For specs and purchases of Longer LK4X, click the following links: s.zbanx.com/r/87XkMHbc9ev0 Longer LK4 Pro: s.zbanx.com/r/bC6oAPEOeWdr Longer Lk5 Pro: s.zbanx.com/r/KLbHR4rhtAKN Cube 2: s.zbanx.com/r/uAe3Abb0XW7D Have you tried Longer Laser Engraver? A perfect companion for your 3D Printer: 10W Laser Module: s.zbanx.com/r/9YrVL9XTZYM3 Longer ray 5 with 5W module: s.zbanx.com/r/fP8oGK09rxvS Longer ray 5 with 10W module: s.zbanx.com/r/OeP4xTeKID3N
@Beecher_Dikov6 ай бұрын
I started using a bit of glue stiick and my warping issue stopped.
@simonecinarelli4240Ай бұрын
I tried too... The plate litterally bent
@kitcarlson6033 Жыл бұрын
It looks like retaction settings need adjustments. Nozzle seems to leak at layer change.
@stopsnstuff50968 ай бұрын
Thanks!
@Darkhell878 ай бұрын
I don't understand how that helps. If temp changing is the issue it warping at this wall is going to ruin the print also.
@MiddleRoomWorkshop8 ай бұрын
Hi, thank you for your comment. Your comment makes sense, but the closed wall creates a volume of hot hair that keeps the temperature inside it a bit higher than the surroundings, as a result, the wall itself is less likely to detach and subsequently also the prints gain a positive effect from this. This is a quick trick that can help reduce warping, but is not a definitive solution and the are other factors/parameters into play that should be addressed. For example, bed cohesion is the first and most important factor to correct. This depends on the z-offset, the type of bed, first layer temperature, and height. For example, another way to increase cohesion is the use of a brim, I use large brims when I have thin details with small contact points to the bed. If the print does not detach before is completed the warping if any is drastically reduced. I hope it helps
@Darkhell878 ай бұрын
@@MiddleRoomWorkshop I understand all that. But if the outer wall warps blocking that air wouldn't it have the same odds of failing and causing the rest to fail.
@MiddleRoomWorkshop8 ай бұрын
Yes, if the wall fails than the print may also fail.
@jesus26212 ай бұрын
@@MiddleRoomWorkshop so it does not work
@monsterstorm78 Жыл бұрын
Hey what printer is this 🤔
@MiddleRoomWorkshop Жыл бұрын
Hi, @monsterstorm78; thank you for your comment. The machine is the Longer LK4X which I reviewed here: kzbin.info/www/bejne/mneloWmVgNSMibs For some offer link have a look below: s.zbanx.com/r/87XkMHbc9ev0 Longer LK4 Pro: s.zbanx.com/r/bC6oAPEOeWdr Longer Lk5 Pro: s.zbanx.com/r/KLbHR4rhtAKN Cube 2: s.zbanx.com/r/uAe3Abb0XW7D I hope it helps Ciao
@mohistschool1003 Жыл бұрын
You need the QIDI Max3, It have the heating chamber, so warpless printing.
@MiddleRoomWorkshop Жыл бұрын
Hi, @mohistschool1003; thank you for your comment. I agree that it is quite an impressive machine but also out of reach for many. A fully enclosed machine generally produces better prints thanks to thermal environment control. Ciao
@otashikitsune146011 ай бұрын
Sorry for this, but it's a useless advice. Still warps a lot and just a total waste of material. The filament still blend because of the low temperature. The only solution is to cover the whole printer to maintain a stable temperature, so the plastic doesn't bend too much. Doesn't matter if you put a shield, cuz the lower temperature already affect the first layers, and at the time the shield is higher, the damage is already done.
@jozo9212 Жыл бұрын
I can already see all of the bltouch users buying enclosures or doing this stuff because their z offset is too high
@MiddleRoomWorkshop Жыл бұрын
Hi, @jozo9212; thank you for your comment. That's a good point; definitely, something I should have mentioned. This is now a permanent solution but a quick one. Yet, with te z-offset right, you can still face warping problems with corners detaching, like in my case. There are several solutions for that, both from a design standpoint, like avoiding corners and adding fillets, from a slicing standpoint, using extra brim or anti-warp tabs (available in cura), playing with temperature, and hardware standpoint, like changing the bed type or replacing the bed if worn out. Ciao
@Kysen107 ай бұрын
2:19 still warped (left model).
@MacHaradze6 ай бұрын
As it should. it was the example of warped model dude