How to get an Old Moped Running/First Things to Check (Compression & Spark Tests, Troubleshooting)

[@gibbstheamazonparrotdenise4628]

Travis, Thank you!!! I have an 85 Trac that has been sitting for a decade. I watched your video and learned a great deal! I WD-40'd cables & moving parts, and shot a few squirts into the spark plug hole. I then sprayed lithium grease on the chains. I turned the engine over by hand as you had done, then used sand paper on the points. After that I air sprayed and sprayed electric connection cleaner on the points and wire connections. Then I cleaned the carb, and sanded the spark plug. It fired up on the 5th kick! I let it run then adjusted the idle. The best news is I am doing 32mph (I weigh 240)!! So again, thank you very much for this video!!

[@mrmadmaxalot]

Just got my first project 'ped. Even though it's not a Puch this video has been a huge help in knowing what I should check. I know KZbin comments can be a disaster (though it doesn't look too bad here, guess moped'ers are good peeps) so I wanted to leave a nice comment and tell you how much I appreciate you making this vid!

[@jdsimons3222]

Thank you, I learned a whole lot watching you go through the steps that I'm taking now with my Tomos A3. First two-stroke, first bike with points. I'm an avid motorcyclist and a home wrench but this older Moped is a great new challenge. Thanks for being so concise and clear for us!

[@TravisTutorial]

Hell yeah! Happy wrenching, the A3 is a great engine but the stock encarwi carb is a little goofy

[@jdsimons3222]

The Dellorto is stock on this one ('91). That much is in great shape at least!

[@antonioshabaka8363]

I finnally fixed the problem. It was tedious. I exposed the whole wiring system. I checked all wires for puncture marks etc. Cleaned all grounds and disconected the taillights. Had a bad connection which inturn burned out the circuit in the connection box. Cleaned and resaltered. Works fine.I changed the design to ensure that it wouldn't happen agin. Thanks alot. You the man....

[@TravisTutorial]

Oh man, glad you sorted it out! Always great to hear how repairs turned out, ride on!

[@mr.inventhor6771]

Crazy how precise you make things, and how far ahead you planned it! Absolute amazing project

[@TravisTutorial]

Thank you! Cheers!

[@ligondeznutz1836]

Thanks a lot travis, used your video to help start and get running my fathers vintage puch that hasn’t run in 30 years, after following the video it ran perfectly.

[@TravisTutorial]

I'm so glad to hear it!

[@jbharsh]

After watching several of your videos I can proudly say that my 1978 puch maxi is running like a top my kids love it thanks guys. And I would like to mention that it was free because he could not figure out how to make it run!!!!!

[@TravisTutorial]

Haha yes! That is the spirit of mopeds, great to hear!!

[@finbah5706]

youre video on Bing carb rebuild was very thorough and close up and slow and I did exactly what you did. It was great. thank you!

[@ricklieffering]

Thanks dude, just what I needed, plain and simple info on how to fix and maintain a moped. Subbed!

[@spacetrucker2952]

I had one bike that the tank was so rusty on the inside that I just took a plastic gas tank off one of my junk riding mowers and made it work. I used an inline fuel filter and shut off valve. It worked great for years.

[@2233golf2]

This soo reminds me to my days as a teenager....being an apprentice in Puch and Zuendapp shop.....You do a very proper job here...way to go...

[@TravisTutorial]

Thank you! That must have been an amazing experience!

[@Escadeus]

omg THANKYOU! picked up a 2009 ssr lazer 5 for 150$ w a rusted gas tank and your vinegar and alcohol tip was essential.

[@ivanhsanchez84]

Thanks for this video,I just bought one over the weekend and have no idea what I'm getting myself into

[@ethangoss1527]

same my older brother bought one at an action and gave it to me for a suprise and i've never messed with two strokes so i had no idea what to do with it

[@SDsailor7]

Did you get your moped running? Cheers

[@ivanhsanchez84]

Did it run for several months and randomly stopped working again. I have to take it back apart and figure why it won't start up again

[@antonioshabaka8363]

Thanks for responding. Looks like I may have do some serious rewiring to do. My bulbs are good. My swithes are cleand and good. Icleaned all ground connections. Checked for pinch points. Everything.... still no luck. Thanks agin. Ill be back at it tomorrow.

