UPDATE : Jonas from AccuRC explains the CHANGES to his OMPHobby M1 setup on Radiomaster TX16S

[@BuddyRC]

BACK IN STOCK. Get yours here - b-rc.co/tx16s Free, same day shipping (if before 2pm EST), on orders over $80 out of Columbus Ohio

[@pooluop]

thanks for making it even better Jonas

[@daveapplemotors]

Thank you very much Jonas. I really like using Sa for arming (another safety off switch) I use that on all of my helis now.

[@SteinBulgogi]

THANK YOU!

[@Fluorotec]

Many thanks for posting this and to Jonas for the work. Great to see some detailed functionality of open TX in use, yet so simple to move switches. The flight modes themselves are a clear low/med/high range. 👍 👊🏻

[@jamesliu4300]

Fantastic demo. Thanks for sharing.

[@joeynexus4525]

Great, thanks for making it even better. Can you make a video of how to swap one of the idle up modes with a normal flight mode which starts from 0 throttle? 🤗

[@wvultra]

Hey TJ! Excellent video! To reiterate, Jonas is still using the Futaba/SFHSS protocol as depicted at 11:58? Thanks again for all the updates!

[@BuddyRC]

That is 100% correct. This setup is SPECIFICALLY for either the SFHSS version of the M1 or using the SFHSS satellite. By going indepth with the setup my hope is people can learn what he is actually doing and they'll be able to grow to understand how to make it work with their intended setups.

[@archades54]

@@BuddyRC What needs to change for the OMP version?

[@BuddyRC]

@@archades54 I have another video specifically for the omp setup.

[@archades54]

@@BuddyRC Can I install Jonas file and adapt it for OMP? I think the curves might be different.

[@christianhartl475]

thank you so much for the video... does anyone else have the problem that the swash plate goes a little bit out of center (to the right and back) when activating self level mode?

[@joeynexus4525]

Yes. Mine doesn’t fly stable in stabilized mode. It tilts to the side. 🤔

[@diamondt88]

Thanks TJ. Where could I download Jonas’ files of TX16s for OMP M1?

[@BuddyRC]

Link is in the description

[@diamondt88]

@@BuddyRC thanks a million

[@shanejohnstone4245]

Hey thanks for the video, very informative. I couldn't however find a link to the model file, is there one available for the Radio Master TX16S running Edge TX?

[@BuddyRC]

Thanks for watching! As of right now there isn't one because the original file has been messed up. I hope this helps!

[@alanreid250]

Hi..is there a new file that incorporates these changes???

[@petesawyer9862]

Ok so I'm a late comer to the Radiomaster echo system. But, that logical switch configuration is awesome. I just converted my Zorro over to it.

[@BuddyRC]

Sounds great!

[@richardparkiii8355]

Where can we download the file? Your other video link to download does not work. Thank you!

[@Johnny31297]

It has come to my attention that the link in the description has expired. Find my setup files here: drive.google.com/drive/folders/1B_sApz1zRyu-SaYLRz26MErWVCfFCNiL?usp=sharing

[@TheSnow520lee]

Hi, can you please share the companion file? thanks!!

[@sunson4191]

But I am using a Spektrum transmitter.... what should i do ?

[@rock4401]

Just wondering if Jonas is using a Mode 1 transmitter? Thinking he has Hold set on the SH temporary switch on my Mode 2 TX16s. Maybe if he is using Mode 1, SH is not a temporary switch? I mean I want the Hold to hold, not release when I let go of the switch.

[@BuddyRC]

Mode 2, he moved the switches physically on the transmitter. That's why he made it so it's easy to change the switch assignments in this file.

[@rock4401]

@@BuddyRC Oh so he hard modded his radio. Thanks for the reply! Oh and I just got one of your M1 FSHSS Heli's and am setting it up right now! My old brain is twisting with all these switches... might need an aspirin. Hehe

[@BuddyRC]

Oh dude I'm right there with you. When I did the initial setup videos I had to learn the setup. Then learn it good enough to make it seem like I know what I'm talking about. I used to have hair. 😂😂😜

[@haywardadams9789]

I followed your m1 set up and my right stick is not working is there something in the tx16s setting to fix it 🤔

[@mben7454]

I think I found a small bug in the Config-File: Curve "FM1" (low rpm) ist set to -35, but I think it should be -10 (for 45% throttle)?

