VW and Audi Throttle Body Adaption and Realignment

[@tedjohnson64]

Excellent presentation! I esp. liked the way the VCDS screen was displayed so clearly.

[@YourFavouriteComment]

Thanks i ended up referring to the rosstech wiki but your video gave me an idea what to do. Fixed my startup issues in cold weather

[@maxmantix]

Thank you bro. It's a few minutes to midnight and I just had to fix my Mk4 coz I could not wait till morning. It worked!

[@gregorytoddsmith9744]

Get an ANCEL VD500 OBDII from Amazon for $75. It will play with a Volkswagen, Audi, etc. or American OBD systems. Plug into the port under the steering wheel. Key on. Select the read function for V/A diagnostic protocols. Don't try to start. Dial up the throttle body function. Field one relearn. Field two relearn. Third field it might stall awaiting information. If it does turn the key to start and it should start and smooth right out. That is providing you have a clean (pull it and spray it clean with carb cleaner) free of defects throttle body. If it was running fine and your battery died or you disconnected it for some reason you might experience a start and stop condition. No laptop or expensive software required. Happy motoring!!

[@MitziedosSantos]

This was so helpful. My 2002 1.8T began to idle weird. The throttle body and battery was removed one week ago. Tomorrow I will have this done.

[@jamesmorgan9707]

I was just about to start dancing then I stopped. Thanks for this. Just got vcds to very handy video.

[@mrrobertwolfiii1079]

Appreciate you for this videos. Hello from Colorado

[@Orangelemonblue]

Im just getting “Error" on the 098 (cable throttle) adjustment field. Error code G187...just successfully replaced the Throttle Body on a 1999 Eurovan

[@ALECDRAY]

what cable did you use to link the two?

[@scotspie501douglas7]

hi do you have a licence for the VCDS Lite I have tried it but not allowed as not licenced

[@simonstergaard]

Nice. Clear instructions. Thankyou.

[@BadAsShortGuy]

hello! thank you for the video! i have a Mac tools MDT 10 and i need to input the group for the crank position sensor relearn. what would be very helpful would be a list of all groups and corresponding test. or somewhere i may find that. thanks!

[@-Gunnarsson-]

I have another question. Iv got a vw lupo from 2001. I would like to have a steeringwheel like the one you have. Is it possible it may fit?

[@Keplerr22b]

Usefull video, but forgot to note that you need to register vcds lite for about $99, if you want to do this alignment. It is not a low badget way for cleaning the throttle body, so let's do that chicken dance:)

[@2CleverInnovations]

Very helpful video, thank you for that! Can you please tell me what model of VCDS - VAG-COM are you using, I tried a few clone ones but it won't load, says gateway not supported and vcds modules software down load? Thanks for the info

[@HAM-CU7BE]

Hi. I have a Seat ibiza 1.4 TSi 6j cupra, BocaNegrA version with 180hp. Original. I m doing the replacement of that throttle. But I also have to replace the other one behind . Exactly behind of that black plastic throttle, theres another metal throttle. So How can I differentiate the alignment from the plastic throttle to the metal throttle with VCDS and vagcom??

[@emilyx1199]

Advise please. After fitting two throttle bodies on idle the engine is seems to be idling at a strange level. Pressing the accelerator it revs and seems to stick. Same thing on both throttle bodies. Can it help? Thanks

[@bautistap8515]

Hello. I would be very grateful if you could help. I got a 17' V8 FSI Touareg, bougth used and battery has been changed/disconnected for a while. Throttle pedal doesnt seem linear... If you press it a bit, it wont get going, checked with obd scanner and pressing an inch on the gas, will almost not move the relative throttle position. However, if I press halfway down, and then press it down an inch or so, it will definitely make a difference. By this I mean, when using it normally and accelerating after parking, or at a red light, I really have to press down on the gas to get moving. I compared relative throttle position with my VW Golf and pressing just a bit will change relative throttle. My treg feels very "unsensitive/unlinear". My mechanic supposedly did Throttle body adaptation. any other ideas?

[@NietVerantwoordelijkTV]

Is it also channel 060 for a mk5 golf gti?

[@Villiyey]

Hey All I have been battling with my 2005 Polo 1.6 (9N3). It starts immediately (with accelerator pressed I always start it like this). It will idle fine with no problem but as soon as I release the accelerator it idles funny for few seconds and then switches off. I took it to a local mechanic and he did a full service ( spark plugs, oil and air filter, oil change) and I also replaced the battery but the problem still persists. Please help It has had this issue for months now and have lost the joy of owning a car.

[@Daichimor]

Hola amigo, quisiera saber si estos mismos parámetros sirven para un Audi TT MK1(8N), pues tengo el mismo problema, muchas gracias 🙏…!!!!

[@Nohandleneeded101]

Hi, excellent How to. I have a golf plus 09 (family car) and trying to add a auto door lock via vcds and I have changed the coding and pressed do it. It says it has accepted the new code but it haven’t implemented it, any thoughts please? Subbed 👍🏻

[@onizukathegame4808]

Hey! Can i check vcds lite ignition coil? I have 1.8t leon 1m

[@armandopanares3685]

Where did you get 9600 from?

[@abk-autohexzakari4006]

Hello friend please i need help for my autel running in regulation ac compressor error

[@ricardoquaresma6701]

What code should I enter in my 98 polo doch motor vehicle? 060 the same?