[@TravisTutorial]

Ah bummer, it's nice when the fix is easy. The switches are funny...the test for them is to tape the two connectors going into them together and see if it still dies when you hit the brake lever. Obviously the bike can't be ridden like this for safety reasons/no brake light - but even if the switch contacts are good and clean it could still be bad. Beyond scuffing up the grounds with sandpaper I would also look for a simplified Tomos A3 wiring guide on MopedArmy for when you do go to re-wire, less wiring makes troubleshooting e-z!

[@Enroutetwentyseven]

Dude your voice cracks just as much as mine! love it as a deep voiced guy who gets flack for it from time to time. More importantly, I searched a lot after getting a couple very rough Moby's for free and am just getting started. Your videos are concise and easy to follow. Thanks for making good stuff!

[@TravisTutorial]

Glad they are helpful!

[@dylanalbertson5269]

i didnt even notice voice cracks haha, so used to hearing my own crack.

[@goop3213]

Omg!! I had one of those exact models..my aunt gave it to me my last trip to Maine when I was 15 and hauled it back to Kansas... man the thing was a blast!!!

[@TravisTutorial]

Right on! Perfect bike for a 15 year old

[@rickrudge9349]

I've really been enjoying watching your videos. This one especially was done very professionally for an instructional video done alone. You're very knowledgeable, light up, and you edit them very well. Thank you. 👌😜👍🛵🛵

[@TravisTutorial]

You're welcome! I have fun throughout the whole process

[@hartgreen]

Also I really liked your input on the cleaning of the gas tank.

[@submissionsummit]

Bought a 2005 Tomos Targa LX project bike & had no idea how to restore it until now 🙏🏼 thank q

[@jbharsh]

Just got my first moped for free because it didn't run! Watching all your videos. I just got the unsiezed now on to spark!

[@TravisTutorial]

Wooooo!

[@Fjord_Driver]

Supertech oil works just fine. Been running it in my F150 for years and it's pushing 300k miles. Project Farm has done loads of oil and other tests on various brands.

[@BlackthorneBuilds]

I was hoping you'd point out Evaporust! It's the best. I've used it on several bikes. I also really liked your method of removing the kickstand spring! Nice work.

[@BlackthorneBuilds]

@Rob De vogel that's what I was saying.

[@ronalddaub7965]

Years ago I had a flathead V8 in a 53 Ford most cylinders had around 90 a couple had 50 and one or two had 25 lbs per square inch and it was still run a hundred. It was bad valve seats that I could not grind out without doing a complete valve job and on a flat head there is no valve adjustment you have to grind off of the stem or lap it down into the seat

[@segafreak11]

Definitely going to have to use these methods to get my newly acquired mopeds running 😎 CL ad, picked up a ‘75 & ‘85 motobecane roadrunner, and scored an old angel ‘moped II’ for free more or less. Paid $150 for the set of (3) of them :p

[@Chaotic-hg4jl]

I got my 1970 moped from an old chicken house from my fathers land and we replaced the engine but when we first looked inside the gas can there wasn’t any liquid at all inside and I was amazed that it didn’t rust through at all

[@nor4277]

Can you use naval jelly to remove tank rust,and some never dull to clean and polish away surface rust,bikes that sit a long time,you can use stable gas treatment ,so the gas won't turn to varnish.

[@Aldo2m0r04]

I love dell'Orto carburetors... In Italy the most of the old mopeds have this brand of carburetor

[@schirmeyerb]

Yes it is better..! The old model 19..Del orto..with ( guillotine)...was really better...but MIKUNI..Also

[@lilman1796]

Great video travis , great info ,keep up the great work ☆☆☆☆☆☆☆☆☆☆

[@TravisTutorial]

Thanks! More to come!

[@Zack-ot8gz]

I have an 87 Trac Olympic where is the air filter? It runs great, dies going up hills. Front head light isn't working. I think it's running rich.

[@sinaddr1]

This was a great watch - thanks dude! Super informative for a newbie like me.

[@kimdecastro9156]

travis thank you for this video .my story is i found a 1982 honda express out by the curb . it's old and rusty playing a round with it . im new to mophed and how to get them running .

