A quick overview on how to service a Volvo-Penta SX-M outdrive.
Пікірлер: 31
@ThailandAmazing3 жыл бұрын
Thanks. I’m about to do this first time
@whatthechuck31143 жыл бұрын
Good luck!
@searay260sundeckforsale411 ай бұрын
Identical process to my Mercruiser Bravo 3 outdrive!
@freshsaltyfries5078Ай бұрын
Hey chuck I’m getting ready to do the same. So any swivel socket set would work? Do you know the size of the sockets used metric or sae?
@jsboening2 жыл бұрын
My manual says to use light oil on the drive shaft O-ring seals and not grease. The heavier grease can cause an airlock making it difficult to install the drive.
@whatthechuck31142 жыл бұрын
I use spline grease and have not had an issue.
@nathanherbst14253 жыл бұрын
Thanks for the video, I'm about to take mine off, I hit a rock and now I have nothing in forward or reverse. I can spin the prop by hand in forward, neutral, and reverse (engine off of course), any idea on what normally fails?
@whatthechuck31143 жыл бұрын
I would check the cable first. Quick and easy
@drv2e304 ай бұрын
Hi! Did you buy all of those parts in a kit? If so could you leave a link?
@TheLtrentlage3 жыл бұрын
Could the penta sx model m lower unit be dropped in place on the boat? (The lower gear failed on the vertical shaft), Or does it require any disassembly of the upper unit to fix this issue?
@whatthechuck31143 жыл бұрын
Yes it can. Remember to drain the oil and be careful lining everything up with new seals when putting it back together. 👍
@ProfessionalDad2 жыл бұрын
is there a way to deal with the coolant hose and components without removing the whole outdrive? Maybe just the bottom?
@whatthechuck31142 жыл бұрын
It’s really tight. I would just pull the drive
@TheLtrentlage3 жыл бұрын
Is there zerk grease fittings on the u joints or is it just the shaft that needs grease?
@whatthechuck31143 жыл бұрын
Some have them. Mine do not. The shaft should get fresh grease and new o-rings.
@pedrovillarreal35484 жыл бұрын
My outdrive wont go down any suggestion on what could cause this its 2001 glastron 4.3 GL Volvo penta thanks in advance..
@whatthechuck31144 жыл бұрын
I would start with fluid level and then make sure the pump is getting power. Check the switch etc
@adriannino6604 жыл бұрын
Hey Budd. What you torque the stern bolts to
@whatthechuck31144 жыл бұрын
If it’s the six that hold the drive on- 25# initially and then 50#
@goproexplo92903 жыл бұрын
Nice Video. I need some help, i got the leg off 100%, when i took the pin out for the trim rams, one ram compressed and the other lengthened. I felt to see if i could push and pull and they seem solid, Why has this happened? How do i get them free to move to line them up? Thanks
@whatthechuck31143 жыл бұрын
Have you tried running the drive up and down with the switch?
@gregbolles7170Ай бұрын
You should be able to lift the outdrive by hand to line up one ram and put the pin half way through. Then lift the drive by hand some more to line up the other ram and push the pin all the through the lined-up rams. It's a two person job to do the lifting and lining up.
@colinmatijevich43242 жыл бұрын
Hey any chance your lower unit had a steering trim fin? My boat doesn’t turn but has a good lean to the left when I go up on plane and the only thing I can find online is to adjust the trim fin but mine doesn’t have one any advice before I buy a 70 dollar chunk of Metal that may or may not help
@whatthechuck31142 жыл бұрын
Mine does not have one. On occasion it will lean to the left as well. It is a common issue and most people turn in the opposite direction to straighten it out. I believe it’s more of a weight balance problem than a steering problem. Those chunks of metal also serve as a sacrificial metal for corrosion. Mainly for salt water. I just adjust the people in the boat.
@seadoopilot5378 Жыл бұрын
No fin or tabs?
@AchikSarih4 ай бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
@dukelps9132 Жыл бұрын
Are there oil fill plugs on the foot and the upper unit?
@whatthechuck3114 Жыл бұрын
On this drive you fill from the bottom plug until it comes out of the top.
@LoneWolfSnowplowing Жыл бұрын
@@whatthechuck3114 you probably want to be specific and say fill until it comes out the side. top would be the dipstick hole to some, unless the SX-M is different from SX-A and others.
@mattbodenheimer41932 жыл бұрын
Do you have to have the Line up tool because mine went in without it but does have a small knock