Valve Clearance or Tappet Setting of CG125

[@RiderRickMaker]

One thing I think is very important that you forgot to mention... you need to adjust the valves "on stroke". Get the Intake Timing T | aligned: Adjust the Intake Valve. >>> Rotate Magneto Get the Exahust Tiing T | aligned: Adjust the Exahust Valve. >>> Ready to run I think this is one of the most important steps that are missing in ALL youtube videos out there. If you adjust the Intake and Exahust on the same stroke you're in for trouble as you'll mess up all timings. Did it on my bike, now it chokes a lot, I can only fix it on the weekend and hopefuly It won't die on me as I need to make extra 300 Kms this week...

[@mustafabassim2083]

after reading your comments I'm now even more confused

[@TheRandomBiker]

Ignore him.. adjustment of tappets never effects "timing of a motorcycle" thats the job for CAM..

[@kanchankondhare]

very nice teaching best explain good work always sucsess....

[@theinternet8853]

Very well explained and shot 👏

[@johnb.9806]

Very helpful. did mine today and now it doesn't cut out any more. Btw, just fyi, it is called the magneto.

[@TheRandomBiker]

+Ardent Fan cut out means that engine shuts off on idle..

[@TheRandomBiker]

+Ardent Fan that is also true.. but valve clearence has also major part in this if vavles are tight then engine shuts off..

[@rghudasrghudas1984]

The Ra

[@timothyjameslirit3304]

k

[@diykhan]

Mashallah jee bahoot khoob.

[@maqsoodali3895]

Bhai, cg125 10 model bike ke liye guage kitna rakhon? 0.025 or 0.04 or 0.08mm? Kitna?

[@coihei3688]

...But first, the Sente setting!!!! intake.008 mm ekzost:0.08 mm Mr. Ali I made a 0.12mm exhaust but if it makes a lot of noise, if it falls off the traction, if it vibrates, you make it 0.08mm.. I hope what I wrote will work Greetings

[@irfanwazir3091]

Nicely Explained..

[@asheraziz9121]

thanks .08mm clearance both for intake and exhaust valve? ?

[@TheRandomBiker]

yes..

[@asheraziz9121]

Thanks a lot. I have aleady adjusted valves clearance for generator using feeler gauge. Now me going to adjust the valves clearance of my 125 with your help.

[@TheRandomBiker]

+Asher Aziz sure.. need any help.. contact me on my Facebook page.. Fb.com/TRBiker

[@georgeprime2249]

Exhaust should be more gap than inlet.

[@charlesbarnett2724]

Thank you. Very helpful

[@herbeline]

Bhai 125 k rocker aur raad k problm ki video nhe hy youtube py.yeh b bana do plzzzz

[@Sotonsmr]

Might wanna check your gasket cover seal. And make sure your not on exhaust stroke 360 degrees. U can also turn the fly wheel in gear on bikes with no kick saves taking the box cover off

[@TheRandomBiker]

+Craig Mintram yes it does but it is better to take the cover off

[@Sotonsmr]

The Random Biker as long as u can see the markings on the flywheel dude. I'm justvsplitting hairs good job

[@daudxee5512]

The Random Biker I have 2007 model and I have chenged its ring piston,piston etc and the tappet makes noise even if it is tightened and it's RPM is decresed to 8000-9000 from 10,000 but yeah runs as good as it was. So what is the problem

[@TheRandomBiker]

+Daud Xee tappets are over tight.. if tappets are over tightned they also make noise and rpms get limited and also rpms drops slowly when you rev it..

[@daudxee5512]

The Random Biker I should get engine checked by Honda?

[@lalizubair7840]

Bhai keHte he K new Model cg 125 k tappet ki setting 0.10 mm krNi Chahye

[@TheRandomBiker]

Brother mene new models ki workshop manual se dekha hai yehi likha va hai 0.08mm hoti hai

[@lalizubair7840]

@@TheRandomBiker HOo skTa h brOo butt Rawalpindi ka he woO BnDa 1980 Se kaM kr Rha he UsNy btaya tha k new model k Tappet 0.10 mm rkhnY ChaHye

[@jnebtv7614]

Can I do the same way on TMX 125 alpha, and the same size of feeler gauge at 0.08 mm?

[@TheRandomBiker]

Yes you can

[@dansoyinside2624]

Tnx for the video sir. But i change the tapet clearance of my tmx155 same engine of cg125. I use the 0.008mm very noisy when i start the engine. Whats the posible problem.? Tnx

[@TheRandomBiker]

Sir you should make it tighter.. you may be losing it too much.. Or else the rocker arms could be the isssue..