[@kickdrum1185]

I just got a 1979 malaguti commuter II. It has a pedal start and I’m wonder where the battery is. I didn’t see you go over the electrical in this video.

[@JG-Alvarado]

HI! I purchased an old TOMOS STREET MATE last week (yes, from Craigslist) so I can teach myself how to ride before jumping on my other bikes (Yamaha xs400 maxim n Honda Shadow VT700). (I promised my family I'd practice on something "little"). Before I purchased it, I saw the ex-owner ride the heck out of it, kicked it back and off he went, so I loaded it in the back of my sedan and off "I" went! I don't know crap about bikes and I'd like to get it street ready (registered, insured, etc.) by fixing it myself. This little moped has been "suped up" to a 70cc with a different engine, a fancy muffler and ... it has no odometer (?) It has no KEY. I didn't notice that before I got home (oopsie) It's been jury rigged like crazy, but it works like a charm. It has a new battery, the tires are ok, but it has a mess of wires sticking out of the oddest places all jumbled together and placed together with plastic ties. So, where do I start? I'd like to do the work myself given I paid two cents for it. I don't want to start throwing money into it. I'm pretty good with electricity, mechanics and I'm not afraid to get dirty. I cannot tell what year it is cuz the VIN is covered right now by a junk load of jury-rigged wires. I can send you pictures, etc. My question is ... where do I start, what do you suggest and thank you, thank you, thank you for any advice. JG

[@TravisTutorial]

+Janet Grace-Alvarado It sounds like you're off to a pretty good start. That Tomos will have an A55 engine, year will be 2005+. My understanding is the wiring for A55 motors was borrowed from some Chinese scooter and has a lot of extra wires from the factory. If someone has messed with it even further, but everything works (lights, turn signals, horn, etc) I would recommend leaving it. Myrons has a great guide to modern Tomos electrical linked below: www.myronsmopeds.com/category/service/new-tomos-electrical/ The trouble with buying modified mopeds is that most people don't take the time to property tune after installing a 70 kit. If the previous owner didn't reject the carb there is a danger of it seizing from getting too hot. If you only bought it to get comfortable on two wheels, then it's whatever, but if you plan on riding it as a real form of transportation it'd be worth it to read up on performance tuning since modifying a moped from stock has a lot of different variables (torque specs, carb jetting, exhausts, gearing, clutches). At the very least, I'd exercise caution if the stock oil injection system has been left in place, as a 70 kit will keep the RPMs much higher than the stock pump is used to. www.mopedarmy.com/wiki/Category:For_Newbies www.mopedarmy.com/wiki/Category:Performance_Tuning

[@JG-Alvarado]

Thanks SO MUCH, Travis, for your response and links. I am absolutely not going to be riding this as a mode of transportation. It's solely for practicing and getting my footing on something I can handle until I'm completely comfortable. (ride like a pro dot com) I'd rather practice techniques than "go for a spin". I am very thankful for your response and expertise. THANK YOU!!! Brightest Wishes. JG :D

[@TravisTutorial]

Janet Grace-Alvarado No problem! Happy riding

[@0iegocarlos]

hey man, what should I do if the pedal is stuck on the moped and won't move??????? PLZ help

[@jempoof]

Ive got a Peugeot 102 scooter, ive pulled it apart ages ago, to get it painted but then the guy never did.....So im putting it back together. Im struggling on the front wheel! The nuts fit into channels, so you cant spin them. DO you have to assemble them with the forks off then fit the forks? Is it some trick so the bolts never undo?

[@richardgazebien2245]

I have a 1978 Suchs Balboa moped. It was a barn find and has not started in 30 plus years. Question concerning the ignition under the handle bar,. Is that to lock the steering or start the engine? I do not have a key.

[@nunuduta9419]

What kind of spark plugs do they use? I have a malaguti and looks like the same engine

[@jimbo7042]

I got an m48 engine I just changed the head to a high compression head and I couldn't get it to crank. I cut a 1/32 gasket and put it between The Head And the cylinder now it cranks but it doesn't start. Had it running before I installed the head any ideas

[@userbeau]

nice video. I have a puch maxi 77' cleaned the carb multiple times (atomizer and jet are clean, banjo etc..) Cleaned spark plug and checked for spark, fuel flow seems to be good, no rust in the tank. Going to clean the points today to see if that helps. Could be a wiring issue?

