US Army Alpha Black Disassembly & Reassembly.mpg

[@LonzoPrudence]

This man out here using a whole ass drill and I’m using a allan wrench

[@TippmannSports]

@SnipingSchool That is correct. The Alpha Black has the same internals as the 98.

[@crazyncreepy50]

Thank you, can't really find good videos that shows what's inside and how to clean it.

[@TippmannSports]

@TheTito310 Lay the spring down flat inside the right receiver with the corner sticking out lying in the right upper corner. Put sight pin in. Then put the sight through the pin and line the small hole up with wire sticking up in the upper right corner. Lay the left receiver on the right receiver and tighten bolts.

[@El_Prieto]

This was very helpful. Thank you so much. I just bought one, used, and noticed the flaring O ring in the back of the bolt, and freaked.

[@TippmannSports]

@warner4455 That is true. When using an e-grip, you remove the trigger return slide.

[@TippmannSports]

@Joshysquash81 Make sure all trigger pins are installed. Try nudging the bolt handle forward a bit and then pull the trigger.

[@TylerTheT]

Theres a U shaped springy thing where the feed neck attaches where exactly does that go??? please help me asap

[@coolweed2928]

Thank you so much your video help me rebuild my whole paintball gun

[@TippmannSports]

@killajuggaloz5 They are either trigger pins or linkage arm guide pins.

[@TippmannSports]

Check out our video on the 98C Front Site Installation. The 98C has the same hopper release system.

[@TippmannSports]

@alexinsc2008 It should have 4 silver and 1 black pin.

[@TippmannSports]

THE SHORTER ONE GOES UP FRONT WITH THE TRIGGER.

[@Headphonesmusic69]

how do you put the hopper releaser back in properly

[@TippmannSports]

@UberNickel Yes

[@DerekX100]

Thank you. Very helpful

[@TippmannSports]

@xJinxedxvDTSv It doesn’t lay flat? Not sure I understand.

[@xJinxedxvDTSv]

@TippmannSports thanks got the parts i needed. its working now but i had a quik question is it ok to use vegtable oil as lube?

[@hypersergiojardon4820]

I need to remplace the orange part ,and the Orings where I can find a kit to do it please,thanks

[@warner4455]

Is it possible to operate the marker without the return trigger slide? I herd that you do not need it on eletric tippmanns.

[@xJinxedxvDTSv]

@TippmannSports i got it. I had the rear bolt upside down. fine now but im missing the triger return spring and the hopper spring is there somewhere i can buy those

[@MacMillanDAN]

Its the same with an A-5 and Project Salvo!

[@1fu11]

@TippmannSports just so you know mine only has 3 too and i had a black U kind of thing that i heard raddleing around where does that go cause i have no idea

[@gtikat]

my springs were not yellow or black but both only stainless? not sure which 1 goes where and seems like my semi fire double shoots sometimes! could this be because the springs are backwards and not catching the bolt due to lack of pressure? 1 is skinny and a little longer and the other is shorter and "fatter"?

[@lancewhite6270]

What does the little spring at the front sight look like? I think mine went "BOING"

[@Gsegura8]

Can you give the list of the tools I need to Disassembly & Reassembly my Alpha Black Tactical? Also does the TIPPMANN Double Trigger Kit work with the Alpha Black Tactica? Is it the same process for the Tactical than the same?

[@paintball8333]

i forgot to leave the feeder in, how do i put the spring back in place?

[@RifleHunter100]

Hi, i didnt leave the feed neck on (i have a cyclone) and the spring came out and i dont know where it goes

[@thegranite]

I just got a Alpha Black 2nd hand... something doesn't seem right with my sear. While I hold the trigger in, the trigger slide holds the spring "active" so it never latches the bolt back after the first shot is made. So it runs like an Automatic, but it shouldn't. Can you zoom in on the sear and show me some details that I could compare it against mine? Also the small dowel on the trigger under the slide is missing, is this critical?

[@alexinsc2008]

does the e-grip model have 4 silver receiver pins or 3 silver pins? it seems i might be missing the 2nd one(towards the back) that goes into the trigger assembly.

[@killajuggaloz5]

i took mine apart n 2 silver pins came out and i cant figure out were they go ???

[@TippmannSports]

@killajuggaloz5 Great.

[@xJinxedxvDTSv]

im having trouble with the linkage arm it dosent stay down right

[@SnipingSchool]

this gun has the same intenals as the 98 right? just a differnt style body

[@colserra383]

do you know of a website where i can buy a new sear sping because mine is bent

[@1fu11]

@TylerTheT i have the same problem you know where that goes?? please help

[@Joshysquash81]

Last time I took apart my gun I believe a part fell out, so now when I cock it, it stays cocked even when I pull the trigger, whats wrong?

[@UberNickel]

its the same as the bravo right

[@hernaldo14]

do i have to open it up to clean it each time i play paintball?

[@Godbody90]

Been having issues with my Alpha Black Elite misfire and it shoots when it wants to but mostly the time that I'm using it on fully auto tryed using it on semi-automatic and still the same problem is it possible anyone can do a video on that issue

[@killajuggaloz5]

@TippmannSports i figured out were they go...

[@thehavoccompany-a3]

THANK YOUUU!

[@FC3_Papo]

what happens if i kinda broke the little orange thing at the beginning of the gun u mentioned?

[@Moisty_Yams9000-tf7zx]

The paintballs will roll out of your gun when your marker is facing down. It's really annoyin

[@PatVegas89]

Hey guys, I have an alpha black that im having trouble getting over 160 fps. Any advice?

[@heritageandhope]

very helpful, thanks

[@bobdabuilda1388]

Hi, can anyone help me and tell me how to change out the rear bolt cocking handle and the rear bolt? I would really appreciate it, thank you in advance!

[@sicksoulmandy]

can u tell me the diameter of the buffer o`ring? tanks :D

[@stpmac]

Hi, I had the same issue :S can you please send that link?

[@xXxBlazeFirexXx]

My freaking power tube broke... Great.

[@TippmannSports]

Painting the marker while completely assembled is not recommended.

[@killaabeas]

not helpfull i need to kno how to a pice of the internals

[@TippmannSports]

@Dennen2009 Please contact our service department at 800-533-4831.

[@TippmannSports]

@xJinxedxvDTSv Please call our sales department at 800-533-4831 and they can point you in the right direction.

[@TippmannSports]

@steifenwagon Please call tech support for parts at 800-533-4831 or 260-749-6022.

[@TippmannSports]

Please send an email to [e-mail] and I can send you a video that might help. (KZbin won't let us post links). Please include your original question and KZbin account name.

[@thewistleboy]

its not even a disassembly!!!! he just takes the top off then he puts is back on! he doesn't even remove the internals!

[@TippmannSports]

@paintball8333 Call us for help at 800-533-4831 or 260-749-6022.

[@thehavoccompany-a3]

TT_TT .... i am such an idiot... i carefully took my alpha black apart and now i have anxiety..... i hope i can put it back together with my father and friend with it working fine afterwards.... I SHOULD HAVE NEVER TAKEN IT APART SO PLZ SOMEONE IF YOU CAN HELP PM ME! i know it's fine but i just feel like i might mess up... just tell me something to calm my worries TT__TT

[@TippmannSports]

Please call our tech support team and they will assist you at 800-533-4831.

[@TippmannSports]

Please send an email to [e-mail] and I can send you a video that might help. (KZbin won't let us post links). Please include your original question and KZbin account name.