2006 Rainbow E2 Gold Teardown Cleaning And Bearing Rebuild

[@mrkcaldwe5]

I just bought a used E2 Type 12 black series off eBay. It was not well maintained at all. This video was super helpful in tearing it down so I could get to the fan blades to clean them out.

[@VacLab]

@@mrkcaldwe5 fabulous!

[@brittanybarlow194]

Thank you for this video. You are correct there was no other video about bearings. My parents rainbow is not working properly so I’m going to try and service it myself. It mainly just needs a deep cleaning and bearings and maybe some new seals.

[@VacLab]

I wish you good luck.

[@brittanybarlow194]

@@VacLab well after 1 week I have finished servicing my rainbow. Thank you so much I couldn't have done it without you. The Rainbow is working like a charm.

[@VacLab]

@@brittanybarlow194 yay!

[@TRec3791]

She finally got a full tear down and cleanup. Yay...

[@keithnoneya]

Thanks bud. I have this same model and the 2nd bushing on the motor side I couldn't figure out if it was part of the shaft or just came off. I used some channel locks on it and it came off so I could clean it up. I took mine apart because of the big seal and dirt in there. Thanks for sharing. Best Wishes & Blessings. Keith Noneya

[@VacLab]

You're very welcome.

[@binkhalifa2004]

Instructive video. I liked the music too - was nodding my head to the music.

[@colterkardas4105]

This is by far my favorite Rainbow model. I don’t know why, but I love the graphics on it. Although, this model had two different types of controllers and designs. The original design of this E2 did not have the insulation and the controller was much louder and sounded a little higher pitched starting up into high speed. The early 2007 model of E2 gold, they added insulation and changed the controller into the same one that the E2 platinum has. I only know this because I used to work at a Rainbow service center. Lol :-) I own the SRX Rainbow- always have the “latest and greatest.” I have a couple videos on it on my channel. This is the first Rainbow model that I am NOT at all impressed with. First off, it was purchased in December of 2019 with an unknown recall at the time- it has since been updated and fixed by Rexair- a piece of insulation needed to be put on the controller- a couple machines apparently caught fire before they had that insulation put on... yeah, that made me quite concerned when I read about that- as I was on vacation with that same Rainbow running on low speed at the house... 😱😱 Second- it gets hot- QUICKLY! I can’t run it for more than 10 minutes on speed 3 (cleaning the air) without turning off...luckily, it does have a safety switch to turn itself off otherwise it WOULD catch fire... Third- The intake at the main unit (where the hose plugs in) is VERY small causing a restriction of air (massive restriction) when using the hose/attachments. I have compared the cleaning power at the hose end with the black Diamond and it’s not even comparable...I use my black Diamond for all the cleaning... just the SRX for air cleaning. My SRX is currently at the shop as it’s under warranty- it continually shuts off, randomly and they are thinking it’s the controller- it may need replacing. I took it once -last week and had it back for not even 24 hours, running it on low speed to clean the air- cranked it up to 3 to add water to it through the intake and then it shut off... very warm too..they “reset” it, but now it’s back in there... Now, with all this said, I DO like the power head design- they FINALLY after 85 years, have added a foot release pedal- so it HOPEFULLY will stay standing up 5+ years down the road. 🤣 -Metal roller bar with replaceable bristles (back to the Platinum design) -On the E2 Gold (2004) through the Black Diamond (2019) there is a plastic grill which allows the controller to breath and even gently pulls air in (to cool the computer)- and while I know it needs to breath, properly... it allows WAY too much dust in there, which overtime, if not cleaned, regularly can overheat the components and BAM- new controller is needed (about $350 new)... so- I quit using the black Diamond to clean the air on low speed and will just use it to vacuum and clean the air (briefly) on high... (When I cleaned Rainbows at the service center, you’d be surprised at some of the dust and debris in the controllers...worse than a 2000’s desktop computer...) I’m honestly surprised more machines didn’t catch fire 🔥 -The SRX is sealed to that controller now, at least from what I’ve seen... so that’s good, and bad... good because no debris can get in the controller, but then also it overheats BECAUSE it can’t breath...

[@cmart9240]

I am enjoying your videos so far. I also have an e2 gold series and it stopped working couple of weeks ago after I accidentally stored it with water still in the bubble. I let it sit out and air out and it starts up now, but after watching your first video about basic maintenance, I just did that today (03-30-2024) I am now on the hunt for a new water duct filter/gasket and potentially a new HEPA filter. I rinsed my filter out today but might still consider replacing it. I've owned this vacuum since brand new and this is my first time doing any kind of cleaning on it. I'm surprised maintenance can go into this much detail and hopefully I'll get another 20 years out of this vacuum. My only question is, possibly including links to where we can buy new parts from?

