Tsunami 6000 spin fishing reel how to take apart and service a broken reel

[@tblindsey]

That was fun to watch, I feel like i'm part of a mentorship. I have learned so much from watching your channel. Thank you!

[@2ndChanceTackle]

Thanks for the note and the kind feedback. I appreciate it. Please stay watching - Dennis

[@Floridamarty]

I always learn something watching your videos. Thank you for your time and effort and especially sharing your knowledge.

[@2ndChanceTackle]

My pleasure! Thanks for the kind words and for watching - Dennis

[@knuckle_dragger]

I had the same issue with a D.A.M. 330 reel, freed it up & it works like new!

[@2ndChanceTackle]

Bent axle shafts are a fairly common problem, but this one went beyond normal usage. Something hit it or it hit something. This was not caused by normal usage . Glad to hear you were able to get it the DAM working again - Dennis

[@christopherjenkins2373]

Sort of an old style reel in a newer style case isn’t it. I don’t really like this kind of anti-reverse mechanism involving grabbing the rotor. I think I only have two reels with an AR that works this way. Most of my vintage reels don’t operate with an AR like this. Great video Dennis, Bent axle shafts are difficult to repair and often the only way to fix them is to replace them. With some of my older reels this just isn’t an option. You did a great job on this one. I was very pleased to finally get another reel in that Shakespeare 2700 series of spinning reels. I’ve got all the larger ones. Now I’m trying to get the smaller ones. I just need two more to have a complete set. This 2700 series of Shakespeare were made by Ohmori and were among the last ones they made for Shakespeare in 1979. They are almost as good as the Daiwa Silvers. - Chris

[@2ndChanceTackle]

Yes - it is an older design typically found in the lower cost reels. Most "modern" reels have gone to the A/R clutch, but this design is less expensive to produce, so you still see it in newer value reels - Good luck in your Shakespeare hunt! Dennis

[@paulrodriguez6403]

Another great video! Have you done a Abu Garcia 5500 two speed?

[@2ndChanceTackle]

Not yet! I will add this to my request list and try to do one if/when I get one in the shop - thanks for asking - Dennis

[@paulrodriguez6403]

@@2ndChanceTackle I have one you can service if you want to do it.

[@Mahigeer1]

I was wondering on open face bearings, is it better to grease or as sealed bearing use oil? The oil will leak through the open face bearing, but grease will stay put. However, grease tends to collect dirt more then oil. thanks for posting.

[@2ndChanceTackle]

You are correct. I normally only oil bearings because grease does trap dirt and that degrades the bearing over time - Dennis

[@Mahigeer1]

@@2ndChanceTackle Thank you for your reply.

[@edwardroberts2997]

Dennis, how is it that the drivers that you use seem to fit all the screens that you work with I don't have that luck please help

[@2ndChanceTackle]

I guess I am just lucky and kinda know which drivers go with which screws! I have a box full on my bench and keep them close at hand - Dennis

[@edwardroberts2997]

@@2ndChanceTackle Dennis I was hoping for the brand name of those tools you would give to me.

[@nahkrek]

Hello Dennis I’ve been enjoying your channel very much and I am proficient with fixing reels myself but I need an oscillation gear for a Daiwa regal Z3500T and I can’t seem to locate the part. I was wondering if you had any ideas?If you can find a time thank you very much. Glenn K. Diawa part # F24-6601

[@2ndChanceTackle]

I think that may be difficult - try contacting Daiwa directly. Their service and parts contact info is CONTACT INFO 11137 Warland Drive Cypress, CA 90630 Email: [e-mail] Telephone: [phone] & Fax Number: [phone]

[@cjmoundalexis2567]

Hi Dennis, Hmmmm ? Could it be the reel was thrown under the tires at the boat ramp to stop the boat trailer from going in the water ?!?! Yeah, that's it, dry desert humour !!! Cheers, Cons

[@2ndChanceTackle]

Yup - that was probably it. Be well and stay cool - Dennis

[@alkoch6895]

Ever find out what happened to that reel, I'm guessing slammed in a car door or rear deck lid or hatch ???

[@2ndChanceTackle]

I did not and the owner would not say! All good now - Thanks for the follow up - Dennis

[@julian9579]

hi greetings from Austria 😁 i wanted to ask if you sell reel parts 😄 im working on a penn 420ss and doing some upgrades to it like complete cleaning, bail upgrade complete bail assebly from the 420ssg for the newer line roller with bearings, new main bearing, new handle from a shimano rarenium ci4 and a new 3 washer carbotex drag system to make it a little monster ultralight spinning tank with a pretty good line capacity that can handle bigger fish 😁 and i would love to have some spare parts for it just in case 😄 i wanted to order from mysticparts but sadly they dont do international shipping at the moment 🙄