Vacuum Tube Radio PCB - Vintage Circuits

  Рет қаралды 29,486

Electronoobs

Electronoobs

Күн бұрын

Пікірлер: 59
@ELECTRONOOBS
@ELECTRONOOBS 2 жыл бұрын
Arduino Course LEVEL 2 (Spanish): bit.ly/2ZNWgqy Follow me on FACEBOOK for more: facebook.com/Electronoobs Help me on Patreon: www.patreon.com/ELECTRONOOBS
@gvii
@gvii 2 жыл бұрын
I really love tube circuits. One of these days I'll get around to finishing the tube amp that I was making with magic eye tubes to show the levels on the two channels. I don't really need it, but I have very fond memories of a radio my grandparents had that used magic eye meters that I was absolutely fascinated with as a kid. There's not of devices left these days with those style of level meters that are still working or reasonably restorable, but the magic eye tubes are all over eBay fortunately.
@Ray77582
@Ray77582 2 жыл бұрын
Vintage circuits can make a very good series. Please make this series.
@Delali
@Delali 2 жыл бұрын
Seeing this video, i realise how much i miss you, your amazing videos and accent. I have been away working on my own channel. Feels good to see you my friend.
@whodatdere1
@whodatdere1 2 жыл бұрын
In this style of radio the iron core is the directional antenna, so it would make sense that you touching it will help with gain. The audio output of these circuits are typically high impedance at least 2k ohm or higher. If you were to use a crystal radio earpiece without the transformer you may have had better results. Or earbuds after the transformer would have worked as well. The 3 tube set will allow you to drive a speaker
@barrymayson2492
@barrymayson2492 2 жыл бұрын
A lot valves use transformers in the audio output which might account for low volumes. Just a thought. Great to see you try out things that take you into new areas.
@ConsultingjoeOnline
@ConsultingjoeOnline 2 жыл бұрын
Love the projects!!!
@rinokentie8653
@rinokentie8653 2 жыл бұрын
Nice project! Your anode supply voltage is very low causing distortion and low output power. These valves are typically suitable for 70 to 90V.
@AnandKumar-ym9yw
@AnandKumar-ym9yw 2 жыл бұрын
Love this project, next should be on FM transmiter 😍😍😍😍😍
@mbak7801
@mbak7801 2 жыл бұрын
You could use 3 PP3 batteries taking the supply up to 27v. Also check the load impedance of the 2P2 and the turns ratio of the transformer and see what impedance speaker you will need. Using the wrong speaker can really mess things up as well. All in all it looks an interesting start for experimentation.
@dz-abouttechnique1849
@dz-abouttechnique1849 Жыл бұрын
Nice video!
@OrwaJammoul
@OrwaJammoul 2 жыл бұрын
Wish you all the best .. hard working and very smart guy
@DIYwithBatteries
@DIYwithBatteries 2 жыл бұрын
That was cool Bro 👍 yes it's fascinating ;)
@PhG1961
@PhG1961 2 жыл бұрын
Cool project !
@CasualyCompetitiveGamer
@CasualyCompetitiveGamer Жыл бұрын
For finding the MHz you can do 1/2xπ√LxC L(inductance) C(capacitance)
@VoltageNostalgia
@VoltageNostalgia 11 ай бұрын
Great video thanks
@Dinocelisaandtonni
@Dinocelisaandtonni 2 жыл бұрын
Pcbway es carisma!
@Wtfinc
@Wtfinc 5 ай бұрын
Oh thats cute! I think i have all the parts!
@kayezero703
@kayezero703 2 жыл бұрын
i was watching your "make an arduino at home" and i have some questions
@leehewitt9559
@leehewitt9559 2 жыл бұрын
Love it !!👌👌👌
@zentheplayerrapper8504
@zentheplayerrapper8504 2 жыл бұрын
