Upgrade the steering on your Traxxas vehicle - How-To

[@RCJOE]

nice how to video guys! this looks like an easy needed upgrade 👌

[@InfiniteLoop]

Great instructional, but do you know if any replacement bell cranks exist in Aluminum for the Nitro Rustler?

[@morganhay859]

I watch these videos at least 3 times each even though I know all this stuff. You guys are very interesting.

[@Rcstreetshop]

Thank you we try to be both interesting and entertaining 👍

[@DoubleTripleOGfromtheset]

I'd like to add, showing the finished product before installing that way when we follow along we make sure it's done correctly, or as you've shown.

[@mikeshobbiesandrandomstuff]

this upgrade tightens up the front end a lot. it is a great one to have.

[@iansayer1237]

Love the videos just bought a rustler n broke it twice lol upgrade to rpm castor's n broke transmission houseing so so upgrade to rpm houseing with the steel plate nice looking n much stronger !!!

[@Rcstreetshop]

Thank you and ride/fly safe!😎😎😎

[@muddfoot69]

What’s the shock upgrade you alluded too at the end?

[@gregenglehart6795]

Trying too figure out my 1/10 Slash 2WD’s problem,after a LCG upgrade and all new aluminum upgrade on my bellcranks,steering blocks,shocks etc I’m having problems with my alignment,on my controller when I try too adjust the alignment it on goes one direction,not sure if I put the wire in the correct slot or if it is a bigger problem?

[@Rcstreetshop]

It is hard to troubleshoot over the internet (too many variables). If you are local, stop by the shop our tech will take a look...regardless steering should go in ch#1

[@Valdemar-Perez-III]

When i got my rustler xl5 for Christmas 🎄 it was slow as hell but a 2s lipo kinda did the trick

[@Rcstreetshop]

You may also play with your gear ratio a bit and make it either accelerate faster or have a faster top speed.

[@Valdemar-Perez-III]

RC Street Shop oh yeah I at first had 16/90 gearing and then I had replaced my gear with an 86t gear

[@524enaud]

What kind of horn are you using? I can't find razors edge nothing... the 25 tooth is too long to fit and the plastic horn is trash. I have a rustler that will not drive straight.

[@Rcstreetshop]

Try Protek, but it depends on the servo and the setup. We changed to aftermarket servo and this is why we put a metal arm on it.

[@jameswester650]

I like the upgrade you performed. But, the camera work hide a lot of the work you did.

[@Kenny_Edmonton]

Good upgrade video but a final shot of the finished install would of been good. I have a new servo with metal gears almost the same servo horn and Traxxas aluminum bellcrank, but I don’t know to install the horn so it fits in the rustler

[@Rcstreetshop]

Thank you for the comment, we'll definitely do.👍

[@chrisboger2750]

You mention that the first upgrade for a 2WD Traxxas would be shocks, any recommendations?

[@Rcstreetshop]

Proline!

[@bstims2506]

After changing my bellcrnk it’s binding up. Should. I just loosen those screws

[@superjoint57]

Thanks guys! I’m new to RC and learn a lot from your vids! I see a great deal of positive thoughts on this Savox servo...but I’ve seen comments about needing a glitch buster. Your thoughts on that? Thank you! 🤘🏻

[@Rcstreetshop]

Savor servos are extremely powerful and drain a lot of power....having a glitch buster helps a lot during instant voltage drops aka instant loads during steering.

[@superjoint57]

RC Street Shop Thank you very much!!! 🤘🏻

[@Rcstreetshop]

Anytime, god luck with it!

[@PittsburghFan4Life13]

I'm new to this sport, it's already addictive.. lol.. i just replaced my steering bellcrank with the one like you put on, an now out of alignment.. when turned on, it's turning to the left a lil.. how can i fix this??

[@Rcstreetshop]

Upgrades are usually not a direct replacement for your OEM parts, so sometimes you'll need to adjust it afterward. Try to change your trim settings first, before you do bellcranks

[@rattlehead7281]

Check your servo. Take off the servo horn and turn the truck on and put the trim to center. Then put your servo horn back on.

[@darjohnsom9368]

what are the part numbers for those wheels and tires I know its a late response but those are real cool

[@antreaschristou7804]

Guys is it worth it to make that upgrade for my rustler 4x4 vxl? May have some problems generally with servo or anything else?

[@dfwnick5309]

Keep up the great videos guys,..every one a gem..

[@Rcstreetshop]

Thank you Nick

[@devinniemczyk940]

I see you have strc aluminum shock towers . Do those perform well? I heard that people have issues with the screws falling out. Could you kinda help me out because I'm deciding weather or not on getting them. By the way I have a traxxas slash 2wd.