[@VacLab]

Google is your friend. Rainvac is great as well.

[@cmart9240]

@@VacLab Yeah I ended up finding rainvac website. But wow, didn't expect that kind of disrespectful reply from a creator.

[@tariqmidhat4345]

Woooow. I has the same sound in my Rainbow. Thank you very much 👍👍👍

[@VacLab]

I hope you can get it fixed soon.

[@abu1omar1]

Thanks a lot man for sharing, appreciate your help..

[@AxlAX]

Thank you for this break down. Now I can service and clean out the fans on my Rainbow🌈😊 perfect 👌

[@VacLab]

Your welcome!

[@dianastriker2309]

Thank you. I will try to find the circuit breaker.

[@dobecom]

My machine could not turn ON so I took it apart like how you did it. And I found a small capacitor that drop off the circuit board. I am not sure this is the causing the problem but I try to get someone to have it replaced and see what happen. Hope it will be solved. Thanks for sharing the video. It was helpful. Robest Yong Malaysia

[@therandomman6647]

Just got one for Christmas and it has a 16 second rundown

[@VacLab]

That's somewhat on the long side. 😁

[@ninosubotic04]

Hi I have rainbow e2 gold from 2004/2005. I have aquamate 2 but I found great deal on aquamate 3 (for the blue series 2009) . I’m interested if I can use it on my rainbow e2gold or is it only compatible with blue series… I’m not sure is there a difference between electronic hoses on gold and blue.

[@VacLab]

You'll need a newer hose. The older E2 gold hose won't fit.

[@dianastriker2309]

Help! Bought an e-series last week and set up the power brush and it doesn’t want to stay on. The red light comes on and when I push the reset button, I have to hold it in a certain level and it will go for a small amount of time. I have cleaned the attachment. Replaced the belt. Looked at the reset switch. No loose wires. Do you have any suggestions.

[@VacLab]

@dianastriker2309 seems like you have an open circuit caused by worn connections. Have someone service it. Or, it could be a bad circuit breaker in the PN.

[@AustinHook-x2p]

Love this rainbow

[@AustinHook-x2p]

Very helpful

[@nolanreach2088]

God you talk so slow, even at 1.5 x speed up you talk like normal people. But I deeply appreciate the video of disassembly!

[@excitationofstereocilia2103]

But that music tho 😂

[@tylonbarnes9678]

what size bearing puller you use?

[@VacLab]

The smallest, about $8 USD.

[@mtt6709]

Thanks for sharing your video. I've a couple of questions on the motor, hope you can help: 1. What is the voltage and amperage rating and RPM? 2. Is it a DC or AC motor? 3. Are there any carbon brushes?

[@almightyian]

There are no carbon brushes

[@MT-pg8lq]

Can you help me? When I turn on the rainbow vacuum, it will make 3 ticks sound and won't spin the motor. Sometimes after adjustment (opening up and etc), it will work for awhile and then stop again. I assume the controller is entering into "Automatic resetting motor protector has tripped." frequently but I cannot for the life of me figure out the reason.

[@VacLab]

You have a major electrical issue. Either have your dealer fix it or use it for parts. The dealer will want you to purchase a new one of course.

[@joshuaryanferguson3702]

soo i saw bissells proheat and proheat series but what i noticed is that the proheat advance has a heater built in because it has the two rocker switches but not on the others do they actually have a built in heater or no cause all i see is heatwave technology an not built in heater

[@therandomman6647]

Hey man! I'm wondering if you could make a video of you putting the modern gearing in a kirby, you know the spot where the motor connects to the transmission, in the gen 3 through sentria I believe there is different gearing there.

[@MT-pg8lq]

Just curious, how do you replace the "TOP BEARING"? The top bearing is a bit noisy, I hope to replace it.

[@VacLab]

That would require a video, wouldn't it?

[@MT-pg8lq]

@@VacLab yup.. Anyway I think my controller is dead... Cannot seems to find a cheap replacement anywhere.

[@VacLab]

@@MT-pg8lq Last time I priced a controller, it was around $300-$400 USD. Definitely not worth it.

[@MT-pg8lq]

@@VacLab agreed. Not sure how it died too, I greased the bearings the way you did it and maintain it quite well.

