 mile away. Trying to cut down on my expenses. Thanks

[@TPLINKTECH]

Yes that should not be a problem. even on the CPE210 the max range is 5km which is about 3.14 miles. You will need two units though. One at the source and in AP mode and the other at the remote location in Client mode. You will need clear line of sight as these models are all directional based antennas.

[@CBP_tv]

If between two houses we have a big house can connection get through?

[@TPLINKTECH]

not likely. CPEs need a direction and clear line of sight with each other to properly work.

[@vivianbeaton738]

Question: Does CPE 220 is capable of point to multipoint connection? Thank you

[@TPLINKTECH]

It should be but we don't have that product in the US so we can't say yes absolutely. Here is the data sheet though. static.tp-link.com/2020/202003/20200324/CPE%20series-Datasheet.pdf

[@SERVICEPOINT96]

very nice bro

[@MrReivajx]

Hey nice video!. Just 1 doubt. Do I need to add the "security option" by adding a password right? (created on the AP ). Otherwise anyone with a CPE device would be able to get signal from the AP. Is this correct?

[@TPLINKTECH]

That would be accurate for any open network. You would want to secure your network always. With the CPE however a client would need to have line of sight and be within the beamwidth of the CPE to be able to communicate with it.

[@yldrayozayyildiz5876]

teşekkürler çok yarcımcı oldun

[@LSiva93]

How to set up a central Client (Sector / omnidirectional antenna) from where surveillance from 2 or more points can be monitored...

[@TPLINKTECH]

You can't with these products. The CPE products are directional.

[@harisfadillah2898]

wheter all the cables used are "STRAIGHT" type ??? or "CROSS" type ???

[@melvitcardozo8835]

+Haris Fadillah You can use straight RJ45 Ethernet cables for both the CPE510 units.Make sure the cables are long enough to reach the CPE510 unit mounted on poles.

[@niklasmader5043]

can I use the cpe 510 as a normal wlan repeater

[@antoineliu5635]

+Niklas Mäder Not recommend I think, because of its directional antenna:)

[@AlmiraTechId]

+Antoine Federer please me !... Can this tool for point to point connection with a distance of 10 Kilometers?

[@antoineliu5635]

Alditha Nasution I think so. I myself have tried a distance of more than 12km but with a very clear of sight across the sea. You know any obvious obstacles could block the signal thus affecting the distance.

[@kaitogun5801]

can 2,4GHz devices connect to this TP-LINK CPE510 5GHz 300Mbps 13dBi and is it only works for the same tplinkcpe on that video?

[@maria772000]

EXCELLENT! don't know how I would manage if didn't know the language, since I'm Greek but phone service directions here are soo bad!!!!!!!!

[@leopato19]

in model CPE210 its available the "Range Extender" mode too?

[@antoineliu5635]

+leopato19 Yes. It seems to support AP, AP Client Router, WISP, Range Extender, client these modes, which I found on www.tp-link.com/en/products/details/cat-37_CPE510.html#features

[@gianluigiacquaviva2191]

Is it legal in Italy to make this system?

[@an8953]

Hello If I use the Access Point TP-LINK TL-WA801ND_V1 Wireless N300 and use a 2400 WiFi parabolic dish instead of the Omni Directional Antenna, how far can I get the frequency 100% without loss of quality ? ? ? For outdoor long range point to point use.

[@TPLINKTECH]

Can't answer that because that is outside of the products intended use. the WA801ND is an indoor AP not an outdoor one. also the antenna are bound to each other so all antenna have to be the same.

[@iPRINTATHEADVENTURER739]

Hi, is this compatible to other brand(as a client)?

[@TPLINKTECH]

I am not sure. You can reach out to our business support to find out. [e-mail]

[@JohnWhittle]

Any reason why I can't use just one of these to connect to an existing wifi network? Want to extend my neighbors starlink to mine

[@TPLINKTECH]

Because they are Line of sight directional. The source and clients all would need to be within the azimuth of the CPE, which is very narrow.

[@stevepotts4273]

Can I set this up with 3 CPE210 devices. One AP mode, and the other 2 in client mode both set up identical (different device IPs)? They will both be within cone of the AP.

[@TPLINKTECH]

Yes as long at the 2 clients are in line of sight and the beamwidth of the AP. The two clients would then operate like an network adapter on a computer and get an individual IP address. the clients then can each be setup to a separate WAP and provide wireless and wired connect to device in their area.