[@giovannimoz85]

I did the finger test… it sucks my finger in instead of trying to blow it away. What does this mean

[@xavierhernandez221]

I would love too see a puegoet bike next. Thise things Are sick. I also love puch, but i have a puegot

[@MichaelWarnock-m2h]

Any tips on getting the ignition out

[@harleyconley1010]

I got a 1980 vip garelli moped I’m trying to fix I need more compression any pointers

[@joejojo4751]

Blows your finger off!?! Lol! Man your hard core!

[@mikemiller9535]

Pistol not moving when pedaling. Suggestion?

[@TimODon87]

I look forward to the first start video i just picked up a 77 maxi sport and got it running the carb was clogged

[@rosef6233]

I have a 1978 jc penney swinger 2 and cant get it started. Its in better shape than most I've seen but has been sitting for at least 10 years without running. When I try to start it and kick the pedal the flywheel only rotates 1-2 times, what does that mean?

[@annamoore3430]

I've taken on an '89 Puch that has been sitting in the garage for the past several months, can you show how to do some of the smaller, simple mainenance as well? Starting with changing the engine stop switch? Thanks!

[@arlow11]

hi i bought a suzuki roadie cs50 as a project, it was in pieces , i have cleaned the carb,changed the plug, the petccok is working, the spark seems good,it wont start,if i put easy start in the cylinder it runs for a second, the fuel is 3 months old so im considering changing it..............any ideas

[@WoshJaddell]

I have a 75 garelli eureka but my compression isnt blowing any air out of the spark plug hole when i did the finger test what could my problem be? And also what do i put in the oil tank? What kind of oil do i use. I have a new spark plug that sparks up, i have fuel just no compression

[@tristanlawson3088]

How do u get the cover off the points and stater cover

[@macelius]

Good Vid. Maxi air boxes split too.

[@Chaotic-hg4jl]

We cleaned the carburetor and we have gas flow when we take it out but when we put it back in the flow stops i don’t know if it’s the carburetor itself because it looks clean or if it’s somewhere else

[@MrGosho5]

NGK SPARK PLUGS SAVE THE DAY.

[@abumannocchi8048]

What’s the laws for Philadelphia and Sachs moped.

[@williamrafferty14]

Excellent tutorial - glad I subscribed!

[@neftalilopez4834]

how do i no if acrankshaft bearings are no good can you help me out if the bearing are no good wood it start thank you

[@seasonpolston6358]

I have a hose that goes from one side of the gas take to the other on my 79 Puch moped with a 50ZA engine what is this for?

[@kinkankero]

Question what is the right spark plug for bianchi moped? I run for a little miles and then stopped. Thanks

[@trevorpeery5481]

I'm working on a 70s solo odyssey moped, looking for parts carb, rings , and reed valve

[@brentbartley3448]

I was given a 1980 Sachs Prima moped by my uncle. It has around 2000 miles on it and appears to be in good condition but when I brought it home it would not start. I took it to a local mechanic who had it running/idling well at his shop. He had cleaned the carberator, put fresh mixed fuel in it. I brought it home and took it about a half mile down the street and it quit and I cannot get it running. The mechanic suggested that it may be the crank seals. Any ideas about what I should try?

[@gs6225]

Do you have a video on fixing misfires? I have a newly acquired FreeStyle and 2hp single speed, I find I hear popping at times when the engine is running full speed or when I let off throttle. It does not seem to be very consistent. The unit runs well, thought there is a lot of crud in the tailpipe. All original, accept the float I put in the carb.

[@TravisTutorial]

Popping is usually ignition timing related

[@robertfaust4516]

How do u change the pedal arms

[@fatlaed6251]

I changed my fuel filter and I gave the gas and I got my battery charged I need to know what's wrong with my moped it won't turn over sounds like it wants to but it might not be getting any air

[@salm3604]

Travis, I'm fixing up an old Puch Newport; I noticed it only takes leaded gas. Since you can only buy leaded gasoline today, what do you usually use for fuel?