Esta bueno :v bro saludos 💪😉
@mohamedaqeelmohamedsufiyan9996
@mohamedaqeelmohamedsufiyan9996 2 жыл бұрын
Hi I like watching your every video And I have tried most of them If you can please upload video based on Induction cooker how it's circuit works And how to make a diy Induction cooker
@kumar-np8dm
@kumar-np8dm 2 жыл бұрын
Please make a walkie talkie in vhf range
@eletronicaeautomotiva
@eletronicaeautomotiva 2 жыл бұрын
Excelent project
@captmohelsaadany6751
@captmohelsaadany6751 7 ай бұрын
I have a couple of 6cb6a vacuum tubes Can i use them for this project?
@pie9967
@pie9967 2 жыл бұрын
Can you make a tutorial on how to use Nrf24L01 with Esp32 Dev kit
@VijayaLakshmi19807
@VijayaLakshmi19807 2 жыл бұрын
Sir this is really nice project. Try to improve audio quality and Also try to make a radio transmitter. Please don't forget to make a video explaining the uses of capacitors and how to use them in circuits effectively. Love from India ❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️
@wild-radio7373
@wild-radio7373 2 жыл бұрын
COOOOOOL!!♡♡♡
@hassanx146
@hassanx146 2 жыл бұрын
Nice video 👌👌 please do guitar 🎸 amplifier
@garygullikson6349
@garygullikson6349 Жыл бұрын
Description and circuit for 2-tube Man from Mars Radio Hat from 1948 en.wikipedia.org/wiki/Radio_hat
@taranagnew436
@taranagnew436 2 жыл бұрын
what do the tubes do on the radio?
@joseluisfernandezrodriguez2241
@joseluisfernandezrodriguez2241 2 жыл бұрын
Como no saturaste más la señal a las válvulas y sacar el audio con chicha y más saturación en la remodelación.., después filtrar con condensadores.... Casi ni me acuerdo cómo eran esas viejas radios am de valvulas
@parsavosough4277
@parsavosough4277 Жыл бұрын
niceeeeee❤
@Pulverrostmannen
@Pulverrostmannen 2 жыл бұрын
I think the device would work better if you ran it with more than 9 volts, since tubes are high impedance devices they will work poor with low voltage plus you get very little power out of it as well which tend to distort. too bad in my country AM radio is not available at all so it is pretty much useless here
@ELECTRONOOBS
@ELECTRONOOBS 2 жыл бұрын
I will try. I've used them at 12V but I was afraid with more than that since the schematic was marked as 9V. Thanks!
@Pulverrostmannen
@Pulverrostmannen 2 жыл бұрын
@@ELECTRONOOBS as long as your capacitors are rated for the voltage these DL92 tubes are rated for a maximum plate voltage of 90 volts. And the G2 grid should not exceed 67 volts so the tubes have a good headroom upwards. However does these tubes have a very small output with a maximum of about 270 milliwatt at absolute most so you won’t get much. However is the power increasing with the voltage. But check that your resistors are suitable for the increased voltage so that the led and other stuff won’t take damage. Otherwise you could probably safely go up to 60 volts without any issues :)
@NiHaoMike64
@NiHaoMike64 2 жыл бұрын
@@Pulverrostmannen Easy solution is to just omit the LEDs, actual (old school) audiophiles consider LEDs under tubes like putting cheap ketchup on fine sushi.
@Pulverrostmannen
@Pulverrostmannen 2 жыл бұрын
@@NiHaoMike64 ha ha I know right? I have built several tube amps and have a complete hifi system which I built myself and I didn’t use any LEDs to light my tubes. It’s better to use tubes that glows much to begin with instead ;) that we all like to watch! Nothing like 500 volts feeding tubes glowing with red hot cathodes. Omg I like that!
