2 techniques that professional welders use to weld square tube in vertical position.

[@kevinkirk4285]

Vertical up position is the most difficult to master but has the best penetration and strength versus vertical down method. The vertical down weld @ 2:24 is perfect. And the vertical up @4:01? Well done Sir! Well done indeed, I say!

[@phillipstownsend1176]

If I weld like this, I would be fired. slag inclusion central

[@catabaticanabatic3800]

Sir,yes Sir! Has he been knighted by the King?

[@juancarlosrivera7359]

He visto muchos videos sobre soldadura al arco, pero éste es el primero del cual he aprendido cosas prácticas. Los felicito y muchas gracias.

[@aniswaili4777]

Je suis un homme de plus en plus mince et je cherche un emploi

[@JesusTorres-xz5jt]

En realidad no hay mucho que aprender de este video....cada país o región tiene ciertos parámetros o reglamentos en cuanto a soldadura se refiere,lo que es aceptable para unos quizá no lo sea para otros....además también cada persona es distinta,lo que funciona para un soldador quizá no funcione para otro o no le sea permitido hacer en su trabajo por reglas y procedimientos.

[@enjo9881]

It’s HILARIOUS when ALL THE “EXPERTS” come to the comment section to complain and moan yet they’re on a how to weld video comment section. Let that sink in.

[@juancarlosgiron7053]

Maestro: 1) Que tipo de electrodo usaste??? 2) Que Amperaje usaste??? 3) Que Espesor del caño que soldaste??? 4) Que Marca de soldadora usaste??? Gracias

[@jas007000000]

Parece que es 6013 - 1/8 , con 90A

[@juandomingocisterna4766]

Si todo bien! Pero esplica que es lo que usaste, electrodos y amperaje y tadas esas cosas! 🤦🤦🤦🤦

[@АлександрСерик-е8р]

От души молодец, мне есть куда стремиться. С наступающим здоровья и всех благ.

[@Sam-gq3ku]

Muy bueno el instructivo gracias!!! El trabajo quedo espectacular lo felicito y gracias!!! Que tipo de electrodo usaste 7015?? Gracias desde argentina un abrazo

[@carlosvenegas2186]

Minuto 0:24.

[@shkurmander]

perfect! but that is 3mm steel, and its more easyer, than on a 1.5-2mm. Can you show how to make the same on 1.5mm steel profile?

[@masterQ20]

excellent tips my dear friend 👍 ✨ ✨ ✨

[@arseniovera672]

Espectacular amigo el trabajo esta de maravillas. Esta súper. Es todo de un profesional. .saludos desde lo lejos .🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷

[@diegofernandocoronadocerqu5766]

Con ese calibre es fácil el cordón. Porque no muestra como se suelda en calibre 20

[@cesaralbertocadenahernande8222]

Pregunta: Que amperaje utilizas para soldar ese tipo de metal? Necesito soldar unos polines "encuatados" a una placa de metal en el piso. No quiero poner ángulos de 90º, si no que quiero soldar el polín directo a la placa, pero me falla al momento de decidir el amperaje!

[@christownsend2399]

In all my time as a qualified ticketed welder 35 yrs plus I've never seen a vertical up run in spot welds, it would be ok in a farmers field on a gate maybe but that's about it. Great video though

[@christownsend2399]

@Way Outthere Sorry mate didn’t mean to offend you, I’m also sorry for spending the first 6 yrs of my working life doing an apprenticeship in the boiler making and heavy structural steel industry doing gas and oil pipe and skid work on sight, you are obviously suffering from some form of insecurity syndrome. You know how tradesmen recognise bullshit artists like your self? You spew insults knowing full well I could never challenge you, so I’ll tell you what mate, just climb back in the cesspit from which you crawled. I never once insulted or challenged the person who took the time to make these videos I just pointed out that I’d never seen done what he did, plus I complimented on the videos. GFY.

[@christownsend2399]

@@intiaboats Cheers mate 👍🏻

[@jb243wp]

​@wayoutthere8637 You correct there buddy.. I've heard this claim time and time again- "I've been a welder for 35yrs" 💩... What they forget is that there is a difference between a ticketed qualified welder and a qualified ticketed welder 👍

[@carlosc.c9686]

I've been welding for 78 years and I can say I've never seen this perfect technique anywhere.