[@johndungawin7596]

where does the line on the client connected to? Please show where the lines goes on the client side. Thanks

[@TPLINKTECH]

Its simple that would connect to a client device. A PC, an AP, a router, etc. Most would use an AP or router so that multiple clients at the client side can access

[@TiengAnh.Online]

How to align your antenna properly? It seems not like the way you show in this video.

[@AlmiraTechId]

please me !... Can this tool for point to point connection with a distance of 10 Kilometers?

[@allenwu7421]

+Alditha Nasution right, you can do it, it supports up to 15km, www.tp-link.com/en/products/details/cat-37_CPE510.html

[@mahbubislam5231]

+Allen Wu I've been informed it works upto 24km. Am i wrong?

[@skshamim2322]

is it necessary that both device should be at same height ?

[@TPLINKTECH]

They just need to be in the line of sight and in each other's beamwidth.

[@Bamlydean]

Can i use the cpe510 in AP Client Router (WISP Client) mode and connect it to an archer a10 in (Router Mode)? I then want to connect an (AP) or wireless router to the cpe510 so I have an omnidirectional antenna for all my devices at the second location.

[@TPLINKTECH]

The two devices would need to be in line of sight and the beamwidth for that to work. The CPE510 has a very narrow beamwidth. However the EAP225-Outdoor may be a better product for your needs. Its an outdoor Omni-directional AP with a maximum range of 150 Meters.

[@a320homecockpit]

what is the allowed distance between the TPlink CPE and the PoE adapter? is there also a limit on the distance between router port and the PoE adapter? or are this the normal 100 meter limits of ethernet?

[@TPLINKTECH]

As far as we know the limits are that of the Ethernet segment.

[@a320homecockpit]

@@TPLINKTECH thanks but a follow up question arrise then, is the ethernet segment from the router, over the PoE adapter to the device or are these 2 segments (1 segment from router to PoE adapter and 2nd segment from PoE to device. The reason for this question is that I would need to travers first an area without line of sight and then the radio part which has line of sight. The first past is most probable just over 100 meters

[@TPLINKTECH]

@@a320homecockpit You shouldn't have a problem with that as long as the injector is at a location where power can be added. the 2nd segment, ethernet to camera would then have the POE power added to it.

[@birolanlr7632]

I just bought the device dec and there is no Poe ethernet cable to connect between the Poe adapter and the device from the inside of the box. Do I have a color sequence of this cable, if I do it myself, I have knowledge of the cable ethernet.

[@TPLINKTECH]

There is no such thing as POE Ethernet cable. Its just a regular Ethernet cable that power is transmitted down as well. The Ethernet Port does have to be POE capable though. With this device if there is no Ethernet cable any one you have available will work. I recommend Cat5e and up though for gigabit connection capablities

[@Negodaporra88]

Do you Have this Tutorial In Portuguese, And How to Set AP Mode!??

[@indiaindia211]

CAN WE USE TO CONNECT FOR CABLE TV TRANSMISSION ??

[@TPLINKTECH]

No. It is a point to point wireless AP to transmit a signal long distances from a source.

[@Phavouriteinstallations]

Is any wire entering the client cpe?

[@TPLINKTECH]

An Ethernet cable is required for the client side that is typically connected to a router or AP to broadcast wireless to the client side devices

[@bruhaha66]

What is the diameter of the pipe needed for installation?

[@mahbubislam5231]

+bruhaha66 ... It depends your choice :)

[@kashinathharawade990]

hhvrbrjdjf

[@emmettgreen]

I have installed two CPE510 units they connect fine and i have good signal strength. If i send data over the link it works fine but if there is a period of inactivity the link seems to stop working and i have to reboot one of the CPE's. After doing this the link works again until the next period of inactivity. Every morning I need to reboot. Do the units have some sort of sleep mode. Please help.

[@TPLINKTECH]

Honestly not sure on that one. You can email our business support at [e-mail] and they will be able to tell you.

[@gagarinone]

That's happening when the (DFS) Dynamic Frequency Selection, on 5 GHz, is active. DFS is prioritizing military radar, satellite communication, and weather radar. That means that your link will disconnect between 1-10 minutes if it will find a military radar, satellite communication, and weather radar use in you neighboorhood. The sellers of 5 GHz links, as TP-Link, are talking quietly about this. I had to learn it the hard way.

[@chichino5]

is this necessary if it's only an access point setup?

[@TPLINKTECH]

these CPEs are long range directional APs. Technically only one in AP mode would be needed but because the azimuth of the signal is very small it is recommended to have 2 that are able to see each other, one in AP and connected to the source of internet and the Other in Client at the receiving end.