[@Whydidtheychangeittohandlesnow]

Did all of the spark stuff cleaned the points and the plug and still not getting a spark. Points don’t open as much as yours by the way. It was sparking and running pretty well only a few days ago and suddenly stopped after a ride in foggy weather. If water damage is the problem what do I need? Im thinking of just buying a new ignition coil and spark plug but if it’s a CDI problem idk what I’ll do. I’m so discouraged at this point I’ve done everything I feel confident in managing myself.

[@TravisTutorial]

It is all a learning process :) Let's start with the basics, I would absolutely start with a new spark plug to eliminate that factor. If it was sparking then not, I'm wondering if it is something simple like a loose spark plug boot on the spark plug wire or bad plug. If it is the black bosch coil, it is rare for those to go bad. From here, if you still have no spark I would read up on wiring for spark only, you want to eliminate variables like the horn wiring and kill switch wiring. Best of luck, once you go through the ignition system once it's like riding a bike

[@Whydidtheychangeittohandlesnow]

@@TravisTutorial thanks for the info and here’s the update: I tightened and made sure the boot was fit tight as well as the connection to the ignition coil and all that. Still no spark. I also checked different points for voltage and ultimately decided to get a new ignition coil, cable, boot, and spark plug. I was okay with spending the money for those new parts after testing a bunch. Once I put those in I’ll know if it’s a stator problem or not. Other ppl I’ve talked to agree with me that it’ll probably be that. if that ends up being a problem I’ll get a new stator. I’ll say now I know the kill switch doesn’t work. The lights don’t work either and I think the light switch works because I got voltage when testing those wires at full throttle. I think the stator just doesn’t generate enough electricity for the lights but barely enough for the spark. That’s why I also think the stator finally died on me. Appreciate the help!

[@Whydidtheychangeittohandlesnow]

@@TravisTutorialjust put the new ignition coil, wire for the boot, spark plug, and boot on. Still no spark. Either I did it too quick and wrong or it means the stator needs fixing. Not sure what to do to make sure I replaced the parts correctly but yea there ya go.

[@electrohacker]

you dont want to use carb or brake cleaner on ignition, use contact cleaner, those others can melt the insulation on your coils

[@TravisTutorial]

^ Correct that is the best practice. Carb cleaner is not advised because it can contain oil, brake cleaner is better since it won't but both will eat insulation. Annotation made, thanks.

[@whowho7969]

What about the coil if that’s bad no spark correct?

[@memberson]

This is a very good information. But my scooter is a 2008 Scooter 60 miles on it it's a Chinese scooter. And sometimes it has a habit of hard starts or it sometimes will stall while you're actually writing it. But mainly what is cold I have the hard start problem once it warms up it starts fine

[@scottmorgan5534]

It's alive. Thanks travis

[@TravisTutorial]

+Scott Morgan Hey glad to hear it! Looks like I missed your other comment, apologies - the clutch is usually not a culprit when there are starting problems, more often a cable with too much slack or occasionally the linkage inside the clutch cover needs adjusted but it sounds like you got it sorted

[@robinhedley6535]

jesus ! you just have a Puch Sport with a E50 engine standing in your shed !😅 In Switzerland these things cost an absolutd fortune (+-3000Dollars)

[@sonofthunder4156]

What kind of spark plug wire should I use on my puch maxi?

[@jortiz69mp]

What's the outlet size 10mm or 8mm for your blue puch maxi 300mm extreme shocks ?

[@Ελλάδοςπνεύμα]

hi, is there any chance you can do a video about checking and setting the timing on these two stroke moped engines? Mine has a minarelli v1. many thanks very good and informative video

[@AxellTh]

Some years ago I bought a Suzuki FZ50. After a few weeks one day the exhaustion pipe fell off while riding the moped and the pipe broke. I bought a new one. But after that the moped didnt have much torque when going even slightly up hill. Apart from that it was ok. Havent used the moped for nearly ten years. It has been dripping black oil since then from the back of the exhaust pipe. and the oil tank has also got empty. Would you say this is worth touching?