[@AntonioNobre-n6u]

Ich freue mich immer wieder solche Videos anzuschauen, wo die Leute richtig Spaß an der Arbeit haben und wissen auch was sie posten. LG, aus Portugal

[@jeronimovallejostorres]

Yo soy un desastre soldando todavía, pero al ver tus videos me motiva más para seguir practicando. Si existe un Dios soldador seguramente eres su primogénito. Excelente. Saludos

[@ricardoherrera8407]

excelente video, un saludo desde Mendoza Argentina

[@F1236100]

Какими электродами такие чудеса? неужто волшебной палочкой дерижировал!

[@АлексейГрачёв-й6р]

Очевидно, рутиловыми. Просто зажигаются, неплохо варят, но шлака много. Профи же варят основными типа УОНИ и там сварка с отрывом затруднена.

[@stickstone6885]

Perfectly acceptable technique for thin square tubing light welding work like gates, doors etc. This is not building a cargo ship or nuclear plant.

[@bonifaciogarcia3987]

Ilang ampirahe po ang tama gamitin para sa tubular welding po?

[@carmelpule8493]

I concluded that you are a good welder by the selected music and the accompaniment of the sounds like YAAAAHUUUUU! While the 6013, the diameter and the amperage are important, it is just as important to dwell for a longer time where there is more meat in the workpiece. .In the vertical square section there was the bulk material of the CORNER while the horizontal square section there was the flimsy EDGE. so one needed to dwell more on the corner rather than the edge. EXCELLENT videos and again , I like the music and the occasional YAAAAHUUUU. and of course the WOW! Well done.

[@jubileedludlu7431]

All the best guys but the amp and the material should be stated also

[@ananghadi1528]

Las nya merk apa? Ukuran kawat las berapa ? Besi yg di las tebalnya berapa? Utk mendapat hasil yg bagus

[@ДаниилПаджериков]

Все ништяг, а можно узнать спецификацию всего? Толщина труб? Электроды какие и толщина? Настройки сварочного аппарата?

[@luckybootleggers1699]

Des soudures de ce niveau cela devient de l'art !!! Bravo à vous 👏👏👏

[@hectorr814]

EXCELENTE VIDEO¡¡... SALUDOS DESDE MEXICO¡¡

[@johnmcprom2514]

สุดยอดเลยครับอาจารย์

[@vi2win]

เชื่อมสวยมากครับ พี่น่าจะพูดอธิบายด้วยนะครับ

[@alexandersuarez1067]

Saludos desde Venezuela!!! Excelente trabajo amigo Alexander Suárez

[@АртурГришин-щ4ч]

я рпр

[@enriqueoses4574]

Buena técnica......¿le quedará igual en un perfil de espesor menor, 2mm?🤔

[@whatthedeuce091]

This is not how pro welders do vertical structural welds.

[@b.p.rwebber8098]

I don't weld for a living but I wouldn't use that technique on anything I weld. Thats why electrode sizes are as thin as 1.6mm so thin steel can be welded with lower amps and decent beads that will be strong. Tacks are fort holding steel together before a proper solid weld can be put down.

[@gyorgyjanoswallinger5404]

Szép és tökéletes varratok!

[@felixTifoona-ud3vy]

Mantap n teruslah berkreatif

[@BENGLASBERKAHCHANNEL]

Yah huu....teknik pengelasan yang handal hasil baik 👍👍

[@gonzalo7130]

Excelente!!!👏👏👏 Saludos desde Argentina

[@джонсмит-вессон]

Супер 👍, мечтаю такого уровня сварки. Я стараюсь😊

[@paillart527]

Whooaa what good soldering. Congrats and thanks sharing your skills.

[@ZonunLibra]

Nice work nice weld finish

[@VwMikc]

Great video,thanks.👍

[@muhandy491]

YES....good job Bro...! Succes.

[@igorivanov7232]

the welder must mention other variables like the type of welding rod used, the thickness of the tubing or the amperage rating where the machine is set at.

[@JoaoFaria-hj5hk]

Bom de mais cara

[@olivierleger2530]

it says: E6013 2.5mm at 80 amp at the begining of the first weld

[@JesusTorres-xz5jt]

Try smaller rod and lower amp setting on your vertical uphill to see if you can run a continuous bead ...you might get slag trap in there and weld won't be solid.

