Turning Your Raspberry Pi Pico to Mitsubishi FX1N PLC

[@boxcarhobo8315]

found this one year later, got it up and going in 5 minutes, thanks for making the video

[@OnosTech]

Glad it helped!

[@boxcarhobo8315]

I finished what I wanted to build with this. I didn't use the optocoupler isolation board due to size constraints, and had flickering inputs. To get around this, each input pin that I used had a 750k ohm resistor to ground to get it to work. Once again, thanks for the explanation @@OnosTech

[@OnosTech]

@boxcarhobo8315 My pleasure

[@NeilPho]

Thank you for coming straight to the point, and telling me all that I needed to know. A perfect video.

[@OnosTech]

I am glad it is helpful

[@stefanolivingketo1076]

amazing Video and I've watched others and i'm very impressed with your content newly subscribed keep up the good work.

[@OnosTech]

Many thanks, will do!

[@rayz5508]

In your connection diagram V1 must also be connected to V2 on the opto isolator board for the circuit to function.

[@lok1614]

Fantastic! Learned PLC programming in 1985 on one of the first Melsec devices :-)

[@OnosTech]

Wooooow! 😲😲😲 Awesome!

[@donnyblackston1676]

Very cool, thanks for the video, been using FX3U and I like GXworks2

[@OnosTech]

Many thanks

[@donnyblackston1676]

Do you know if RPI Pico setup with this FW has all the instruction sets of FX1N typical Mitsibishi clone PLC??

[@qzorn4440]

Very interesting RPI PICO PLC. Next to use the WiFi and Bluetooth options. 😎 Thank you and best regards. I wish the Orange Pi5 had these great GPIO PWM examples. 🥳

[@josemartinzamorafernandez5264]

Wow thats great, thank you very much for share, keep doing a nice job with your channel (We are learning so much). Best Regards!!!! :)

[@OnosTech]

Thanks 😊😊😊

[@JoseOrtega-oz2zx]

It would be interesting to port this firmware to the rp2040 zero boards since the output pins used are not available on this board

[@OnosTech]

The outputs are available on the underside of the board except for GPO16 that is used for RGB LED

[@robboyd900]

Great Video Do you know how to get the Modbus working I can get it set as a Master and write coils but cant read registers or holding registers

[@ipecherny]

Greetings from Ukraine. Very interesting project! I had a problem with the com port driver for Windows 7. I solved it using the zadig -2.8 program, selecting the USB Serial (CDC) driver

[@OnosTech]

Great information! Thanks for sharing.

[@INTERFONESEMFIO]

Congratulations!! 👏👏👏

[@OnosTech]

Thanks

[@bobby9568]

Very cool, why should one use plc in general for waht purpose?

[@OnosTech]

PLCs are basically industrial controllers that can easily be maintained (control logic & hardware) by technicians. You can get more detailed answers from Google search.

[@tofatechengineer2005]

Very good video.Many thanks for you review.

[@OnosTech]

Thank you for the firmware.

[@fekrafebra9956]

hi my friend i tested this fimware but there is a problem in comparisons command when the condition achieved the output to any (y )does not work. please make a video for this to learn

[@dungletri4937]

2:49 Can I supply 3.3V from Pi to the input pin without connecting 10K resistor to GND? I tested ok, does it affect anything?

[@OnosTech]

OK

[@Industrialtrickstips]

can i use pico with Delta Hmi.

[@OnosTech]

You can with Modbus

[@Industrialtrickstips]

I use a serial to rs485 converter. Conv. Tx --- rx pico Conv. Rx--- tx pico In Gx Works i use D8121 address. H4081 move to D8121. 9600 8 None 1 In modbus poll show time error. But i test another Outseal Porgramme it response ok.

[@Jay_savaliya]

modbus program video please

[@alo1236546]

superb sir !

[@OnosTech]

Thanks a ton

[@allentighe9947]

Awesome 👍

[@OnosTech]

Thanks

[@roelgritter]

Great tutorial, next display with menu structure?

[@OnosTech]

Thanks! Display with PLCs like this is mainly possible with Modbus HMI. You can modify these FLProg ones for Outseal PLC to work with the Raspberry Pi Pico PLC. kzbin.info/www/bejne/nWGyooKfl55_l8k kzbin.info/www/bejne/sJLde6x7jZpsb7s kzbin.info/www/bejne/j56yhKmMbqd7nLM or use the OP320 HMI kzbin.info/www/bejne/n3SVp4ynec9oatU

[@Jay_savaliya]

Can use RS485 directly? 2:01

[@muhammadmursaleen7879]

Thanks Ur greate work.

[@OnosTech]

You are welcome

[@lenslens7379]

Please make an example with analog i/o

[@rdchannel3307]

sir ... How to download GX works 2, I Want to try

[@OnosTech]

See the link in the description.

[@dhaneshd2418]

How can i use analoge pins , how can i use d1000 and d1001

[@OnosTech]

See this video: kzbin.info/www/bejne/mojPe4ytjpmJaq8

[@bdzoom7122]

Nice

[@OnosTech]

Thanks

[@lenslens7379]

This awesome guy surprise me every week ❤ Can i use pico W wireless version?

[@OnosTech]

I am glad you like it. Pico W should also work.

[@dungletri4937]

How to convert Arduino nano to PLC mitsubitsi ?

[@OnosTech]

🙂🙂🙂