[@christianhartl475]

good point .. i am barely able to take off with the FM1 curve

[@joeynexus4525]

Me too. I need to put the throttle stick into almost 75% before it will raise. 🤔

[@richardb8317]

HOW DO YOU GET "0" PITCH AT CENTER STICK? ALSO THE SERVO ARMS ARE NOT LEVEL AT CENTER STICK ...THE GEOMETRY IS ALL WRONG ON THE HELI...SO ANY SUGGESTION? Negative pitch is MUCH slower because of the servo arm position at center stick ..another issue which is hard to fix in pitch curves

[@skypilot23]

I'm using this file on the M2- have located the 2 switches to arm the motor and verified throttle signal is output on my monitor- but it won't spin up- wierd- SOLVED- needed to reverse output on throttle channel! all servos working correctly looks like I just need to steel my nerves now and FLY frsky sbus with remote rx

[@shtumpa1]

So he has removed the dead band from the curves now ?

[@izludfpv9419]

Thanks Jonas for all these info and this awesome setup. I am surprised to not see a single hint of expo on the pitch and roll. Do you advice beginner to learn to fly with a linear rate ?

[@svenherzing8164]

Thanks TJ for the great video. The link to the file doesn't work anymore. Is there a different location to download the model file? Thanks.

[@BuddyRC]

We will check it soon

[@joeynexus4525]

How do we get the helicopter to be responsive in positive pitch? I slams down but takes like forever to to raise. I almost need to be at 75% throttle before it takes off. 🤔

[@fredaw61]

I added the rescue switch onto my M2 model. I also wanted to add the stability mode switch as well, but in my out puts it is acting backwards. Is there a video for this?

[@ace-gc5xm]

Jonas file has no dual rate setting ,Is that becuse we set that up to are own liking?

[@helikrysly]

Thank you for the absolutely great stuff. I will use that with extensions as my template :-) But one question regarding the logical switch L07 (Switch SB). It sets Channel 5 to -100. I understood the rescue mode and your settings, but for what reason is that switch ? Many thanks Christian

[@cavu3604]

Thank you both for showing me the way! Hugely valuable and appreciated. A question: When using my TX16S Tx, what is the relationship between the M1/M2 model file and using it to fly the actual heli, and when flying the M2 heli within AccuRC? In other words, with my TX16S as the joystick for AccuRC, is the heli within AccuRC being controlled by the TX16S M1/M2 model file of rates and expo or is it being controlled by an internal AccuRC model file that has its own established rates and expo? My reason for asking is to know if I will or will not need to replicate the adjustments that I make to my TX16S M1/M2 model file (thank you for these!) also within the AccuRC M2 model.

[@jimmymann4624]

Say, hey guys thanks for the open tx file, but would you mind maybe going over the switch assignments in more detail. I think Im stuck on spin fix with only right rudder and not sure how to unlock the left rudder input? Also seems like im stuck in idle with no throttle?

[@nen772002]

hello is there a way to reverse a switch?And also how can i eliminate a flight mode? i came from Spektrum Dx7 and using a different switch for Fm0 will make me crash for few flights..thanks in advance

[@fredaw61]

I want to start using Jonas’s model for my M1 however my momentary switch is still SH. Is the only place I need to change switch selection in the Logical switch page, swamping SH for SF and SF for SH, or is the some place else I need to fix?

[@51im]

Thanks for the update. Could you tell me if a crossfire nano Rx can be used with the omp flight controller.

[@BuddyRC]

Set it up as sbus and sure can.

[@51im]

@@BuddyRC Thanks TJ that's great. Saves me spending out on frsky or spektrum unnecessarily.

[@BuddyRC]

Not a problem! I want to put one on my Tango but I'm too lazy to do the setup lol

[@archades54]

Just got the profile on my tx16s. I can't figure out what SA button does, he says it's a safety but what does it do? Throttle hold cuts the throttle, but I can't see what SA does. Nice profile from what I can see.

[@garymurphy5133]

would like to understand this to

[@oded_10]

Question, when I fly without a gyro, and I turn the helicopter on its back, should I press the button, or just lower the stick of the power down, to leave it in reverse flight?

[@richardparkiii8355]

Can these be programmed into the Zorro 4 in 1?

