Thanks Acoem USA for sharing this video. It is much appreciated.
@AcoemUSA8 ай бұрын
@Granahe501 Thank you for watching!
@waleneliyata12527 ай бұрын
Can you explane how shuld we ajust belt.. How to find that set point
@AcoemUSA7 ай бұрын
@@waleneliyata1252 Loosen the motor-side bolts, move it accordingly (in the direction that you need to go), tighten the bolts, and then re-check.
@barbarakrawczyk32486 ай бұрын
@@AcoemUSA How to check the linearity and alignment of pulleys in a car? Can AT-400 do this?
@AcoemUSA6 ай бұрын
@@barbarakrawczyk3248 The AT-400 is designed for performing shaft alignments of direct coupled machines and is not used for belt drives. Our Belt Hog is designed to perform pulley/sheave alignment of V-Belt driven machines. There are also adapters available to align Positive Drive/Synchronous Belts and Sprockets. Most vehicles today use serpentine belts, which the Belt Hog adapters aren't designed for. If your vehicle does have V-belts there may not be enough clearance for the Belt Hog to fit. If it's a larger vehicle like a bus it's possible the Belt Hog MAY fit. Here's a link to a blog showing Belt Hogs being used for V-belt alignment on buses. acoem.us/blog/belt-alignment/belt-hog-busses/
@emmanuelphiri20865 ай бұрын
Perfect explanation, thanks, also include source of the tools you are using in the description
@AcoemUSA5 ай бұрын
No problem @emmanuelphiri2086 ! Thank you for watching.
@IXtreMI5 ай бұрын
Nice video very helpful thank you! I have a laser alignment tool and i searching a another tool than the frequence meter to measure the tension of the belt (little expensive). I can't find the app you mention on the google store do you have a another link to it please ?! I live in UE. Thank you Best regards
@AcoemUSA5 ай бұрын
Thank you, we are glad that the video helped! Are you using an Android or Apple device to download it? If you are on Android, you may be able to download the app from this page and download it to your device: browning-power-transmission-solutions.en.aptoide.com/app
@washington_pc33063 ай бұрын
Cool Video. Where can we get this tool?
@AcoemUSA3 ай бұрын
Thanks! You should be able to find them on Grainger or Amazon. Browning makes one that we would recommend!
@ofeelma2 ай бұрын
What is causing all the teeth to shred off my v belts? Are they too tight
@AcoemUSA2 ай бұрын
If you are referring to timing (synchronous) belts, there can be several causes of the teeth failing: 1. Misalignment and improper belt tension too loose or tight can cause belt failure and should be checked/corrected first. Use one of the available laser sheave/pulley alignment tools to check the alignment. A string or straight edge is not accurate enough as allowable misalignment is only 1/32" per foot of length between the shaft centerlines. Check and adjust the belt tension using a spring or sonic tensioner. The timing belt manufacturer will specify how much force is required for the amount of deflection based on the belt size. 2. Timing belts have either trapezoidal or curvilinear tooth profiles that mesh with profiles in the sheave like a gear. Check the tooth profiles of the sheaves, worn profiles can cause early belt failure even with a new belt. Also check that the belt and sheave profiles match. Did a sheave get replaced with one with an incorrect tooth profile or pitch diameter? Also timing belt sheaves should be replaced more frequently then V-belt sheaves due to the tolerances between belt and sheave tooth profiles. 3. Did the timing belt wear "normally" before? If so, what changed in the process? Is it running at higher RPM's? Was a larger motor installed? Does a change in the process require more torque? If so, then a change in the belt size is more than likely needed. Hope this helps!