Thank you so much i have same noise and now i know where is coming from👍
@ST-bk5uf5 жыл бұрын
Impressive ability you have, thank you for your video.
@CharlesSavvy3 жыл бұрын
Thank you for this video. My car is making a similar sound, and if I understand correctly, the solution is actually the center drive shaft bearing, not the transfer case, right?
@christiansprogoe49776 ай бұрын
Hi Bjarne, Firstly THANK YOU. Great vodeo and very helpfiul. Just to confirm please. Is it the longer rear drive shaft that you have in your lathe ? Can you confirm its the rear shaft or the front shaft pls? Thank you in advance. I have the exact same noise (But I have recently had the rear shaft center bearing replaced, so I may need to look at it again if you discovered a noisy rear center bearing. Thank you.
@mattsmithh24455 жыл бұрын
Bjarne, did you experience a vehicle shudder between 20-47 mph in addition to the noise? Very impressive mechanical work.
@dtechnic14698 ай бұрын
Hi I have a problem mytouareg r5. 2 3 shift not fix rpm going up. Whats is the problem
@motorsports56144 жыл бұрын
Great Job! Did you have an issue with the oil tube being loose towards the back of the case when you installed the tube? I would think it needs to be air tight. The one I have inserts but its feels loose
@Shane551138 жыл бұрын
your problem is most likely the propeller shaft from the transfer case to the rear diff, check the carrier bearing, if the rubber is torn replace the bearing or prop shaft, if you replace the bearing, the shaft is balanced so index it before separating the splines
@salemalonizan95467 жыл бұрын
dear sir, please help me.. i still have the problem after changing the chain, i still have problem shafting from gear 1 to 2. then gear 3 to 6 are smooth. please tell what else i have to buy to fix it. im desperately waiting for your answer. regards
@Shane551137 жыл бұрын
a shifting concern has nothing to do with the transfer case, check trans fluid level and then if found food replace the valve body for the transmission
@emmanuelgenis20465 жыл бұрын
Impossible de remonter la boite comme sur la video. Les 3 billes a ressort montées ici a la graisse ne peuvent pas passer dans la cloche sans les aider une par une. La solution consiste a monter le pignon avec les 2 syncros sur la cloche avant d’emmancher le carter long. Pour cela il faut enlever le joint spy coté arbre d’entree (forcement detruit) de la boite de transfert et retirer le circlips qui est derrière pour sortir l’arbre et tout ce qui va dessus.
@BoscaMarius5 жыл бұрын
Indeed helpful video, 💯 Beside this can you please 🙏specify in the title of the video or reply in this comment , what year and model of Touareg is this one ? what engine and which transmission type is, manual or automatic 🚗
@wekoigama34445 жыл бұрын
Where is the 2004 Touareg transfer case module located?
@elchappy34515 жыл бұрын
I have a 2004 v6 touareg can i use a 2005 transfer case?
@reese87466 жыл бұрын
Bjarne, what was the tiny square metal part you are holding at 8:10? Does it fall out unexpectedly during disassembly? I will be replacing just the chain this weekend and want to avoid running into trouble.
@berczigabor6 жыл бұрын
Isn't that the magnet that's supposed to collect the metal particles from the oil?
@4x4FordF6508 жыл бұрын
great video!
@np_39188 жыл бұрын
Hi I have a 2004 R5 2.5 tdi and I can only access low range. Any idea why ? I bought the vehicle in an auction and didn't know what problems it had.
@bjarnethem8 жыл бұрын
You say it is stuck I low range! Maybe it is the stepper motor. The electric motor that switching between high-low-diff lock. Located on the transfer case. The first models had a bad quality stepper motor. Or the electric connation’s to it. Switch-connectors-wire-controlbox etc. The stepper motor is easy to replace. Have you run at fault scan? Maybe it gives an idea.
@np_39188 жыл бұрын
I got a friend to run vag com and a list of faults popped up. 1. Camshaft position sensor 2.control module for diff lock 3.abs wheel sensor - each wheel sensor sent a fault code 4. Control module for transfer case - would this be the stepper motor that needs replacing? 5.supply voltage terminal 6. Engine speed sensor
@bjarnethem8 жыл бұрын
I am sorry that I can’t say what the precise problem is but it seems you should start look at the Control module for transfer case and diff lock
@redzeroiceman92975 жыл бұрын
drive shaft bearing mostly well be the one or rarlely front diff
@raulnieblas7 жыл бұрын
What was your problem that made you repair the TC?
@stevenmudenda5 жыл бұрын
My car 2004 treg 2.5 tdi has a knocking sound when turning, suspected it was CVs, changed them but no change. High-Low -Diff Lock also brinks sometimes. My mech suspects a transfer case problem. He suggests changing. Thats a hell lot of work and expensive. Before i go there, maybe the problem is low lying, could it be a stepper motor? or transfer case oil needs changing? please help.
@ElPrimo-tq1bb3 жыл бұрын
Did you ever found the problem, I'm having that problem to
@kinderutz7 жыл бұрын
So you took the TC out and apart for nothing? It was the center support bearing all this time? Yikes!
@simonmewett47395 жыл бұрын
What oil would be in the transfer case pls ? 2004 2.5 R5 6 speed Automatic Thanks
@a_a_11994 жыл бұрын
genuine VW transfer box oil, part number: G055515A2
@lorifoy46257 жыл бұрын
trying to get transfer case off my 08 Tourareg but 1 bolt at the very top is almost impossible to get out. any advice on how to remove it?
@bjarnethem7 жыл бұрын
Lower the gearbox end as much as possible. look out for what happens in the engine bay when you lower it! Use socket wrench and as many extension pieces you need and maybe an cardan joint. Or what ever it is called in english.
@salemalonizan95468 жыл бұрын
Thanks for the video Please ... Can you tell me what is the chain part number ? I'm going to buy new one ? Thanks again
@bjarnethem8 жыл бұрын
Sorry. I can't. I have no idea.
@Shane551138 жыл бұрын
google search NP235, that is the chain the Touareg, Q7 and Cayenne use in the transfer cases
@salemalonizan95468 жыл бұрын
dear sir can i have your whatsapp number to communicate i still have same troubles in the transfer case box and i believe you know the spare parts names and codes to make order regards
@bennyb86805 жыл бұрын
I hava 2006 Touareg when i get to 40 45 mph it starts to shake. Dunno whats wrong @bjarnethem
@omen19698 жыл бұрын
What is the number for the hub nut "output flange"?
@bjarnethem8 жыл бұрын
+Osvaldo Mendez Socket is 36 mm. 12 point. You will need a long one. Or like I did, cut it on the middle and weld in a couple of centimeters of a pipe.
@omen19698 жыл бұрын
muchas gracias (thanks) Bjarne Them, where do you from?
@AveGuy16 жыл бұрын
This guy is tough. I would have just taken the car to the mechanic.
@redzeroiceman92975 жыл бұрын
get new tranfer case servo motor as well the rod get bent
@СерикБерик-ц2ч4 жыл бұрын
Чёт я нихера не понял что этот дядя Вася в своём гараже ковырял? И заменил ли он цепь или оставил старую остается только гадать.
@Chuk_Norris3 жыл бұрын
Все разобрал, посмотрел все в порядке, собрал. Потом выяснил что шумел подвесной подшипник, его заменил. Денег за ремонт раздатки естественно взял
@chrisland1696 жыл бұрын
don''t buy this one he is running the truck without propeller shaft and you can listen to the high pitch noise !!
@bjarnethem6 жыл бұрын
you have no clue what your are talking about
@rajm95116 жыл бұрын
Are you on meth? you are really clueless. so sad.....