WCFab 3.5 Inch Passenger Side Intercooler Pipe Install. 2017-2019 2500/3500 L5P Duramax!!

[@rk13069]

This is one of the most realistic install videos I have seen in a while. Thanks for honest content and comments on what to watch out for.

[@linksgarage1985]

Hell yea! That’s why I wanted to make them. I always hated video that cut out the crappy parts! Hope this helps!

[@waynejohnson3388]

Nice job! I just bought a 2013 chevy silverado 2500HD 6.6L LML Duramax with 144,000 miles on it. It's completely stock. 1st thing, Air Dog lift pump, and then all the hot and cold piping is getting replaced. Your video gives my the extra insight to tackle the job my self. This is my 1st diesel and I'm excited to learn as l go. By the way. Awesome shop, love the American flags!!

[@victoroliveira3256]

I have the same pipe, I only had it blow out on the Intercooler connection twice when I really gave it the beans, than I found that the groove cut where the clip snaps into was not cut deep enough so I took a file and shaved her a little longer, it wasn’t just me it happened in a jw Montoya video on his friends L5P, I didn’t contact wcfab cause since I fixed it it’s been great, I also boost checked it was fine through and through, great video man I hope you have better luck than me, mind you I had one of the first they made, keep these videos coming there the best on KZbin, also all my other wcfab stuff has never gav3 any issues so no discouraging anyone.

[@linksgarage1985]

Hell yea! Thanks man. I appreciate that! This video was over 40 separate clips edited together. It takes a lot of work to put it all together. Glad someone is getting some use out of it! I hope I’ll keep you posted on the status after I drive it.

[@jonathantrentham3579]

Thank you for the videos!! Im in the process of changing out all my pipes to WCFab and found your videos helpful!!

[@linksgarage1985]

Awesome! Thanks for watching! Consider subscribing for more L5P content to come! I appreciate it!

[@drewmorey6070]

As I was searching for WCfab colors I found your channel. The install videos are awesome and show exactly where and what’s needed! Glad I found your channel and sub’d keep it up Scott

[@linksgarage1985]

Hell yea Drew! Thanks for watching. That’s why I made the channel. To help others. I struggled to find the content for myself, so I decided to film it for everyone else like me! I appreciate the sub! Much more to come. And lots of older vids to watch! Thanks again!

[@drewmorey6070]

@@linksgarage1985 I’m going though all your vids now. I have a 17 GMC 2500. I’ve done a good amount of work to it but haven’t decided on a color so the WCfab stuff is my last to do until they make some manifolds. I’ll be checking all the content and look forward to the updates!

[@linksgarage1985]

@@drewmorey6070 - if I can ever help let me know. You can always hit me up on Instagram @scottlink_l5p. Thanks again. Best of luck!

[@drewmorey6070]

@@linksgarage1985 thanks found ya. I’m sure I’ll have to hit you up at some point but until I’ll be following your posts!

[@linksgarage1985]

No problem sir. Glad to help always!

[@IronheadGarage]

That's a sweet tool to get those Christmas trees off they always brake so easy

[@linksgarage1985]

Thanks man. I’ve got like 10 of them. lol. Different lengths etc. pretty handy. Thanks for watching. I appreciate it!

[@astiles21]

I just got mine on today. As for the bottom clip the written instructions say to one hole is cut smaller. I ended up rotating my clip 30 degrees off from what you show to get it to clip on.

[@linksgarage1985]

Hell yea!

[@cavtj1]

Good job Scott! Let me know if all the new pipes help performance/mileage and such. Thanks for posting, I learned something!

[@linksgarage1985]

Thank you! That’s the goal. To document everything and help some folks along the way! I appreciate you watching as always!

[@linksgarage1985]

And I sure will let you know how everything goes!

[@victoroliveira3256]

Woo hoo another video let me get my popcorn.

[@linksgarage1985]

More to come!!!!! Thanks for tuning in as always! I appreciate it!

[@xlandscaper]

Good install vid. It’s a shame such a pretty part gets all covered up and it’s hard to see with everything all buttoned up. Looks like you got plenty of other purple goodies to install tho🤘🤘🤘👍👍👍

[@linksgarage1985]

Yep. Just like the turbo horn. Almost invisible. It’s ok. More goodies to come! Ha. Thanks for watching man!

[@dougstoltz1320]

just curious as to which of the brackets you took off, stay off. Couldnt tell from the end. Thanks and super video.