@mr.q3216
@mr.q3216 2 жыл бұрын
Like someone said you need an AM antenna.
@10356665
@10356665 2 жыл бұрын
my dream project please make transmitter am and fm thxxx
@topgearIQ
@topgearIQ 2 жыл бұрын
Any tube transistor
@vivetu
@vivetu 6 ай бұрын
Are you living in Spain?
@Digital_Ustaad
@Digital_Ustaad Жыл бұрын
How to convert EZ80 TO DIODE PL DIGRAM .
@GP-GetusProject
@GP-GetusProject 2 жыл бұрын
mantap, keren
@Jkauppa
@Jkauppa 2 жыл бұрын
nano-micro vacuum tubes as transistors
@Wtfinc
@Wtfinc 5 ай бұрын
When you show the schematics, can you do us all a solid and show us straight on and don’t move it for half a second so we can screen shot it. It’s just so easy to screenshot Edit: I tried using your link and that website is just the worst. Theres no actual download link, just a bunch of traps that look like download links. And for some odd reason I couldn’t save it to my photos like saying. And its not from a lack of trying. Idk
@drxfuncaption9322
@drxfuncaption9322 2 жыл бұрын
How design my own smsp circuit
@akhilgopinath6815
@akhilgopinath6815 Жыл бұрын
I need the board. Can you give me
@samamani5423
@samamani5423 2 жыл бұрын
"let's ged starteth"
@longdongsilver4719
@longdongsilver4719 2 жыл бұрын
Am I the only one who is surprised by the low 9V power supply for a tube? That's way too low. Even for a tube rated at only 60V.
@Amperekaefer
@Amperekaefer 2 жыл бұрын
👍👍.
@ChrisLocke1969
@ChrisLocke1969 2 жыл бұрын
that speaker is not so good - I've tried them in projects... try better ones
@arjanbroekhuizen9298
@arjanbroekhuizen9298 2 жыл бұрын
use a better speaker for a better result
@muthumohan9947
@muthumohan9947 2 жыл бұрын
60 volt dc 10 amp electronic load tester circuit without arduino
@itamarcohen6868
@itamarcohen6868 2 жыл бұрын
Noice
@immensiverocker4813
@immensiverocker4813 2 жыл бұрын
That speaker is not good option
@de-bodgery
@de-bodgery 2 жыл бұрын
This might have been 100% a waste of time.
@VoltageNostalgia
@VoltageNostalgia 11 ай бұрын
Why? This is great information to learn. If the Internet goes down, knowing how radios function and how to make one is invaluable.
@kevinjames6385
@kevinjames6385 2 жыл бұрын
You are telling lies want you try running your motors forward and backwards
Vacuum Tubes Pre-Amplifier PCB | How Vacuum Tubes Work?
14:44
Electronoobs
Рет қаралды 34 М.
A Vacuum Tube Single Board Computer?!
22:21
Usagi Electric
Рет қаралды 99 М.
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 42 МЛН
I thought one thing and the truth is something else 😂
00:34
عائلة ابو رعد Abo Raad family
Рет қаралды 22 МЛН
Vacuum Tubes POWER Audio Amplifier -  How it sounds?
13:16
Electronoobs
Рет қаралды 21 М.
Let’s Build a Low Voltage Vacuum Tube Audio Amplifier
19:57
Usagi Electric
Рет қаралды 137 М.
The Vacuum Tube and the Invention of Radio
10:57
Technology Connections
Рет қаралды 433 М.
Philmore Crystal Radio Kit
25:41
Michael Simpson
Рет қаралды 30 М.
Your First Tube Radio Project
19:03
MIKROWAVE1
Рет қаралды 23 М.
HOW RADIO WORKS   1943
10:28
Ron Seventy Eight
Рет қаралды 36 М.
Capacitor Experiments - How They Work?
15:28
Electronoobs
Рет қаралды 54 М.
Old tubes radio restoration: 1957 Nordmende Thannhauser 58
8:17
SomeStrangeVideos
Рет қаралды 20 М.
#355 Let's try to build a Vacuum Tube Radio
19:26
Andreas Spiess
Рет қаралды 101 М.