VALVE & INJECTOR ADJUSTMENT FOR CUMMINS KTA19-G4 (PART 2)

[@siseniobalio8262]

Salamat sir sa pag share ng kaalaman mo.. more blessings and good health God bless.

[@bobbyguana8812]

Boss pwedi mo rin ba ipakita kong paano mg change out nang fuel valve? Thanks

[@yhongardsofficial5329]

Salamat sir, sa pag share ng inyong kaalaman. God bless po. Ingat po kayo jan..

[@bangmechanic]

Salamat sir,GOD BLESS...

[@nelsonbanusong6261]

Salamat sir kasabot na gamay hehehe believe ko

[@jamesstrong6685]

Magandang araw jan chief. Pwede bigyan mo ako kung paano mag adjust ng injectors at valves ng kta19-g2 at torque sa vibration dumper chief. Thanks & God Bless always chief.

[@bangmechanic]

Halu sir,torque sa dumped pulley (445 Nm) (330 ft-lb) Pulley injector valve A-------- 4---------5 B-----‐--- 1---------3 C--------- 5---------6 A--------- 3---------2 B--------- 6-------- 4 C--------- 2-------- 1

[@bangmechanic]

Sir sundan mo lang, STC (OBC)INJECTOR ANG GINAWA MO BOSS?

[@bangmechanic]

Torque as injctor 90 in-lb

[@jamesstrong6685]

Chief parang sa G4 ito, ung para sa G2 chief? Tnx

[@jamesstrong6685]

Chief pwede lng ba ung torque method ng kta19-g4 gamitin sa kta19-g2?

[@michaelmulto8013]

Gawa ka din ng video sir nung dial indicator method, Di pa nakakabit mga racker arm

[@SegfridVersaga]

Goodpm sir pareho lang po ba yan ng kta19-m4 ang adjust sa valve at injector.?

[@MorristulaleGajardo]

pm po sir yong KTA19 saka KTA19-G4 same lang po vah yong adjusment nang valve saka njector?

[@elmoespocia9730]

pagwalang torck wrentch na my gauge pwede ba mag ajust ng injector at post rod ano gagawin po

[@robertopacheco2420]

Sir Good day ask lang po ako same lang ba sila ng KTAA19-G6A valve and injector adjustment?

[@alghifarifamschannel749]

Om maaf mau nanya, Kalau Cummins KtA 19 oli mix diesel oil biasa penyebab nya dari injector ya om, saya sudah ganti Fuel pump dan check ganti o ring pipa minyak yg dari fuel pump memuju ke head lalu ke injector

[@simongipsyzai6130]

Hello sir , amazing video May I know , how to determine when we use OBC or IBC and when we use Torque or dial gauge to adjust Injector . Thanks sir , 🙏🏿

[@bangmechanic]

Usually if it is STC injector or OBC, you use torque method.

[@simongipsyzai6130]

@@bangmechanic okey sir , thank you sir . 🙏🏿

[@michaelmulto8013]

​@@bangmechanicsir más madali pa tune up ang KT38 at KT50 yung pulley nya meron ng marking kung alin dapat mo set ng injector at valve di tulad sa NTA855 at KT19 minsan malito yung Di pa gaano familiar sa Cummins madami ako naencounter kahit calibration center sumuko

[@redenora7840]

​@@michaelmulto8013depende sa series yan brod,kaya dapat alam mo kung anung series ginagawa mo,para di ka din mahirapan,sa injector naman meron tayong mechanical at electronics,ang electronics kasi ET na gamit kailangan marunong ka mag trim injector,

[@lastonkuluunda480]

Your demonstration is very good keep it up

[@bangmechanic]

THANK YOU...

[@rickygorospe2304t]

Gago mali ung tinuturo mong pag adjust tanga ka magtuturo ka mali pa gaho

[@josebalbuena5038]

Kabayan saan ka dito sa saudi nag work .ako Po dito ako sa Dammam

[@matiiassardina1559]

Hola buen día, mi pregunta es si un KTAA19 G8 es lo mismo que un G4? Y en el caso que es asi, podria por favor escribirme que valvulas y que inyectores se ajustan en las marcas A, B y C. Muchas gracias 😊

[@abdrahman2122]

what is the fuller size for cummins engine valve adjustment

[@mikhailatsea]

What is clearance of intake and exhaust valve ?