[@chichino5]

@@TPLINKTECH okay. but can I still use just one AP for 200 meters to reach a wifi security camera?

[@TPLINKTECH]

@@chichino5 Only if that camera is line of sight and in the AP's narrow azimuth

[@GebelurenDreyer]

Have difficulties connecting the client to the AP: 1. Do I have to disconnect the LAN cable between PC and AP, to client PC at any time in the configuration process? 2. The SSID network-name. Is that a specific new name for the AP-Client connection, or to the network of the house? 3. At what time may I LAN-connect the AP to the router of the house instead of the PC? How do I do that? 4. What option do I have, if my PC does not have a traditional LAN-socket in the configuration process?

[@TPLINKTECH]

We are not able to provide detailed answer as you are requesting here. You can email support at [e-mail].

[@Lyve613official]

So access point and the client both can be the same CPE

[@TPLINKTECH]

Actually its recommended that they should be. At the very least they have to operate on the same band. Many of our CPEs are only a single band device either being 2.4 or 5 GHz

[@kamrul28]

Hello any one can give some information. How to make wifi hotspots more than 3 km coverage areas and what kind device have to setup please ?

[@ashish06229]

You can buy tenda 03 5 km wireless router . This will cover the range of 5 km. For this you will have to buy two units of tenda router . Configure one unit as Access point mode . And another unit as client mode . Each unit will cost you 3300 rupees .

[@johnielravina8933]

Does this affect latency? Am i gonna be able to play online games and other real time applications with this?

[@TPLINKTECH]

This is a point to point high range product but i would not recommend using it for gaming. There may be times of high latency.

[@johnielravina8933]

@@TPLINKTECH thanks for the response. Im looking for ways to reduce the latency of my home network without having to resort to dsl connections as the isp's in our country is charging outrageously. Do you have any suggestions?

[@tengene__]

Hi with this AP can I connect two client mode in one AP mode?

[@TPLINKTECH]

Sure as long as they all have line of sight and are in the beamwidth of the one set as an AP.

[@JH-wo6zd]

Hi, after setting up client device, is it still need LAN cable connect in client device?

[@TPLINKTECH]

In Client mode think of the CPE as a modem. You would need to connect it to a Router or AP in the Client location to provide that area with the service it receives.

[@singh4881]

sir i create a point to point connection but sir i want to connect a router at client cpe side to share internet on mobile, laptop etc whats its setting

[@St4nley227]

Hi! Is there a french version of this video? Or even a written tutorial?

[@TPLINKTECH]

No unfortunately not. this channel is managed by the US team so all videos will be in English. You can reach out to [e-mail] to see if the French team does though.

[@gagarinone]

You can activate english subtitles and autotranslation to french, then you get french subtitles.

[@edvinas4072]

How receiver antena can work without lan cabel from pc? I want have wifi from receiver antena

[@TPLINKTECH]

Can you explain in detail what you are trying to do?

[@edvinas4072]

@@TPLINKTECH I have router with wifi in my house. I want have same wifi in my garage which is 50meters from my house. I bought two of tplink cpe210, made everything same as in video, one is AP(outside on house wall), and second one is on garage wall as client. Now what next? If I want from client cpe have wifi, so I neec second wifi router in my garage? And I need connect it via LAN cable from client cpe to second router? Is it right?

[@TPLINKTECH]

@@edvinas4072 Yes, you would need an indoor ap or router on the client end to get Wifi in the detached garage. additionally, it would not be the same Wifi as the AP cpe210 is generating the signal and the Client CPE210 is receiving it. If you want the same signal in your garage as in your home look at Deco and pair it with a Deco X50-Outdoor. That should accomplish your needs.

[@TheOmaJohn]

I'm not finding any explanations of the different modes that I find clear. I want to have one in my main building that is used only to communicate with the second, and the second in my outbuilding and running a wireless access point. Can you point me toward documentation that can explain that? The mode descriptions don't seem to be looking at things from the angle I am.

[@TPLINKTECH]

Unit at the main set in AP mode. Remote unit set in Client mode. units must have clear line of sight and be within each other's beam width. If the distance is 150 meters or less consider using a EAP225-Outdoor. you would only need one then.

[@adayinlife101]

Can you use CPE510 as an antenna?

[@TPLINKTECH]

No, While the CPE510 does have a built in radio, it is not capable of being used as just an antenna.