[@excitationofstereocilia2103]

@@VacLabwhat is the controller?

[@teacherlynn671]

Can you tell me how to replace the water pan neck gasket. Is it glued in or ??????

[@VacLab]

It's glued in.

[@jh4db536]

Ohhh this use brushless (electrically commutated) motor very fancy 🌈. Have tried using ultrasonic cleaner on ball bearing?

[@VacLab]

Nope, don't have one of those sitting around.

[@nolanreach2088]

3:53 how did you disconnect the FFC unit from the motor?

[@VacLab]

It just pops off. Rock back and forth while pulling upward gently.

[@nolanreach2088]

@@VacLab wasn't as easy for the first time for some reason. But I finally figured it out. All done, but I had the other issue for not fitting the rubber ring of the motor inside the plastic part, only realize that it was the issue after turning the machine on and feeling slight vibration that's why I figured something is wrong now it's back in spot no complaints, a side of the issue that I ordered the phone that doesn't fit my machine but okay

[@autumnmunro9105]

How do I get the washer out from under the first blade mine is stuck !!!!

[@VacLab]

Try WD40 and some pliers.

[@softgold9430]

Hello. please tell me - what is the price of the original air filter for the model (RAINBOW E2 Black) in the USA? Thank you

[@VacLab]

www.rainvac.com/

[@ajf2005]

Can you do a whole house cleaning with both E2’s??

[@VacLab]

Well, I don't have an electrified hose at the moment, so I can't use either one of them. But I did a whole house cleaning with Thomas' E2 Platinum Blue a few months back. Did you happen to see that video?

[@ajf2005]

VacLab Yes I did 😊.

[@ericpippen7915]

What is the difference between the E2 Gold edition and the Blue edition. I have the blue edition

[@AxlAX]

@@ericpippen7915 the color and probably foam insulation. Some gold's got it and others didn't.

[@ericpippen7915]

@@AxlAX thank you for the response!

[@MrJoseph3005]

Good day sir , can give code of bearing , for upper & lower

[@VacLab]

Top motor bearing is 6001 and lower is 6000.

[@jani-online8715]

Step 1 - Pull the plug / cable out of the power socket !!! 😉

[@VacLab]

I prefer to work with live electric. 😂😂

[@tylonbarnes9678]

can you send me the link to ebay for the motor bearings?

[@VacLab]

Links change daily. Search for 6001 and 6000 types.

[@tylonbarnes9678]

@@VacLab I pulled up vacuum cleaner motor bearings

[@diyschick5394]

Help. I can not afford an E2. I have DC4 that I inherited. I took is apart to clean the separator and the bottom side of the separator was so disgusting I removed those parts and cleaned them too. Now when I am reassembling I am running out of bolt that comes through motor that everything attaches to where I have no room to screw final nut back on. Maybe 2 rows of threads are showing but one would have to apply a lot of pressure on the plastic separator to get the top nut back on. Even if I could I believe it would crack the plastic. HELP I have watched all videos I can find the replacing parts look just like the video. I honestly don't think you could reverse them if you wanted to.

[@Ower696]

Tell me the marking of bearings in the motor

[@VacLab]

Lower (in plate) is 6001-2RS Top (armature) is 6000Z

[@Ower696]

@@VacLab Thank's why we pay great! And in rainbow e1, what are the prices?

[@VacLab]

@@Ower696 I buy everything on eBay. About $10 for a 10 pack.

[@Ower696]

@@VacLab What bearings are installed in the rainbow e1(eseries) in the motor

[@VacLab]

@@Ower696 E2 one speed uses 608z (top) and R6-2RS (lower).

[@rwdplz1]

I'd spend the extra $8 and get a good Timken bearing

[@VacLab]

So 5 years and still working just fine.

[@oandacomicsinc3138]

That doesn't have foam in it 😔

[@FrenchFryCheese04]

Mine is from 1998

[@Jardinesdelteatrord]

En español por favor

[@maeganrussell9418]

Hoping you might be able to help. I followed your video but my machine will not turn back on. I think it's because this part is in the wrong spot. Any ideas? I took a video so you can see it and see what I've tried so far. Thank you! kzbin.info/www/bejne/iZbKiGWlp9l_f8k

[@edywatson9791]

I am the only one who noticed, that poured wd40 into the water system? Let's take care of water

[@VacLab]

You do realize that impurities are filtered out at water treatment plants, right? What do you think happens to residential sewage? And, have you ever used chemicals to clean your tub, sink and toilet? Where do think they go?