[@tylerapplegate4332]

So I inherited a 1982 Honda Express. I finally got it started but I have oil leaking from the exhaust. What would be the reason for this?

[@westriverjennin2490]

it’s not oil it’s the gas oil mix and it’s needs to be tighter

[@SDsailor7]

Need a video on how to overhaul the wheel hubs of a moped there is zero videos on YT how how to do that. Thanks!

[@Modinator]

So I have this gilera runner lq, and I bought it for like 100 bucks, it wasnt running, but got it working now, it just does not have a lot of touch in the cvt, I tried with different roles, but could it be the cluth? it looks fine inside, and the sparkplug lookes good, it gets good fuel, and compresion. It just does not pull you forward very well, prob like half a horse power.

[@TravisTutorial]

So assuming that's the 2 stroke flavor of that scooter,- you'll want to make sure the exhaust isn't clogged, that can be a reason you are down on power.

[@Modinator]

@@TravisTutorial it was, there was a heck lot ofn oil down there from the old mix, its got a good mix now

[@charlesfair3382]

My moped is not kick starting the stator is not spinning when kicked

[@ashtanwallace6049]

Just got a 1978 Puch Magnum XK, it was a barn find. I have spark, compression and going to clean the tank. I have the carb apart now and you mentioned the part that holds the float should have a rubber tip, mine does not. Also how did you get the bronze center piece out that the throttle cable goes down into and is I between the floater? Thank you and if you have any more exhaust laying around for sale I may be interested!!

[@TravisTutorial]

Hey-ya! Old comment, but the float needle will need a rubber tip or you'll have leak city. Treatland.tv for the replacement. The atomizer can be removed with a deep 5mm socket.

[@tonjajo73]

puch

[@mordechailevinson8646]

....Thanks for posting this...It was very helpful....

[@fredmcavoy8194]

Hey Travis. I bought a 1983 Vespa moped when the pandemic first hit . Just now thinking about getting a look at it and seeing if it will run. Any advise?

[@TravisTutorial]

Hi there - sure, assuming that is a vespa with pedals, it will have a standard Dellorto SHA carb which came on many different models and is quite easy to clean. Much of the same advice will apply, it will still have ignition points - but it does have a belt and variator instead of a chain, assuming it isn't a single speed Ciao.

[@krishnat8573]

How to engine timing on 2 stroke engine after rebuilding the engine.

[@rabbitprey]

just watched your video for the first time ,excellent.

[@joshualapointe8995]

HI I'm going through A motori Minerelli. not sure of year. I am not getting spark when I hold the plug to the head, but when I remove the plug and just hold the wire to the head I do see spark. Any tips? Also there is no taillight hooked up not sure if that matters. I am holding just the start lever when checking spark. is that correct? Thanks for any input.

[@TravisTutorial]

You have tried a second spark plug right? Just want to check (had that happen to me once...). If that isn't it, most likely a corroded spark plug boot. Treatland.tv sells a super nice NGK boot with a rubber end piece to help keep out water for less than $5, I usually just replace. *Some* Italian mopeds have the brake or tail light hooked up through the ignition coil, but if get spark at the head then that's likely not a factor here. You may find once the bike is running the brake levers will kill the motor. And yes, sounds like you are checking for spark correctly!

[@ownerfate]

I may give these a try, i have an old 77 tomos i wanna try to get running again.

[@Mongoose118]

I thought you had to put a little oil in the plug hole, for a compression test

[@mikeworrell8141]

Hey Travis I'm working on a 79 Indian...piece of shit I know but I was following your video and I got held up at the ignition points..i can rotate the fly wheel but the points don't move at all...i can move them with a screwdriver but will cleaning them really allow them to move feely?

[@saiconicfitness]

Can you make a video on how to charge the battery of a laser 5 SSR moped ?

[@TravisTutorial]

+Saidia Manyuan (Globetrotter5K) Unfortunately I don't spend much time around newer bikes, but it appears that the battery will be under the right side cover. If you dig around on KZbin you should be able to find a video on charging scooter or motorcycle batteries, sorry I couldn't be of more help!

[@saiconicfitness]

TravisTutorial OK; thanks.

