Tronxy VEHO-600 Diy Large Direct Drive 3D Printer Installation Guide Video

How to install Tronxy new type VEHO-600 Diy Large Direct Drive 3D Printer Step by Step. Please check the installation guaide video.
We have newly launched 600 series brand new --VEHO-600
Large Size Direct Drive 3D Printer 600mm*600mm*600mm
●Super large buiding size 600mm*600mm*600mm
●The heated bed upgrade to the silicone heated bed
● 20 PIN integrated cable Tidy Printer head
● PEI heated bed plate
● Large Fixed foot cup & Three Tie Rod on the outframe
● Automatic left and right leveling function Newly in firmware
● Dual-axis OSG guide railway
● Large Fixed foot cup & Reinforce cross braces
● Proximal feeding BMG extruder for Flexible Filaments
VEHO-600 link:
store.tronxy.c...
#3d
#3dprinter
#3dprints
#budget3dprinter
#3d printer
#3dprinting
#3dprinter
#fast3dprinter
#fast
#large format printers
#Best 3D printer for large prints
#Large print area 3D printer
#large3dprinter
#largesize3dprinter
#largescale3dprinter
#largeformat3dprinting
#largebuildvolume3dprinter
#largesize3dprinter
#largebuild3dprinter
#largescale3dprinter
#large3dprinter
#largevolume3dprinter
#large3dprinter
#largeprinter
#largesizecorexyprinter

[@FilamentStories]

This is a great installation guide video to accompany people as they build the VEHO-600. It moves quickly and isn’t too slow but it has all the steps clearly shown. Nice work, Tronxy!

[@Tronxy3DPrinter]

Thanks for your good praise. Your affirmation is the motivation for us to move forward.

[@learnMax]

Very interesting! I just started using my X5SA-pro 400 and can say that I love it and TronXY has been getting a bad rap! Things may have been quirky with older models in the past, but this thing is super rigid and prints very well, and very quickly! If you need more reviews, I'd love to take a look a the larger models, but I'm set with purchases for a bit (and I'd gladly find the space for that 600mm printer!)

[@josipsarkanj9065]

The arrangement of the cables would be nice if they were also used on smaller printers...XA5Sa and others

[@Tronxy3DPrinter]

Thanks for you good advise. Our engineer team are working on it to update our X5SA other series. Many thanks.

[@Raulmiro101]

Hello, I just bought a veho600 3d printer and a bearing 2 doesn't fit the screw rod ( one was a FL000 code and one with a FL001) FL001 fits Any tips? Is it me u is failing or did they sent the wrong part?

[@PaganWizard]

I would love to do a review on your VEHO-600-2E 110v

[@Tronxy3DPrinter]

Hi ，you can sent a email to [e-mail] to talk the cooperation if you have some channal or some influence of social media

[@Sandtypboy]

2 quick questions : 1. When i try to install the z-stops it wont go down to the z-stops at all. It gets the x- and y points but goes down for about 10cm not more. Should i go down by hand or is that wrong at all? 2. Even if the sensor turn red the maschin wont stop. Why is that?

[@Tronxy3DPrinter]

1. The Z-axis photoelectric switch may not be properly installed, causing the platform to stop far from the nozzle. Please check 2. The leveling device is only used for leveling and does not serve as a Z-axis limit You can contact us for specific after-sales service: [e-mail]

[@brianmadonna2873]

Is really as easy as the video to assemble?

[@Lakistrikee]

Почему кинематика Кортезиан? Обьясните почему отказались от CoreXY? Какие доводы?

[@josipsarkanj9065]

At this price and size, the printer could easily have a ballscrew

[@Tronxy3DPrinter]

We will feedback your good advice to our engineer team, thank you so much!

[@user-kt7dl6zn5z]

Какие направляющие использованы ? Как их название ?

[@josipsarkanj9065]

Also may be good to hava a detachable screen for them the big

[@Tronxy3DPrinter]

Your this advise was so good, so thanks for you. We have feedback to our engineer team.

[@Aashka_The_Mystic]

I got it set up but the bed stops halfway up and makes a buzzing noise

[@Aashka_The_Mystic]

So after much headache I got it working. I may have to drill new holes at some point in one of the bars because the z rod is not totally in straight when everything is screwed in tightly, causing it to stop

[@jonnofowler5752]

@@Aashka_The_Mystic Where do you have to drill new holes? At the top bearing?. I have a similar issue on the right hand side. It gets halfway up and jams.

[@zemiguel4216]

@@jonnofowler5752im having the same problem, any tips?

[@Mr_Pewpy_But-Whole]

TronXY how do i adjust the rollers for the z axis ? some of them move free and smooth. others are too tight andare not as smooth to move

[@Traqr]

Did you get this solved? Each carriage is supposed to be matched to its rail at the factory, but they can make mistakes - see kzbin.info/www/bejne/fYTQeKWIhZaJnKM about two minutes in for details on the eccentric bearings. Expect it to be a fiddly adjustment since there's nearly zero leeway with steel bearing wheels; make sure you matched the rails and carriages properly before adjusting anything.

[@josipsarkanj9065]

And you schouk add syncr belt for a Z axis

[@jasonsaffle13]

No need to from what it looks like it the video the machine uses 2 z motors to do a tilt adjust. Look at 18:20

[@josipsarkanj9065]

Should...sorry