Troubleshooting Issues with the Starter Circuit | Rucksters GY6 Harness

[@ORIGINALCONCEPTGARAGE]

We have the same tool chair lol

[@Smallbore2wheels]

It's a good one. Has helped a lot

[@ORIGINALCONCEPTGARAGE]

@@Smallbore2wheels right I love mine bro like it's the most handy tool box / Chair Saves You From Constantly Running Back To The Big Tool Box and Saves My Back lol

[@Smallbore2wheels]

And if you got all the tools you'll need at that time, you won't have to get up at all 🤙🏼

[@ORIGINALCONCEPTGARAGE]

I've seen this video when it first came out but I wish I would've commented but I'm doing so now which one of our bikes is doing the same thing, the button is acting up!

[@LukeKwan78]

I have a stock ruckus, and I have no power at all. Battery has been changed and verified to be at 12.8v. I’ve changed main and blue relays and checked and replaced all fuses. Stil no power. I checked grounds with my meter. Not sure what to do next

[@LukeKwan78]

Are you in houston? I’m in sugarland

[@Smallbore2wheels]

Have you measured the voltage on the battery after you turn on the key? Although the battery could show 12.8V it may not have enough juice to actually do much. Have you tried a different battery? Is the ruckus fully stock, or does it have aftermarket lights? Was it working before, if so other than having it sit, was there anything that changed?

[@Smallbore2wheels]

Yes I'm the Katy area

[@LukeKwan78]

Ill recheck the voltage with key on and off. It is fully stock. I bought used and it was not running.

[@Smallbore2wheels]

@@LukeKwan78 sometimes is an easy fix, others it could be a lot of thinkering. Did the previous owner say how long it had sat for? You may have to check and make sure the ECU and all the plugs are actually plugged in.

[@jex8046]

so what was it at the end of the day? ?

[@Smallbore2wheels]

The blue relay....but there are other issues in the harness too. The bike works just bit reliably at the moment

[@hectorbernal856]

Where is the blue relay i cant find it

[@Smallbore2wheels]

On a stock harness it's by the positive battery terminal of the battery by all the fuses. Do you have a stock harness? Mine is a gy6 one based off the stock one.

[@hectorbernal856]

I have a Gy6 harnest or i think 《Gy6 engine》 But i have noticed that i also have no power on the break ligths at all I change the started solenoid already Because when i put the key and try to trun the engine all i hear was click. I jump the started like the video shows the angine trunds over but wont start. I am about to clean the carburetor.

[@Smallbore2wheels]

@@hectorbernal856 clean the carb, make sure you are actually getting fuel to the bowl, an if that is still not working try to hook up a voltimeter to the battery terminals, you may just have a bad battery. if it dips lower than 10.5V or so you dont have enough juice.

[@MrPacattac]

It's just the starter relay went bad or has a loose connection. It's not sketchy to bypass it just as long as you are paying attention.

[@Smallbore2wheels]

Yeah that's what my money is on. I'm getting a new one to swap in.

[@GETlife]

Did you try swapping the blue relays? Maybe I asked you this already. 🤓

[@Smallbore2wheels]

😉🤫

[@littlejoey4756]

That’ll work...but once u turn it off how r u gonna restart it? Ur not gonna bring ur car with you

[@Smallbore2wheels]

I bought a hand held jumper. You might see it in one of Ceasar's videos, depending on how he edits his footage for next week *hint-hint* 😉

[@ORIGINALCONCEPTGARAGE]

I'm watching each one of your videos again lol but here is the video to the gear in our GET MOTOR Which I'm About To Rebuild For Our Metropolitan Were going to use it for my daughter's bike kzbin.info/www/bejne/b2LTonV-rbCrn9E