Valve adjustment on a Volvo D13

Thanks for watching! please like and subscribe!

[@TATEXPRESSINC]

Awesome Video!🎥

[@PlayerzAnthem]

nice video man I just hate seeing people using a 700$ torque wrench to break stuff free

[@Rudysgaragellc]

It’s not your tool so why do u care ?

[@mechmobile2019]

If it's advertised of meting capable 100% possible it could be safe for the tool

[@johnysilver1853]

Did you adjust engine brake as well what minute on the video?

[@isaaccharles4051]

Great video brother I am new to your channel already subbed learning a lot about these Volvo engines thanks for the video God bless

[@cliffordcolemon4279]

Thanks I needed lat more God blessings

[@moisesautoandtruckgarage6024]

Keep on blogging sir and sharing your knowledge. This is my support from #MoisesAutoAndTrucksGarage

[@mechmobile2019]

Good job . How to decide when to use a shim and when to adjust the nut and bolt to tighten the shimm?

[@Gumigeling00]

While this might be "ok", it is not correct way to do the overhead adjustment on Volvo engines. When you finish, engine should have made 2 revolutions. So do Intake and Injector, then turn engine and do exhaust and engine brake, then turn again to do intake-injector and so on. Also, make sure cam mark is between two lines (not close to 1st or second but between them).

[@paulstruckrepair6016]

Arnes Kadic have you ever set timing on a d13? If you have you would know the mark has to be closer to the first mark for the most accurate adjustment

[@Gumigeling00]

@@paulstruckrepair6016 have you ever done it? Did you get newes buletin on setting timing? If you did, you would know that it has to be in middle.

[@Gumigeling00]

@@paulstruckrepair6016 check Operation 2140-05-03-01 dated 08/12/19

[@paulstruckrepair6016]

Arnes Kadic buddy iv don’t this a 1,000 times your not teaching me anything I don’t know 👍

[@Gumigeling00]

@@paulstruckrepair6016 I understand, and maybe you have done it 100000 times, I am saying way you are doing it is not the way Volvo does it, or recommends doing it.

[@e7sasrayg]

Where did you get these sizes?

[@taiviet20]

you dont adjust the engine brake?

[@juanvelasco1971]

Do you help with valve adjustment?

[@berenicerobles4654]

Hello, excellent video that the adjustment sheets have administration, injector and brake in Spanish please

[@armandodomingo9468]

Hi, How about the exhaust brake?

[@rudyalvarez8339]

Where are you located I need some work done on my volvo

[@alexandertakele6136]

Hi boss, i got a question I have a 2013 Volvo with d13 820k now def deleted still has egr I replaced injectors a year ago . Ever since I replaced the injectors I get a lot of fuel smoke blueish whiteish only at first start up and if I shut it off for 20 min and turn it back on. After warmed up I can’t see the smoke but can smell it. Do you know what it could be ? I can’t get a mechanic to figure out what it is

[@emlkl1779]

Exhaust valve isn't adjusted properly .hence the smoke

[@elioavila99]

Alexander , I have the same problem with my Volvo . Blueish smoke at startup and misfiring then after 5 minutes goes away . Did you ever find the cause for this issue ? Asking for my self I want to know . One mechanic told Me is just the injector and once the injector gets warm it stops . He said I don’t need to worry about it

[@antoniobermudez4989]

Hey friend. Where can I buy the adjustments shim kit. That is not in Volvo dealer

[@paulstruckrepair6016]

Volvo sells the shims individually not as a kit

[@user-qg1xg8eu2r]

كم رقم الشفره اللي تستخدم لعيار البلوف

[@taiviet20]

Did you turn engine by alternator?

[@paulstruckrepair6016]

Tai Tran yessir

[@e7sasrayg]

You could get the same tray that's in the video

[@paulstruckrepair6016]

Volvo dealer or Mack dealer

[@samankirkuk9461]

What is the measurement in mm in and out?

[@paulstruckrepair6016]

saman kirkuk exhaust 991mm. 203mm intake

[@samankirkuk9461]

I mean Phils Rev up

[@mohammadrabbani4113]

Hello sir give valve adjustment matohd and injector adjustments i want pdf files please

[@gerardquinn2572]

Where do you get the boxes of shims ..

[@paulstruckrepair6016]

Mack dealer or Volvo dealer they don’t sell the whole box you have to buy them individually

[@arthurvilla8636]

@@paulstruckrepair6016I’m currently doing a overhaul on a Volvo d13 same engine anyways and I can’t bar the engine over by the alternator I was able to but once I kept adjusting the valves it got hard af to turn to the point where I can’t anymore.

[@coachafrane3521]

What sizes of filla gauge do you need

[@paulstruckrepair6016]

8 thousands for the intake valve ,39 thousands for the exhaust valve, and for flats for the injector, 

[@Silvervwolfee]

What does that mean "for flats for injector"

[@SalvadorBtc]

@@Silvervwolfee the nut has six flats or sides. So you turn it 4 flats...I hope I explained it well

[@quientonsmith1395]

Awesome work basically open heart surgery. If you own the truck you have to rely on the mechanic really giving a s($& because he could essentially just pop the valve cover and put it back on for the labor