[@Rcstreetshop]

STRC make these towers out of really good alloy....and its does its job really good. Just like any other aftermarket part it has a little different fitting other then original Traxxas. Use loctite or any other thread locker your bolts will stay secure.

[@bludude41]

The rear shock tower on my Traxxas Stampede 2WD is STRC, and it has come loose on its mounts twice now. I'm gonna put some blue locktite on the threads when i get around to re-tightening em if that doesnt work i might get a plastic RPM shock tower

[@jamiewellman6986]

And for bigfoot I put vxl brushless system on it too

[@joelrangel2092]

Breathing hard there buddy!!

[@Rcstreetshop]

Work hard, play hard, breath hard...!

[@jnunez626]

What upgraded servo do you recommend for a 2wd monster slash ?

[@bloodstorm1231]

Where can i get some of those upgraded shocks and shock towers!?

[@Rcstreetshop]

Give us a call 562-425-9000 we'll send them your way!

[@Valdemar-Perez-III]

Hey do you have any heating issues with that motor on 4s? What shocks are those and could that esc take sensored motors???

[@Rcstreetshop]

1) Anything over 3S will get pretty hot, so you should consider investing in additional fan, heatsink etc 2) Shock are Pro-Line 3) With Brushless ESC you can't use brushed motors its either brushless or brushed.

[@Valdemar-Perez-III]

RC Street Shop with that 4s in the video how long do you run the car before bringing it back to cool off???

[@gcode94]

Awesome install! I'm building a Rustler from a bare chassis and looking for cool tools. Could you please share some info on the stubby screwdiverdriver you're using. I've searched high and low and have only came across a Klein stubby that's similar in size but still not as compact as the blue one you're using in this video. Keep the vids rolling out!

[@Rcstreetshop]

Thanks for your comment! That was Dynamite tool set (they have both metric and standard), give us a call, we'll get you one!

[@gcode94]

RC Street Shop I've seen the Dynamite tool set all over the internet and my local hobby shop has them as well. None of them have that blue stub handle you're using. Thanks!

[@Rcstreetshop]

Give us a call, ask Roger :) and we will get you one!

[@wurican1]

So I'm popping servo savers left and right. Bought the Vxl rustler on March 8th and I'm on my 4th saver. Will the savox upgrade stop this? Or am I just going to start replacing my entire servo? I like to run it fast and do quick turns, doughnuts, then speed off again. What do you think?

[@gcode94]

daniel walker Uuuuumm Daniel if you're asking me about your servo saver, I have no idea what you should do being that I've never driven your truck nor do I own a Savox servo. I asked about a particular tool so I have the slightest idea why you would reply to my comment asking about your servo or servo saver.

[@Gio98art]

Dude. My bandit's transmission case is breaking appart. The wing is completely busted and the body has to be held on with zip-ties.Am I doing it right?

[@Rcstreetshop]

Sounds like you are having fun! Yes, you are doing it right. But you may want to replace some of those broken parts now. :)

[@BUILTLIGHTWOUNDTIGHT]

After I'm done testing the Velineon vxl system, I will upgrade the bell cranks.

[@Rcstreetshop]

Don't forget to set your suspension to help with grip /acceleration / traction / control, especially on higher speeds.

[@nickdemyan1404]

also what is the fastest traxxas slash 2wd you have ever herd of

[@graeson8769]

Is the Futaba servo arm compatable with the Traxxas rustler 2wd servo (2075)?

[@Rcstreetshop]

Yes, they both 25T

[@joelmagana4986]

What size servo horn do I need on my 2wd Slash to replace the servo saver?

[@Rcstreetshop]

You need different servo (full metal gears and high torque) if you want to take servo safer off. Otherwise you constantly going to strip gears on the stock servo.

[@joelmagana4986]

@@Rcstreetshop ok I'm planning on replacing to a full metal gear servo but also I'm running 2.8" tires I did the monster Slash build what kind of servo do you recommend the stock one seems to struggle with the bigger tires

[@coopercliburn6698]

What servo saver is it

[@Kenny_Edmonton]

What I’m wondering is if the servo horn had to be modified?

[@Rcstreetshop]

Traxxas servos use special spacer between servo itself and a horn. Aftermarket servos do not need spacers (if you use both aftermarket servo and horn), however if you use traxxas servo horn then you would need traxxas spacer. Horns and Servos may have different tooth count. Make sure they match and everything should be good.

[@trevermiller5807]

How did you get the horn to fit in the little area? I upgraded to a mtql geared digital servo and the horn that came with the servo is way too big to replace the servo saver? Any ideas?

