Tutorials: How to change the range and unit for volume flow for KROHNE flowmeter.

[@StartUpEntrepreneurPh]

Very informative video. Such an intellectual creature. From your real friend

[@hachebarra]

The tutorial is very illustrative. Thank you so much!

[@teamobiasvlogs495]

Wow! Thanks! I hope my video was able to help somehow.

[@zakirhussain-wi3vu]

Very good explanation

[@cyruskurtmaurillo4748]

Thank you for this video it is very helpful.

[@cyruskurtmaurillo4748]

Sir I changed the unit from kg to liter but the value is too low. Which parameter should I go to change the type of process like fuel oil diesel.

[@robhunter6772]

I'm guessing as you change the range then the current output changes ??

[@mintsanesta]

hi obias, i would like to use khone optiflux 6050 to control a tank filling of 2700L or 3400L depending on the process on the same tank, thank you very much for your videos i ve learned a lot

[@thulanigregory9382]

I have a problem, there are two kronhe mag flows in my plant, the totalizer value increases without having flow....?why..?

[@hassanhussien5600]

I have a problem with a device, that it does not read until the opening rate of the control valve is 25%? What is the solution?

[@olivertria3602]

sir! krohne 2300c display 1 error " over range" always shown.while in display 2 is correct reading in Analog input 1. it is foundation fieldbus. can y u help me sir.. thank you for sharing your vedio

[@moklism6378]

Thanks for the video, it was very helpful. Can the steam meter be set to display total kg of steam passing through the meter rather than kg/h? I have the meter set to pulse for 1 kg of steam and require the display to match the pulse output.

[@teamobiasvlogs495]

Hi! You have the Optisonic unit? Correct?

[@moklism6378]

@@teamobiasvlogs495 Hello and thanks for relying! It's a Optiswirl 4200. I may have found what I'm looking for in the manual. I think I need to change the display measurement from 'Mass flow' to 'Mass'. Setup>Display>Meas. Page>C5.3.2 Measurement 1 Line>Mass.

[@teamobiasvlogs495]

@@moklism6378 no problem. just hit me up here if you have questions. please do subscribe :p

[@muhammadimran1266]

Sir can you share me vedio link for loop test and calibration of krohne optiflex 2200c level transmitter

[@bw26brw86]

Thank you for English 🎉🎉

[@MuhammadAslam-ig3my]

Wonderful

[@hiwaali]

How to return the counter in flow meter korhone

[@soheibtaibi8976]

we need a calibration video please

[@AbdullahEstano]

Assalamuwalaikom sir us ko lang po pwedi ilagay sa online flow meter but showing no data

[@anandyadav4603]

Thanks

[@pinalmaturkar3219]

Can we set kg/hr unit??

[@teamobiasvlogs495]

Yes its possible!

[@nemesis8010]

I need information of Ifc 300, in spanish please

[@bintucbabu7110]

Bro...Genii DP1620 not connect

[@bintucbabu7110]

Any suggestion

[@teamobiasvlogs495]

do you have the corrct dtm? for which model

[@arun4846]

👍

[@ericoduro7734]

Ours in our company is always showing installation and nothing

[@RoseroL]

it doesn't match what I see in the MI for the MFC400

[@sijukannur]

Sir please give me krohne optimass service password

[@teamobiasvlogs495]

sorry. this is not something we give... only for service engineers of krohne. ✌

[@sijukannur]

@@teamobiasvlogs495 how can I change max pulse rate?