[@danafitria5175]

Ass bos apa penyebab asap kluar dr water cooler n tmperatur naik mesin kt 19

[@thexshan2095]

Why, cummins k19, manual start ok, remote start Hunting??

[@leirayvanahisarza602]

Sir pinapanuod ko po Ang vedeo nyo..pwede Po mgtanung Kong anung mga interview Po kung aaply Po Ako ng Cummins s Saudi?bale mga makina lng Po ng Japan inooverhaul ko dto sa pinas..slamat.

[@bangmechanic]

Sir dependi kasi sa company anong itanong.thank GOD BLESS...

[@romeoporleytv2720]

Kabayan, pwede pwede bang makahingi ng tamang adjust ng injector ng cummins NTA855, yong pagkakakasunod? Kc ginagawa ko tantsahan nalang pag hindi mausok yon na, degree lang ginagamit ko, salamat kabayan,

[@marladiploma185]

Boss ptlong ako d60p-6 Cummins komatzu 153624 firing order ng injector kpg ng adjust ako ng valve clearance..ano running mate sa valve ng injector kpg ng adjust na ako ng UNO..

[@bangmechanic]

Pulley(F.O) (VALVE)(INJECTOR) A--1-6VS---1----5-----------3 B--2-5VS---5----3-----------6 C--3-4VS---3----6-----------5 A--6-1VS---6----2-----------4 B--5-2VS---2----4-----------1 C--4-3VS---4----1-----------5 Boss,sundan mo pag nag adjust ka sa valve&injector Torque sa injector 72 inch ft..

[@bangmechanic]

Boss sorry na double ang 5 sa injector (3-6-2-4-1-5)

[@ROMEOPORLEY-xo7dl]

Parehas sir yan ng adjust ng KTA19-c525 ? Ganyan din marking sa pulley.ilan sir clearance ng valve.salamat

[@bangmechanic]

Valve clearance (INTAKE. 014")(Exhaust .027")

[@ROMEOPORLEY-xo7dl]

Kta19-G4 at KTA19- C525 sir iisa ang adjust sa injector at valve at sa pulley? Salamat sir

[@kefelegnasfaw7475]

Hi Bro how u doing can we use both torque method and dial indicator at z same engine so that z results same

[@maqsoodalidasti9981]

Cummins 16 cylinder ka valve adjustment dikhen

[@jamesstrong6685]

Magandang araw jan chief, ask lng ko ano bolt size sa conrod og main bearing sa kta19-g2 12 points ba chief? Tnx

[@bangmechanic]

Sa conrad 12point sa main bearing 2type 12point &six ppint

[@jamesstrong6685]

@@bangmechanic ano size sa socket wrench chief? Tnx

[@bangmechanic]

@@jamesstrong6685 sa Conrod bolt 11/16 socket sa main bolt 12p0int 1" sa 6point 1-1/2"

[@jamesstrong6685]

@@bangmechanic Many thanks chief & God Bless always.

[@bangmechanic]

@@jamesstrong6685 welcome GOD BLESS YOU TOO...

[@alexandercolmenares8561]

Buen día, necesito calibrar un KTA19-G6, mi pregunta es: es igual al KTA19-G4?

[@britofigueiredo]

Olá tudo bem sou Raimundo Brito, Brasil de onde vc é meu amigo

[@jonathanbajinting6042]

Good day sir tanong lng ko sir adjast s cumins big cam 315 valve Ang injictor salamat

[@bangmechanic]

Nice day sir,engine model cummins NTA855 bigcam ginawa mo?dami kasi model ...GOD BLESS..

[@michaelmulto8013]

Yung Ibang KT19 ang injector torque 6 inch pounds

[@regiewaquiz1916]

Sir panu q po i-set ung dial torque wrench sa 0.678N.m ganung ang bilang lng na meron eh 10-100N.m lng po?

[@bangmechanic]

Sir meron torque wrench special para sa injector yong inch pound na torque maliit.GOD BLESS..