[@haqnawazmalik3871]

Its really helpfull..

[@saeedshaikh319]

Bhai jan meri cg k catcher bar bar nikal jaty hai jis ki waja sy valve tere hojaty hai kya waja hai me change kr kr k thak gya hn valve

[@anxioustuber]

can you make a video on how to change the clutch plates of cg 125?

[@TheRandomBiker]

+Raja Awais i can guide u how to but at the moment i don't have such cg available which needs clutch plates to be changed.. eventually i will but after some time..

[@irfankhattak434]

@@TheRandomBiker bhai ye konsa Honda model hai thanku 98 ya 99

[@PM-le2di]

Sir discover 150 cc2011 modla valve clearance?

[@jhundelosreyesjr7527]

Can you make a vedio how to tune up 125 suzuki thunder 2011 model,thank you.

[@SakibChoudhury]

how come both intake and exhaust valve have same clearance ? shouldn't the exhaust valve clearance would be more ?

[@TheRandomBiker]

In this specific model both clearances are recommended same by manufacturers.. but you are right i experimented with them and intake 0.08mm and exhaust 0.10mm performs better and soundd better..

[@ylhifam9623]

@@TheRandomBiker yes mine I set it like that 0.08mm intake and 0.10mm exhaust.

[@kevinbeere5993]

Thanks that's what I wanted to know. Great vid.👍

[@paolomarcelogalvan1938]

All kinds of motor are the same valve clearance?

[@kacperchrusciel890]

no

[@kurtpeil8433]

hi the random biker thanks for the video you properly gonna save me a trip to the mechanic, hi all, i need to adjust my valves after a ticking noise appeared suddenly, does anyone know if the nut is an h8 or h10..(or h9) i just want to get the proper tool for the job but would rather get the right one straight away than you for your help cheers

[@AliKhan-iz3gt]

Bhai knsey T pe cut baraber rakhna hai aik T pe tappet move hotey hai or aik T pe move nahi hotey ?

[@TheRandomBiker]

Yes sir wohi btaaya hai video ghor se dekhen tappets ki movement ghor se dekhen pta chal jaega..

[@khanofficial7594]

Hey brother maine .. Appny bike ke tappet tight kartaa hoon.. Leaken kuch hee time baad tappet doobara hee loose hoojatyy hain.. Oor phir aawaz aany lagtyy hain.plzz help

[@TheRandomBiker]

Ziaada tight krne se pushrods damage hoti hain or tappets lose hojate hain..

[@khanofficial7594]

@@TheRandomBiker accha tooh abhee mujhee pushrods change karny hoongyy ?

[@TheRandomBiker]

Check krwa lain

[@aqibali1885]

agy badi grari dalny se kia nuqsan hy cd 70 me

[@gamma4014]

cg 125 same engine with cg200?

[@TheRandomBiker]

+Amea Gamma approximately same.. but 200 has dual cylinders..

[@hendrikterwisschavanschelt1666]

The Random Biker not dual cilinder. I have cg250 and only 1 cilinder

[@brandonpadan8057]

Same engine but cg200 has a longer con rod,big valves & bore if compare to cg125

[@TheRandomBiker]

Obviously it has its differences but mechanisms are the same..

[@mehtabkazi6343]

Nice work

[@MunaBhai-bv3gm]

hi I have honda cg 125 model 1984 maby tell me this bike original and not plz urgent need for help

[@TheRandomBiker]

+Muna Bhai what is original?

[@MunaBhai-bv3gm]

bike 1984 model cg 125 Japanese

[@MunaBhai-bv3gm]

we have watsup I'd I send vedio and photos

[@TheRandomBiker]

+Muna Bhai kindly send them on my Facebook page.. link is in the description

[@haqnawazmalik3871]

Nice Man...

[@jasoncarthew4857]

I adjusted my vavles now i have loud tapping/knocking which wasnt there befor

[@TheRandomBiker]

Adjustment is not per requirement

[@jasoncarthew4857]

@@TheRandomBiker what do you mean buddy

[@TheRandomBiker]

You might have loosen the tappets more than 0.08mm

[@Advocate_Rahim]

very good

[@zedy.kkapole6347]

Nice

[@anxioustuber]

doesn't it makes noise at 0.08mm when engine gets heat up ?

[@TheRandomBiker]

+Raja Awais no sir it doesn't.. but note guage should not move freely after setting clearence try to insert thicker guage if thicker guage can get in there then you have done it wrong..