[@mikal_1]

Very nice. I've heard the VCDS-lite couldn't do anything else than read codes, i suppose that is not true after seeing this video

[@eddgiles]

Can I do the same with a 2010 GTI (mk6) ??? Also, where can I download the Vcds software ??? Any input will be greatly appreciated

[@roberthart7237]

hi nice video can you tell me what cable i need to plug in to laptop and the car please thank i have a vw passat vr5 2.3 1999 thanks look foeward hearing from you

[@burningbelow4424]

Will the same thing work for an Audi A4?

[@itchinforfishin8038]

where can I purchase that vag com system

[@mrlntejada]

I got the vcds lite and i keep getting the same message Too many communications errors to continue How can i fix it?

[@techclub8528]

mrlntejada trying changing the baud to 9600

[@mrlntejada]

Dan's Miata i did but not luck

[@techclub8528]

try turning off any anti virus software. make sure all doors are unlocked and don't power the laptop off the car

[@techclub8528]

let me know what it was if you sort it. thanks

[@mrlntejada]

I try changing the ecu now car starts and idle but irregular i try to use the vag com to reset the throttle and i get the message no response from controller

[@mattlustig3564]

What engine was this performed on?

[@bojanjokanovic2704]

How much is open thr. Body on idle? I have golf 5 2.0fsi and 11% open thr. Body, is that ok

[@robertmadalinmitran8153]

Thank you! Works on fabia 1 1.4 petrol 74kw

[@alexandrefelippe]

Hello! I'm trying to perform the thottle body adaptation on my Brazilian VW UP TSI using the new VCDS version V22.3.1 for win11 but I can't find the option anywere! Maybe they removed this option from this version or changed the option to another place?

[@lukacvijeta]

Hello, do you find this option?

[@lorenzodavis1735]

What cable do I need to get for 08 A5 3.2 quattro

[@edapl898]

Does it work with a gti 98 mk3?

[@TUBEYOUTHETUBE]

What about vehicles with cable throttle? Is this a different procedure?

[@techclub8528]

I presume it would be. this procedure is so the alignment of the throttle body flap matches the pressing of the paddle as the signal is sent electronically

[@marcuselon]

where can i get the program

[@muratsol2679]

hey thanks for great video i have epc and check engine light plus, loss of power engine so i cant drive my car i will fix throttle body soon so is that software which u used for reprogram is that free can i download it to my laptop and i have port for connecting to car like a d can scan cable is that works thnks?

[@corneliosilguero2010]

Where you able to fix it ? I have the same problem with my PASSAT 2009

[@muratsol2679]

Cornelio Silguero i fixed, the problem was ignition coil and spark plug.. make sure use oem genius vw parts and change all together .. have you changed?

[@corneliosilguero2010]

boksu Lee i have an EPC Light but apparently it’s the Throttle Body Sensor

[@muratsol2679]

Cornelio Silguero i got same light too when i had issues so i don’t think throttle is bad.. first check your spark plug and ignition coil..

[@muratsol2679]

@@corneliosilguero2010 did you the find the problem?

[@venezia7252]

very nice best reset i have ever seen,, thanks man. just need to get the software i hope

[@fpolgar2000igor]

does any one know how to rise idle RPM on the POLO MK4, RossTech page say go to engine, adaptation, ch1 and put value between 124 and 132 in my car is value 170 i change it to 132, 200, some random number and RPM are always the same, any proposal? i have aftermarket alternator and i need 100 rpm more to charge on idle now is 670 rpm and i need 800 rpm

[@johnbeechy2913]

Great video thanks for showing

[@akoks85]

thank you man nice and easy video keep in that way ;)

[@GameOnMe]

this is complicated where you get those numbers from

[@2008freetime]

Thanks but I thought you have a different way to adapt the thurttle body to the car. No everyone has a laptop with vcds cable

[@markennyee]

Made it look so simple 👍👍 but was it a genuine Ross tech lead or a Amazon /Ebay one ?

[@s0l0t3pl4n]

Very nice vid mate. Lots of help. T.y

[@daviddart400]

Getting no response from controller hen I click on engine.

[@georgemijatovic4060]

Thank you very much!

[@georgemijatovic4060]

😊😊😊😊😊

[@shawnlibby675]

where can I buy that blue ECU cord you got

[@theokriel744]

On the WISH app, I got mine from there and worked well.

[@cayilo2]

Thank you ggg.

[@zbigniewrichard8291]

One other prerequisite is to have no electrical consumers. Sadly, cars with DRL lights have them on with the key ON. Now what?

[@aveirozinou2919]

the official ross-tech site said : wait 30 sec after you see the ADP.OK before u click done, go back , good luck people :)

[@jakeblargh]

1:19 LOL I love this.

[@proctormod]

Thanks mate!

[@emmahgeorge2106]

i love this

[@SithaSek]

well explained.

[@riosupescu]

great... thanks a lot...

[@xtrpn8636]

Love how dude didnt tell us we gotta pay $99 Just to use VCDS Lite Long enough to do an adaption.

[@techclub8528]

Yeh maybe go for the full version its better value for money

[@BobSmith-mc7uq]

I know!! He didn't tell us that we had to have common sense either. Looks like you failed on that one! LOL

[@PompeyMatt17]

Very minor one mate.. Baud is pronounced "bored".... much like this comment :D

[@reinier660]

This is one of the many reasons you dont buy VAG...

[@SmAEsch0R]

chicken dance

[@yojomojo6262]

How much is the VCDS software and do you have to be in the trade to buy it?

[@techclub8528]

have a look at ross-tech.com, if you have any cable that is non standard then you need VCDS lite which costs around £80. otherwise you need to buy a genuine rosstech cable but all the information is on there site