[@zenobiahaku4087]

He used 6013, not 6011 or 7018, this „stop-weld” is a good technique with it, when you go uphill. It is useful even with 7014 electrode. 6013 and 7014 are not fast freezing type electrodes, you cannot weld with them on uphill continuously. This is not an easy technique, it takes a lot of time to master it, but can be useful, when you only have 6013 in your pocket...

[@texaswelder3745]

@@zenobiahaku4087 I can't think of any process where you could weld like this and pass any kind of test. It may work somewhere other than the U.S., but you won't have a job for long doing that here. There are actually standards you have to meet with your work, for safety reasons, for one thing. Edit: also, the "1" in 7018, 6010, etc, tells you that you can actually do a continuous bead uphill. If you were using, say, a 7024 ("jet rods"), that is a flat or horizontal only rod. Either way, stopping and starting like that is a no no.

[@zenobiahaku4087]

@@texaswelder3745 Here, in Hungary, this is a mandatory technique in a welding exam. You need to do two welds, one fillet weld, overhead position on 60mm diameter, 4mm thick pipe, and 5mm plate. Your second weld is a vertical butt weld, on 4mm plates uphill, 300mm long (plus the start and finish tabs). You have only 6013 rods, with the diameter of 2,5mm...the fillet weld is not a big deal, but the second one is a nightmare...skip-n-weld, and avoid slag inclusions, excessive root penetration, and make decent crown width and height...

[@joshkarena3058]

I agree, we were taught to weld a constant continuous flow to avoid slag entry.

[@JesusTorres-xz5jt]

@@zenobiahaku4087.... 6013 stick rod it's all there is available to weld in your country???

[@JoseSanchez-ko6fl]

Grasias por enseñar como se solda saludos desde California

[@ichirosuzuki9918]

上から順に溶接するのと、下からするのと、仕上がりが違うようですね。 どちらが正解なのですか？

[@donkuwik3390]

Thank You for making all your videos. From Detroit, Michigan, U.S.A.

[@weld_dx]

🙏🙏🙏

[@ВалерийТеликанов-о8в]

Вы - лучший на Ютюбе 😀👍✊😇

[@sangthohan]

Video rất hữu ích,tuyệt vời you🥰

[@livedupro]

Nice good ticer

[@TheRockeye007]

LOVE THE TUNES!

[@aljenetalisic]

Wow nice job dol

[@АлександрЧех-в5щ]

Варианты разные.но швы можно делать и лучше .а всего то нужно подобрать электрод и силу тока .а в общем видео хорошее автору жму руку 💪👍🤝

[@alickkk]

Да, без камеры можно и лучше ...👍

[@norman7179]

👍👍 My weld would have been full of slag inclusions. Which rod was used ?

[@texaswelder3745]

Do that anywhere I've ever been and expect to be rolling up your leads and being escorted off the property.

[@MrKentaroMotoPI]

Those welds are fine. You have no material process knowledge. Don't be such an ass, Texass.

[@texaswelder3745]

@@MrKentaroMotoPI Maybe not, but I've been burning rods in the oil field, power plants, rock quarries, and a few other places for 31 years, and ass or not, you try to weld like that anywhere I've mentioned and you'll be gone before your first paycheck. Trying to save a young pup the trouble if this is where he's learning to weld.

[@yusufswartz4958]

What's the best method ,if you can explain to me please

[@mozdy7457]

@@yusufswartz4958 Your weld should be a continuous bead, chaining 20 tack welds on top of each other is a great way to make a shitty weld

[@robertg8930]

​@mozdy7457 thank you!

[@vishnuchandrabahadur9398]

Wow very nice 👍

[@bcpnando]

Que solda perfeita!!! Show. Essa chapa é 18?

[@5mblog995]

Ok boss gayahin ko nga

[@johnfavela3817]

I have a Hobart stick welder what ampridge do I set it at for sch 40 steel pipe or square tube. Like the one your welding here .

