thanks for filming with tight camera coverage on what you're doing! Much appreciated!!
@UPSHIFT_ONLINE Жыл бұрын
You are welcome. Thank you for watching
@Dznuts22 жыл бұрын
Good information. Exactly what I was looking for.
@UPSHIFT_ONLINE2 жыл бұрын
Glad it was helpful!
@godinminaar90243 жыл бұрын
Thank you, my new Duke had me standing on the rear brake to keep from rolling. I think this will help.
@UPSHIFT_ONLINE3 жыл бұрын
Glad it helped. Thank you for watching and have fun with your new bike.
@Deneteus Жыл бұрын
This was all I needed to know!
@UPSHIFT_ONLINE Жыл бұрын
Glad it was useful.
@nour4lina Жыл бұрын
This was AMAZING!!!!!
@UPSHIFT_ONLINE Жыл бұрын
Glad it was helpful.
@ynoyjorge Жыл бұрын
Great video
@UPSHIFT_ONLINE Жыл бұрын
Glad you enjoyed it
@CptSlow892 жыл бұрын
Also it can affect your braking performance. I did to my vfr750 and get much better and faster rear brake performance.
@UPSHIFT_ONLINE2 жыл бұрын
Good point.
@DanielDepasquale2 ай бұрын
Thx for helping
@mope7647 Жыл бұрын
Thank you for your video. Regard Modesto
@UPSHIFT_ONLINE Жыл бұрын
Thank you for watching!
@jadenwong2713 күн бұрын
I have been having a problem where after riding for a little bit my brakes will lock up. I have bled them multiple times. Any idea what’s wrong?
@sendly_69803 жыл бұрын
helped me! you got your sub
@UPSHIFT_ONLINE3 жыл бұрын
Outstanding! Thank you for watching.
@ukdc-acdctribute11425 жыл бұрын
Hi, today I ground to a halt due to rear break overheating and locking onto the disk. At a junction leading up to this I noticed the rear break pedal felt like there was no free play I.e. as though it was already pressed in a little. I allowed it to cool which freed it up and limped home using only the front break. I changed the pads about 3 weeks ago, fluid level is not too high which I know can cause this. Could adjusting the pedal resolve this issue or should I be looking first at the master cylinder or perhaps replacing the piston seals in the caliper.
@adamhendrix79695 жыл бұрын
Literally the exact same thing is happening to me
@ukdc-acdctribute11425 жыл бұрын
@@adamhendrix7969 have you managed to figure it out? The master cylinder seems to be working fine. I've had it out since, used the rear break excessively and it's been ok so far this is actually my girlfriend's bike, it's one thing happening to me but I don't want it happening to her as she's a brand new rider.
@mytube42254 жыл бұрын
Snap same happened to me after I adjusted the rear brake leaving some free play, it then started dragging and overheated :(
@samurai45248 ай бұрын
Check if the adjument bolt is tight
@ogasi1798 Жыл бұрын
so easy 🙂 thankyou
@UPSHIFT_ONLINE Жыл бұрын
Glad you found this helpful.
@Jack-ns5zc5 жыл бұрын
Will just adjusting the pedal height affect the engagement point of the brake?
@UPSHIFT_ONLINE5 жыл бұрын
It only affects the angle at which your toe touches the pedal... not the function of the brake or how it engages.
@Jack-ns5zc5 жыл бұрын
UPSHIFT ONLINE thanks
@neildickson48974 жыл бұрын
ive a second hand 250 sxf and the pedal is rubbing on the casing is there a way it can move away or was it maybe bent in a fall
@ethanwebb64024 жыл бұрын
Bent then have to buy a new one
@UPSHIFT_ONLINE4 жыл бұрын
You could try to bend it back out and away from the case. It will likely break or weaken it to the point that it will break when you least need it to. Recommend buying a new one and keeping the old one as a spare.
@mmaaddict783 жыл бұрын
My pedal was the same way, touching the clutch cover. removed the pedal tip and used a torch to heat the back side of where the pedal curves around the clutch cover. Then I slid a piece of pipe over it and bent it out about a half of an inch. It’s been working pretty well so far.
@neildickson48973 жыл бұрын
@@mmaaddict78 bought a new bike last week.its brand new so no problems yet lol
@bog2k32 жыл бұрын
I've had the same issue on my KTM EXC. Took it out, pinched it in a vice, heated it up with a lamp and gave a few good hammer hits. Everything's good now and it doesn't look fatigued or cracked or anything, have been using it with no problem for several months already.
@quri27484 ай бұрын
thanks :)
@fallout2dxd8604 жыл бұрын
The bolt under the pedal is not turning only the nut what do i do?
@UPSHIFT_ONLINE3 жыл бұрын
The pivot bolt?
@fallout2dxd8603 жыл бұрын
@@UPSHIFT_ONLINE oh yeah, but I figured it out the previous owner had the spring broken off so that's why jt had alot of play
@thatguyrides70723 жыл бұрын
Why am i watching this? I have a yamaha 🤣
@UPSHIFT_ONLINE3 жыл бұрын
Hahaha... there are things to learn from all bikes.
@SupermotoBuild4 жыл бұрын
👍
@UPSHIFT_ONLINE4 жыл бұрын
Thank you!
@davidlong67962 ай бұрын
Im weird. I need my brake pedal higher than the adjustment will allow...
@Aydens_adventures609 Жыл бұрын
So uhh… I used this video for my… Kawasaki 140 rf and I kinda uhh locked my back wheel and can’t unlock it
@UPSHIFT_ONLINE Жыл бұрын
Well this isn't a Kawasaki 140. They are different bikes using similar but different systems. Simply revers what you did to unlock the rear brake on your bike. You have adjusted it to the point that it is locked.
@Aydens_adventures609 Жыл бұрын
@@UPSHIFT_ONLINE ok… I’m kinda embarrassed because I used a ktm video xD thx man it worked I know nothing about bikes 😂🤣