[@anxioustuber]

The Random Biker bro I changed the tappet plate but it still makes noise rockers are also new I don't understand why it is making that noise

[@TheRandomBiker]

+Raja Awais which type of noise.. tappet sound is mild sound titch titch sound may be it is not even tappets..

[@anxioustuber]

The Random Biker everything is replaced with new parts bcz I got my engine renewed and altered maybe it is bcz of thick oil I use 20-50w

[@TheRandomBiker]

+Raja Awais oil video in progress.. oils doesn't cause sounds higher viscosity oils stop sounds..

[@tayyabnaveed2266]

Where can I buy that feeler guage in Pakistan?

[@TheRandomBiker]

+Tayyab Naveed from any auto shop

[@DOCTOR6423]

Tayyab Naveed you can buy it from plaza market bundar road shop name zubain impex if you buy Taiwan brand its cost 1000/=

[@DOCTOR6423]

Tayyab Naveed filler guage or tappet guage

[@TheRandomBiker]

Naa bro its only 250pkr or 350max.. Taiwan brand

[@usmankhalid6798]

Great g

[@shahzadkhan2745]

Good luck

[@alishah1191]

please sir more video

[@TheRandomBiker]

+ali shah what sir?

[@muhammadamanullah4123]

Salam guys Meray pass honda cg 125 2017 model hai first oil change maine 250 pe karwaya tha aur havoilne 20-50 dalwaya tha... Abhi bike 500 km he hui hai aur 10-15 min chalanay ke baad he bike band hp jati hai khud ba khud mai mechanic ke pass lekar gya tow us ustad ne kaha tapets bohat tyt thay usnay tapets loose kiye and then maine test le phir bhi bike baar baar band ho rahi thi.... Then usne carb khol kar petrol se clean kiya aur NGK ka iridium plug lagaya magar ussay bhi koi farak nhi para magar mujhe bike ke performance mai wazeh farak laga us ke baad bike kafi halki ho gaye... App log zara mashwara dein ke yeh problem kyun paish aye... Aur mera ustad khari bike mai accelerator de rha tha woh aisa kyun kar raha tha?? And mai apni bike ke bohat care karta hun shell ka vpower + normal petrol mix dalwata hun and ajj tak kabhi apni bike mai max 60 se upar nhi lekar gya.. App log mujhe batayen ke running kaise karni chehye bike ke plz thora guide karin im a new biker.

[@repiiedits7932]

Bhai I also That Problem. tunning Se thek hoga And nuts Ko tight Kro

[@repiiedits7932]

Values Zyada Tight ho to Engine khud he shutt off hojata he

[@muhammadamanullah4123]

Thanks Man

[@mehtabkazi6343]

Cg 125 model 1991 Japan sealed engine for sale in Pakistan converted only body part 2017

[@ekghostofficial]

Bhai music ki bjaye bolty to btr tha

[@georgeprime2249]

It would be better to see what's happening without all the writing blocking things.

[@kamranhayat5897]

My cg125 honda is 2004 model.driven only 24000km.till 50 speed sounds perfect but as above 50 a sound of ghmmmmmm starts coming out of engine.please tell me whats the reason.mechanic changes clutch plates still not solved.hope you help me

[@TheRandomBiker]

Brother apki transmission main gear koi daagh wali hai.. damaged yaani k.. Ye awaz just 4th gear me aati hai agr to tb..

[@kamranhayat5897]

The Random Biker thanks for reply.i will check tomorow k 3rd gear ma bhi awaz hai ya nahi

[@sapader]

hard starting na me gasgas pa camfollower

[@janbiellamadridlopez4789]

natitikal ko ang magnito cov0er ng hindi kaylangan alisin ang kambyo

[@TheRandomBiker]

+Janbiel Lamadrid Lopez english please..

[@noridada4562]

ليس هناك وضوح في المعلومات

[@TheRandomBiker]

+Nori Dada what?

[@ghiemon7401]

hello, can someone help me how to replace the Oring in here ☝

[@TheRandomBiker]

ghiemon i can help please specify..

[@TheRandomBiker]

+ghiemon please specify i can help u

[@MunaBhai-bv3gm]

we have watsup I'd I send vedio and photos my bike

[@mindtohart8775]

I have dailem vs 125 i want larning full repair engine how it's my mail [e-mail]

[@alisonambridge8832]

G

[@farhanqureshi1921]

U have to more learn baby

[@TheRandomBiker]

Yap 😀

[@aqibali1885]

ji