[@bangmechanic]

Sir gamit ka torque inch pound. Thank you

[@regiewaquiz1916]

Salamat boss

[@bangmechanic]

@@regiewaquiz1916 welcome sir GOD BLESS

[@ngoccanle1645]

please let me know how much is the gap between the wind suppap and the fire suppap. Please answer for me

[@bangmechanic]

Valve CLEARANCE Intake valve (36 mm)(14") Exhaust valve (69mm)(27")

[@elmerbautista3609]

eto mas malinaw ngayon igan...comprende

[@javadmirzaei6525]

Hi mr...please valve and injector adjastimend cummins qsk19.please please

[@bangmechanic]

Valve CLEARANCE INTAKE valve (36mm)(14") EXHAUST valve (69mm)(27") Injector 90inche pound

[@frederickbernas3697]

Hi ung procedures nio po b ay standard or merun pang short method

[@bangmechanic]

Sir,standard po...

[@DieselGeneratortraining]

❤ from #Power Learning Channel

[@bangmechanic]

Thank You Sir more Power keep safe always..

[@engryunusyahaya140]

I'm having problem of red hot

[@sandyfortuno3194]

Sir. Maayung gabie. Paano malaman kung naka tdc na ang valve 5?

[@bangmechanic]

Sir nakalagay sa pulley mark A-2&5 VS.

[@criscarillo9868]

Sir tanong lng po..kc ang gnagwa ko sa kt19 ung top stop method..may pinagkaiba b yon..

[@bangmechanic]

Sir anong klase na injector STC?

[@junvilloson7577]

thank you boss ingat kau dyan

[@tekingzvlog]

salamat sa pagshare bos

[@danielnecesario8327]

Puydi makatingin ng video mo sa pag tanggal ng ringer ng KTA90?

[@bangmechanic]

Sir dalawang klase ang flywheel ringer sa KTA.may klase na pwede palitan.initin mo lang sabay pokpok matatangal yan ganon din pagkabit initin.thank you sir GOD BLESS....

[@josephautida6247]

Boss mangutana lng ko boss..pwdi ra fellar Gauge gamiton pagkuha sa injector clearance adjustment..ug pila akong hatag...salamat sa tubag idol..

[@bangmechanic]

Boss dili pwede gamiton feller gauge pag adjust sa injector.gamit gyud ka special tools para balance. Thanks GOD BLESS..

[@bangmechanic]

Yes sir,gamit gyud ka special tools para balance...

[@bangmechanic]

CUMMINS KTA19 torque 90 ins lb.

[@javadmirzaei6525]

Hi.please calibrtion motor cummins qsk19 .please please please

[@drubchohan1712]

Very nice job.

[@bangmechanic]

Thank you GOD BLESS...

[@charlesemmanantigolas.6821]

💖👏🏻

[@malayangmechanic1269]

Meron ba paraan nyan na di na gumamit ng inchpound na torque wrench?

[@bangmechanic]

Dapat talaga boss gamitan ng torque para balance lahat yon kasi require.sa CUMMINS...

[@malayangmechanic1269]

@@bangmechanic boss pahingi ng para sa VTA28-G5 valve and injector setting adjustment

[@bangmechanic]

@@malayangmechanic1269 VTA28-G5 VALVE CLEARANCE INTAKE 14"(36MM) EXHAUST 27"(69MM) INJECTOR TORQUE 70 INCH FOUNDS.SABAY SIYA SA PAG ADJUST SA VALVE &INJECTOR TINGNAN MO LANG TIMING MARK SA PULLEY LEFT BANK&RIGHT BANK..

[@romeoporleytv2720]

Sir, pwede sa sunod, NTA855 big cam naman, salamat

[@leonardomendoza3358]

Buen día oye cómo puedo conseguir combustible de inyectores y alturas de inyectores también calibración de bomba de inyección

[@michaelestonanto7454]

Boss thanks po. Ask ko lng po kung pede din po b yan sa KTA19-G2 big cam

[@bangmechanic]

Pwede sir basta STC ang injector..

[@venersalita5130]

Bosing same lang puba ang pag chune sa ktaa19g7?

[@bangmechanic]

Same lang sir,basta STC

[@daisysalita1108]

Sir anu pong dialmetod ng ktaa19 sa injector wala papo kc ako torquewrenc.

