Valve clearance adjustment in honda hornet 160r

Valve clearance adjustment in honda hornet 160r

[@Sharankumar.k]

Bro aap ne to inlet valve 0.08mm or exhaust valve 0.24 rakha hai exhaust jyada raha hai kya is se bhi bike smoot chalegi

[@jitheshkk8447]

Very good video. Shows the complete process....

[@john4mHyd]

Is it Valve problem in hornet bikes are common ??

[@mahdihasan5626]

In 0.06 Ex 0.24 Ap kiya setting kariye?

[@amitgupta2861]

Ap esko kitne kilometers pe kar rhe Ho...

[@sathyanputhanpurayil6799]

There is no need for removing fuel tank for valve clearance adjustment

[@Sharankumar.k]

Bhai Ek expert banda inlet valve 0.08mm or exhaust valve 0.06mm hornet ki setting bol raha hai is setting se kya dikkat aa sakta hai?

[@KISHORENAACHDANCEACADEMY]

Exhaust valve hamesha bada hona chahiye, Valve mein kachra phasega, bike starting problem or riding karte waqt missing karne lagegi or bandh hogi. Try inlet 0.07 and Exhaust 0.10 Oil 20w40 Carburetor air tuning 3 and half round Bohot smooth chalegi

[@SaiRam-yq9de]

Bro I have adjusted in my hornet inlet 0.7 and outlet 0.10 is there any problem​@@KISHORENAACHDANCEACADEMY

[@KISHORENAACHDANCEACADEMY]

@@SaiRam-yq9de no problem in valve setting .. My milega is 56-58 maintaining engine oil, and carburetor servcing in every 4 month with speed 55 to 60

[@naman0141]

​@@SaiRam-yq9de have you adjusted by yourself ?

[@Sharankumar.k]

Bro aap ne to inlet valve 0.08mm or exhaust valve 0.24 rakha hai exhaust jyada raha hai kya is se bhi bike smoot chalegi

[@aruneswarprasad5995]

Bro i have these types of sound in my hornet.... But in morning it's high. What is the problem?

[@vikasshelke5544]

Your tappets need to be tightened a bit , as engine warms up metal expands so are tappet clearance closed

[@subhan1641]

can u tell which number blades i should use, i just bought from amazon it has lots of blades and number on it

[@shahbazkhanz1]

Intek 0.08 Outlet 0.24

[@humblehostile7946]

@@shahbazkhanz1 does it provide smooth sound and run?

[@shahbazkhanz1]

Very smooth

[@rajsuthar3997]

4.54 spanner number or name?

[@aravindsnair1539]

Bro nte vandyl nine oru sound vrun oru karakarap timming chain adi onde wrkshopil kanichu apol prnju bearing complaint anen

[@pratiktotre179]

Bro make video on clean crankcase breather plz

[@KunalSharma-fo7hd]

Brother Inlet 0.08mm Exhaust 2.4 mm Was this setting ok ? Did you face any noise problem after fitment?

[@mjpavithrraraauj]

Exhaust 0.24

[@symphonyofagony2256]

inlet 0.08 mm and exhaust 0.12mm.or else after engine warm up u will get tik tik sound from tap[pet

[@rafeeqpoyilipoyiliambalil8004]

You must tell how much measurement feeler gage

[@yoyohoney700]

Bro in my hornet 160r ..when i start ...tiktik sound is coming when low rpm ....local mechanic said ..timing chain n timing pad want too change ...my bike run 14000 km ...can u pls help me

[@muhammedbinshasn2600]

Ya bro the sound is coming from the timing chain. It is a very common complaint in hornet so u need to change the timing chain. If u have warranty then go with it

[@rafeeqpoyilipoyiliambalil8004]

Not timing .....tapet sound

[@dr.sudiptachand5008]

Replace tapid from hero parts...honda will always be same

[@technicalajay5214]

After adjusting valve clearance, did you get oil linkage problem from above open part of engine cover? Request you to respond.

[@muhammedbinshasn2600]

Nop. Need to change top gasket of engine top cover. Then there is no issues like that

[@technicalajay5214]

@@muhammedbinshasn2600 thanks bro!

[@gaurabpokharel6373]

dosent have pratice enough . do it slowly otherwise you will slip some bolt and its going to have big trouble same as me

[@vishalwarale5937]

Share link of tools

[@NaseemKhan-qf7bi]

Sir my bike last speed 95 what is problem 19000km hornet 160r

[@muhammedbinshasn2600]

Chek the air filter cover, there is a rubber cover coming above the air filter if it is not properly fixed the top speed will reduce

[@NaseemKhan-qf7bi]

@@muhammedbinshasn2600 air filter is new good fitted

[@muhammedbinshasn2600]

@@NaseemKhan-qf7bi check the cover above the air filter, there is a air intake cover coming its rubber cover and there is a hole in cover means one side air passage only check that cover properly fixed or not

[@NaseemKhan-qf7bi]

@@muhammedbinshasn2600 good fixed cover and rubber

[@muhammedbinshasn2600]

@@NaseemKhan-qf7bi then try to re adjust the carburator air fuel ratio screw from lean mixture to rich mixture then try,

[@mjpavithrraraauj]

Not just any TDC. It has to be end of compression TDC.

[@mjpavithrraraauj]

At that time both rocker arms will be slightly free and not engaged with the cam profile.

[@vishalwarale5937]

What happened if it get adjusted @ exhaust stroke

[@artisticshiva4719]

How many km it ran

[@salim-iy2qv]

Bhai aapka mobile number milega kya