[@BuddyRC]

yes

[@garyowen3743]

Does this rescue function work with OMP protocol or any protocol

[@mrph678]

Awesome vid, love it! I've got a problem with mine though...i put the Jonas' set up on my m2 v2 but the pitch doesn't work correctly. It goes the wrong direction? i've tried reverse and everything i between but i can't get the collective to go the right direction. Any chance you may be able to help? :)

[@jdmsrt4]

Hey BUDDYRC! Great channel I definitely owe you for helping me almost get running on my TX16S & SHFSS M1. I’m wondering if you have a recommendation for a model file for the M1 for beginners or if I should start flying with Jonas file with stability mode on? The only video you haven’t made which I wish you did would be start to finish setup with M1 SHFSS for “dummies”. Overall I learned a ton from your videos and I wish I purchased my M1 from you. Now I know where to get parts from when I crash lol. Please advise on what you think is a good setup to start with either Jonas with stability or if you have a file for something more simple, thanks in advance!

[@BuddyRC]

Great hear you like the channel stay tuned for more content.

[@arod2051]

Is there a way to map the FBL settings for the OMP M1/2 to AccuRC FBL settings?

[@BuddyRC]

I did a video for AccuRC that KINDA goes over the settings that are equivalent in the Sim.

[@felixpradier3717]

Hi TJ, First let me thank you a lot for your videos, I'm starting with helicopters after a lot of RC plane and your videos are so helpfull! I bought an M2 V2, and applied all of Jonas tips (thank you to him too), I can't wait to see how it flies now ! I have a question (wich might be stupid) : how do you set the maximum angle of pitch? I tought it was with the radio, just as dual rates, but Jonas talks about running 16° (was 14° before) for max pitch angle, without changing the pitch curve (still -100/+100). Is it in the mix page? I don't think so, because I saw nothing in the file you shared about it! So is it directly set with the OMPHobby controller? Anyway thanks a lot for the help and your great videos wich help a lot abroad too ;) +1 subscriber from France !

[@jetplaneflyer]

Max pitch angle is set in the flight controller. If you then want to have less pitch in some flight modes you need to use different pitch curves with values of less than 100% to reduce the pitch.

[@felixpradier3717]

@@jetplaneflyer Great! Thank you for this answer !

[@lloydhutchinson9848]

Hi TJ, is there anything stopping us using TX16S with dsmx sat. on OMP protocol M1 to set all of this up?

[@icecold1307]

Omp protocol can't do this quite as well as the other due to fixed throttle and pitch curves I believe

[@skypilot23]

are the M1 and M2 similar enough - can I fly my M2 with this model file?

[@BuddyRC]

Yep!

[@skypilot23]

@@BuddyRC wow you are johnny on the spot thx! I'm sure the internal OMP rx settings will fly well but SO nice to have these settings in my tx reviewing the file - some of it is esoteric to me way over my head someday I will learn

[@BuddyRC]

Notification pop-ups are a good thing 😁 And I agree. It's cool that the omp one just 'works'. But having full control is worth learning.

[@MixedkidFridaysOfficial]

the download file not working

[@BuddyRC]

Update will come soon

[@brianwendel2528]

Hey all, great video. Added topic for this maybe could touch on Channel Mapping. My taranis setting is TAER with jp4in1se module with TAER version. For the life of me I can't get this to work unless I download module AETR Version and change my radios default to AETR. Then all works great. Just can't fly my other planes without switching everything back. Is anyone else having this issue?

[@randallwatts9840]

Would these changes be applicable for the M2 Explore?

[@BuddyRC]

Yes sir. They will work for it. Jonas is working on a setup specifically for the M2 so hopefully we will be able to have that one before long.

[@randallwatts9840]

@@BuddyRC Okay. I'll wait for that posting. I'm new to this heli and don't want to install something from the M1 model that may not work on the M2 Explore. I am using the Futaba/SFHSS protocol in my M2. I am very interested in the stabilization mode to help facilitate in my training and learning curve to help mitigate a potential crash.

[@BuddyRC]

@@randallwatts9840 oh no so it will DEFINITELY work and work fine. It's just not specifically made for the m2. The one he creates for the m2 will be his exact settings tailored for that.

[@randallwatts9840]

@@BuddyRC Thanks

[@skypilot23]

thx so much for this question! I had same and find it answered!

[@jakelang4387]

I'm about to murder my jumper tlite ! Can't figure out how to set up my throttle holds and helis on it. It's my first time setting up a heli on one..I know how to sett up a drone on one..but never a heli

[@emildimitrijevic9905]

Hi, could you add PayPal accounts for both of you? We can donate some amount to you 2. Great video and great help. Thank you!

[@DjScreaM514]

your links above have been hijacked

[@BuddyRC]

Thank you for the heads up took care of it.

[@charlieandrews976]

@@BuddyRC The link is still not working - where can I get this file? Thanks in advance.