[@Nathang2233]

Installed one on my buddies truck the fitment was horrible pipe didn’t line up it was about impossible to get the clamp on so it didn’t blow off used a bunch of hairspray too

[@tacticalbreadman7409]

YOUR KILLING ME LOL.........................NICE Great filming. Up pipes?

[@linksgarage1985]

More to come sir! Thanks for watching. I appreciate it! Several more goodies coming soon!

[@angelovino2646]

Hey man I have a question for you. So I’m in the same boat as you were with the pipe blowing off on the intercooler side. I have pushed as hard as I can on that pipe and it seems to be seated all the way in bc I felt the pipe go into the 2 O rings. But then when I step on it, I hear the whoosh sound and then it’s loose again. Does the pipe have to go over that little little on the intercooler? I figured since the pipe sits all the way up against that small plastic lip, it was all the way on but I seem to have it come off under pressure. Weird part is that clip still is in the right place even tho it’s loose 😂

[@allenpardon8211]

Great video, I have a 2019 also and I noticed that when you pulled the old pipe off and the end with the clips from hell on it, it looked like there was residual oil in the pipe. If was oil, where does that come from? Thanks

[@kylechew7127]

Most likely your PCV connected to your turbo horn . The PCV can release oil vapors that can accumulate over time inside your intercooler pipes . That’s best case , worst case you have a failing gasket on your turbo . More thank likely if that was the case it would be shitting oil out everywhere.

[@kylechew7127]

Order a PCV re route kit and while your at it install an oil fill re route.

[@alan2256al]

What kind of lubricant did you use on the o rings

[@linksgarage1985]

Safe for o rings! shop.advanceautoparts.com/p/lube-gard-assemblee-goo-green-size-1-pound-19250/11302001-p?c3ch=PLA&c3nid=11302001-P&adtype=pla&product_channel=online&store_code=&gclid=CjwKCAjwy7CKBhBMEiwA0Eb7asYYFOlAqcgSu8AoToNeOyKGkWx4jdCiWsB2MZKzqMQQldaL_GtnfhoCCOcQAvD_BwE&gclsrc=aw.ds

[@alan2256al]

@@linksgarage1985 thanks for the info

[@linksgarage1985]

@@alan2256al no problem! Thanks for watching!

[@brendazamudio1979]

Is this one better then the one banks came out with

[@linksgarage1985]

🤷🏻‍♂️no idea. Both big hollow tubes. Prob very similar.

[@ma93256]

Do you need to tune for all these wcfab upgrades you’re doing? Do you plan on deleting?

[@linksgarage1985]

No you do not! No tuning required. Thanks for watching I appreciate it!!!!

[@galentine166663238]

How bad was that bottom clip to get back on ?

[@linksgarage1985]

Just getting the damn pipe on was more or an issue. Don’t get me wrong. The clip sucks!!!!!!!! I might even make a follow up vid on it. It’s a real bitch. Thanks for watching. I appreciate it. Consider subbing for more L5P content! Coming soon!

[@alan2256al]

I installed the 3.5 inch cold passenger side pipe.. what a bitch to deal with that clip.. even with the strap.. but I got it and hope I never have to touch it again.. but without your video.. I would have been lost as last years Easter eggs

[@linksgarage1985]

Awesome!!! Yep. I’ve fought with that one. But it’s been holding strong for about a year now. Glad to help Alan. That’s why I made the videos! 💪🏼

[@alan2256al]

@@linksgarage1985 gonna try the drivers side tomorrow… it seems like it may be easier.. I got the illusion blueberry color.. except my cold air intake is HSP ..

[@linksgarage1985]

@@alan2256al HSP make good stuff also. The driver side is wayyyyyyy easier. Leave the bubble wrap on it until it’s installed so you don’t scratch it!

[@alan2256al]

@@linksgarage1985 I installed the drivers side.. piece of cake.. feel like I did something wrong it was so easy.. but now I waiting on the 5 inch bank’s exhaust

[@linksgarage1985]

@@alan2256al I told you! Glad you knocked it out. And I ran the Banks intake set up. It’s great. You’ll enjoy it.

[@hatchetwarrior1240]

2020 oil cooler upgrade

[@linksgarage1985]

Yep. Those thinks are heavy duty. I believe that’s why the tow rating increased for 2020!

[@hatchetwarrior1240]

that and maybe the ten speed

[@linksgarage1985]

@@hatchetwarrior1240 yep. You are correct! Thanks for watching and commenting. I appreciate it!