[@daisysalita1108]

Ktaa19g7

[@bangmechanic]

@@daisysalita1108 Sir, ang Dial method as KTA19 normal injector gamit ka DIAL indicator(0.304")adjustment. SA KTA19 G3-G4 UP Gamit ka torque method (90 ins pound)gaya mg ginamit ko sa video. THANK YOU GOD BLESS...

[@bangmechanic]

@@daisysalita1108 Sir,may video ako KTA38-G2 gamit ko dial indicator.paki view sir thank you.

[@OrlandoGonzales-hj2ey]

Good job idol

[@guidofredosolamillo4593]

May firing order din Ang pag adjust ng injector ,Ilan Ang clearance NG Injector ok salamat

[@bangmechanic]

Sir meron sundin mo lang ang sequenced sa pag adjust ng valve&injector sa valve 5-3-6-2-4-1 sa injector 4-1-5-3-6-2 KTA19-G4

[@bangmechanic]

SA VALVE CLEARANCE INTAKE (36MM SA INCHES 14")(69MM SA INCHES 27")(SA INJECTOR 90"founds)

[@bangmechanic]

EXHAUST 69MM/27"

[@anicetosalve6772]

Bkt prang bakiktad .hndi ba dpat pg nka top ung cylinder #1 sa #5 ung valve at #3 ung injector....prang backward ung sau boss...d ok at advanced db

[@bangmechanic]

Sir 2 type ang adjustment sa KTA19.THANK YOU &GOD BLESS..

[@JerryGenoveza]

Boss good am

[@ipunksuneo]

Thank u broo...

[@ManongFriends]

Lupet mo tlga foreman

[@aslamahmad7856]

Injakter kitne pr tork hoga

[@criscarillo9868]

Apply nga ako jan boss magkano b bigayan sa company nyo? Galing din akong Saudi..

[@bangmechanic]

Ok sir pag mag hire company...

[@criscarillo9868]

@@bangmechanic salamat sir..

[@bangmechanic]

@@criscarillo9868 welcome...

[@michaelestonanto7454]

Boss salamat po...ano po UNG stc

[@bangmechanic]

Hello sir, step timing control

[@evangelinebetorico82]

Sir paano mg aply jn

[@engryunusyahaya140]

I need the injectors setting

[@manueldelgado4609]

Tanks po chef

[@Deep_Jani]

Very well

[@regiewaquiz1916]

Bale NTA855 ang ina-adjust q

[@bangmechanic]

Sir,dalawang klase ang injector sa NTA855 STC&NORMAL INJECTOR.

[@regiewaquiz1916]

Halimbawa sir STC po xa?

[@bangmechanic]

@@regiewaquiz1916pwede hindi kana gamit torque ikotin mo adjusting screw dahan dahan paglapat na medyo nakadiin tama na.kasi TOP STOP ANG TAWAG SIR

[@bangmechanic]

@@regiewaquiz1916 sir TOP STOP ang tawag kasi paglapat sa rocker arm sa injector STOP kana konting pihit lang sir dapat pariha lahat.kasi 0.678 napakalit .

[@regiewaquiz1916]

@@bangmechanic ganyan nga po ung ginamit q method today pero ayaw maniwala ng chief mechanic na ok ung injectors q..ayaw mawala ng puting usok

[@azilfaulve-bb9rz]

Paano patayin Ang commens bos

[@kalamansari3637]

Very good I like you

[@bangmechanic]

Thank you...

[@ngoccanle1645]

Cho cháu hỏi khe hở suppap là bao nhiêu ạ

[@javadmirzaei6525]

Please please qsk19

[@sonvo2274]

Cho em xin sơ đồ chỉnh được ko

[@bangmechanic]

My apology sir for I can't understand your language / dialect. GOD bless!

[@donnamaebulay6697]

Pa shotout boss babang

[@ashrafaliali5467]

sadik ATI no mobile

[@ruelcampaner2416]

500hp na cya boss

[@jamilhossain9821]

Got

[@mahibamba1355]

Moteur cuimice qui chauffe

[@VirgilioArtienda]

Not well explained