[@trevermiller5807]

Metal geared#

[@trevermiller5807]

It appears you have more room than me even though i have the same car. Did an older model maybe have less room? I have a 2wd rustler that came with the 2055 servo originally.

[@TndPnyRCofficial]

11:37 Hobby People reference. LOL

[@ecleland1598]

Thanks guys

[@Rcstreetshop]

Thanks a bunch for your comment!

[@tonytighttucker]

I have a question I have a rustler with the SCT Castle Creations Sidewinder motor and ESC combination 3800 KV motor what size pinion gear should I use and I want to change the slipper clutch on this car what product you suggest I change it with and do you have a part number thank you

[@Rcstreetshop]

It actually depends on your battery plus a lot of small things like what tires do yo use, where do you play (dirt, clay, pavement etc), what is your esc/motor temperature? We usually suggest to run recommended (check manual) gear mesh, before trying something super tall etc. Plus, what would you like to do with it (speed runs, bashing or something else)?

[@tonytighttucker]

RC Street Shop just bashing

[@Rcstreetshop]

To be a bit more specific, I need to know a bit more about your setup. In general, if you do not constantly break anything and your ESC/motor are no scorching hot, then I would recommend to keep your existing setup. If you want to make it a bit more enthusiastic then gear it up a bit ( 2 teeth up should be fine...)

[@jamiewellman6986]

How do I find these parts for my trexxas rustler vxl 2 wd on your website

[@skipdrummer8277]

How can I get those wheel and tires,I love them!

[@Rcstreetshop]

Easy, give us a call 562-425-9000 (10am-7pm and 9am-2pm on Sunday PST)😎

[@ravenskaugrud8410]

That thing looks mint compaired to mine lol

[@congresstart5616]

I have a rustler and it turns more to the left than the right how do I fix this its so annoying can't drive straight

[@Rcstreetshop]

You need to adjust your end points via the transmitter

[@austingupton8829]

U guys rock!

[@Rcstreetshop]

Thank you Austin.

[@byari7691]

Thank You!

[@williamgleaves1954]

What is the Savox servo that you're using? What is the model of the new servo horn?

[@Rcstreetshop]

The Servo is a 1258TG. You can use any servo horn that fits a Futaba splined servo. Ours is a Racers Edge servo horn.

[@alexandrerodrigue5085]

Nice rustler

[@chriswade3986]

What size servo horn ?

[@Rcstreetshop]

I believe 25T

[@willorc3371]

Why don't you stick the four-wheel drive slash steering in it

[@Rcstreetshop]

It is not an easy mod.

[@willorc3371]

@@Rcstreetshop what is a easy mod it's a hobby

[@markoftheus]

I have put Slash 4x4 bellcranks in my 2WD Rustler and they do work pretty good, especially for the price. The only downside is that you have to pull the whole front end off and do some dremel work in order for the bellcranks to clear the chassis. Bit tedious, but it does pay off!

[@mattsilvestri312]

Darth Vader over there lol

[@sergeant-d8714]

how bout some part numbers for the servo and the link?

[@Rcstreetshop]

The servo is a 1258TG Savox, and the Servo horn is a Futaba Splined Metal unit by Racers Edge. The Part Number is RCE10370BK

[@sergeant-d8714]

RC Street Shop thanks guys, awsome!

[@VolutedJoker]

Great video, good info. New subscriber here.

[@nickdemyan1404]

where are you guys located

[@Rcstreetshop]

We give out that info right here in the video. kzbin.info/www/bejne/oZXKqZeZoMiImsUm51s 5521 East Spring Street, Long Beach, California 90808

[@raulcampillo114]

i can do more widht fiesta rally traxxas

[@Rcstreetshop]

Everything traxxas is highly upgradable.

[@jerry3u]

Video are informative but ur big mitts block almost everything ur doin

[@DarioSpeed.]

WAIT U GUYS ARE IN LONG BEACH OMG!!!!!!!!!!!!!!!!!!!!!

[@AerialApollo]

Not trying to be mean or fat shaming but the breathing during the video is killer.. recommend playing soft music in the background while he’s assembling parts. It’s driving people crazy. Great videos, but with the breathing it’s so hard to watch...

[@JohnGomez-c7i]

Dang bro can’t breath and his not even moving

[@nickdemyan1404]

oh ok u are far from me t

[@RadiCalRaCer]

Damn that dude is breeding loudly. Is standing still that exausting? He even has food stains on his shirt...

[@obezzyjohnson9680]

Damn dude why u breathing all hard n loud like dat u only standing there put in bearing n a servo. Damn I'll hate to see how u breathe if u was workn on a real car

[@michaeljohnson254]

dudes gonna have a heartn attack jesus man do something get out use those rcs.... man