[@tolltone1181]

i baught a 1970,s or 80,s honda spree for 40 bucks like 4 years ago and it ran great untill last summer, i checked the compression, fuel lines, oil, cleaned the carb, replaced air filter, and cleaned all the electric connections and it still does not run. any advice you can give me?

[@tolltone1181]

Toll Tone its the same one you made a video on but the dash is different and mine is black with the spree on the side being purple.......i didnt see that video untill after i posted the comment above lol sorry.

[@SirCharles.]

you think maybe you can't get over 90psi on that one puch could be because it's tapping the Schrader valve, being a high comp head and all.. I noticed you have a vespa si, I have a ciao with problems, cylinder is free but there's a rough patch during rotation, do you know what this could be and why it's keeping my motor from running?

[@lincolnlunt6678]

what is the moped brand and model i have the same one and need parts for it. Please i need help!

[@antonioshabaka8363]

I have a 1984 tomos. When I pull the break lever the bike cuts could you tell me how to fix it.

[@TravisTutorial]

I've had this happen on a few bikes, first thing to check is your brake light bulb, if that is not blown then you could have a bad switch (screws into your controls and has a small button that is pushed/released when the brake lever is open). The last likely thing it could be is a bad ground somewhere.

[@tenere_surfs5164]

Thx for the video, i have a few questions, checked the compression spark and timing. Also cleaned the carb, but stil the Puch doesnt run. The spark plug gets wet really fast and when I tried to start it Thérèse is a littekens bit of smoke coming from the exhaust. What could the probleem be?

[@williamrafferty14]

Hi, did you ever get this sorted out - mine is the same?

[@tenere_surfs5164]

I bought a carb revision kit, this worked. The sealings were the problem i guess

[@williamrafferty14]

@@tenere_surfs5164 Many thanks for the swift response - I will definitely try that. Here’s, Will.

[@hartgreen]

Ok so Travis I could hug you. Im on my very first project and I needed this video. I bought two mopeds for $450. A Moto Guzzi Robin and a Pacer Super sport. I could only keep one so I sold the Moto Guzzi that was running by the way but it didn't have that awesome top tank. Now Im taking that money and plunking it in to the pacer that wasn't running, good or bad. I didn't watch this video (kicking myself) before I started to tear in to the Pacer. I was very meticulous about bagging and labeling all the screws and so forth so getting this back together will be pretty easy. I have several issues. First when I took the head off I noticed that the cylinder had a lot of burnt crud all over it. (I will check for scoring thanks to your video) Is that something I can clean? or do I replace the cylinder? Next question. Do you know anything about the Morini M01 engine? If so how do you check the points? I cant seem to see them through the fly wheel.

[@TravisTutorial]

I would say you made the right choice! The M01 is a better motor than the G2 motor on the Moto Guzzi to start out with. As far as the cylinder, carbon buildup is pretty normal because all two strokes are just dirty, plus the oil they had back in the day was pretty crude, so long it wasn't seized it is probably fine. I had an M01 on a Bianchi moped a few years ago, fairly robust little motor. Italian mopeds always have little bitty flywheel windows, you'll have to really fiddle with it, but you should be able to check/adjust without having to buy a flywheel puller.

[@VintageMopeds]

hi Travis great vid

[@jeffreymonahan9000]

Hey great videos! I have a puch maxi and I don't know if its getting gas.. when petcock is in the on position nothing drips out ? Does it need replaced? Or is it vacuum operated?

[@TravisTutorial]

100% Gravity - Petcock could definitely be clogged, you could take it apart since they're pretty simple, or you could replace, the "puch maxi gold petcock" on Treatland.tv is a fine replacement. If you take the petcock off and gas comes pouring out make sure it's clear and free of debris.

[@jeffreymonahan9000]

Great! I ordered a new petcock I hope that does the trick. I subscribed to your channel btw. Keep up the great work!

[@JacobChamness23]

My thumb was blown off. Now I’m missing a thumb.

[@nor4277]

Wow you got your work cut out for you,I would love to see this one when you are done with it ,I would love to own one these,I like better than scooters,do they make a lot of after market parts for these,to speed them up a little,like after market exhaust and carbs,bigger piston

[@TheStandoff015]

Can you please make a video about how to wire lights on your puch?