[@pirateph4799]

Very nice.. perfect😊

[@나-w3e1m]

멋지네요 Very nice wellding

[@weld_dx]

🥰🥰

[@jflorentbivihou]

waaouu très simple et efficace ! merci je suis abonné à votre chaine , j'espere que vous aller faire d' autres video merci super

[@BishnuGurung-i9t]

very good job sir

[@Савва-г5в]

👍Яхуу я такой мастерской сварки ещё не видел

[@claudiomoraes6482]

BELA SOLDA , TRABALHO ADEQUADO OTIMO PROFISSIONAL PARABÉNS

[@maalvi1]

Озвучка классно сделана.

[@SpottedEagleOwls]

very good

[@khalikassayuti2192]

adakah rode saiz 2.6mm boleh digunakan untuk besi hollow yang bersaiz 1.0mm?

[@АлаТоо-ц2ф]

Очень шикарно👍👍👍👍👍

[@az7288]

ตอนเชื่อมลงถ้าใช้E7013จะรั่วมั้ยครับ

[@weld_dx]

หมายถึง 6013รีเปล่าครับ ถ้าเชื่อมดีไม่รั่วครับ

[@ابوهادي-ع4ت]

تعلمنا منك الكثير شكرا لكWe learned a lot from you, thank you

[@rodolfod.9270]

Waooo!!!! Yahoo!!! Exelente trabajo. Desde Bolivia tienes un seguidor.

[@Batchi15]

Wow good job

[@A_dul02]

ช่องคนไทยป่าวครับ

[@marcellebaudry5786]

super bravo

[@nurahmanudinlove1494]

Sangat menakjubkan ...

[@Злой-х9п]

Приятно глазу.

[@jineen123]

Vertical weld always start from the top down for cleaner weld. it also needs to be spiral not zig zag. I find this method works perfectly.

[@몸살난지구]

옆으로 용접하는것좀 보여주세요. 위보기 용접도 보고 싶습니다.

[@clarocanartworks7358]

What is the Set up Ampare on welding Machine?if the size of welding electrode is 2.5 mm.?

[@weld_dx]

I use 75-85 amp. For 2.5 mm. Electorde.

[@alickkk]

5:38 - ни разу не видел такого красивого шва при сварке с отрывом!

[@Dantocta]

Quá đỉnh cao. OK lắm!

[@GoshaF-e4e]

Красивая работа👍

[@Омногомпонемногу-н8э]

Я бы не сказал, что прям супер шов. Я подобные швы видел в колхозных мастерских. Один сварщик на моих глазах электродом 4 заварил консервную банку.

[@Tokitux]

покажи супер шов, а?

[@djreyo1712]

Nice work.Cape Town

[@SkyviewShine-ny8pq]

Makasih ilmunya mas.sangat bermanfaat buat saya

[@buonlangee.2815]

Wow good

[@aresthamzah9795]

apakah dri indonesia?

[@franckcasula9516]

Super grazie

[@eustrebertoramirezlorenzo8936]

Excelente trabajo, lastima que solo pueda darte un lik estoy suscrito saludos desde acapulco México

[@bernardoandreslopezisaac7358]

Me gusta mucho estos videos

[@STREETWELDING]

Mantap semangat berkarya

[@kloktr5327]

Perfect 👍

[@notmasir_7150]

ใช้ไฟเท่าไหร่ครับพี่

[@moukamiel8134]

Super la sodura.

[@sniperecek-ecek6801]

Best 👍👍

[@martinbobfrank]

I'm not a professional welder, or even a fitter but I used to weld non-essential gear at work. I was always told that the slag on a good weld should come off itself, which it did and I'd feel gutted if I had to chip away the flux at the end; it was like someone saying 'that was shit.'

[@frankkante7850]

Lovely

[@johnross3752]

You'r fired .... But I like the way you burned through the porosity

[@b.p.rwebber8098]

Cut and etch would be interesting.

[@gustavomartinez5620]

Que electrodo usar y que amparaje es idea??

[@eduardodelacruz8527]

buena explicacion

[@alaintartempion6214]

Il est primordial d'avoir un bon réglage de l'intensité!

[@miguelmedina8149]

Noches maestro, de que calibre es el tubo cuadrado???? Gracias

[@unkindnoob6680]

That downhill is the correct way.Not that Tack stacking cuz that causes inclusions .If you are gonna be tack stacking,just clean after every tack.

[@ricardomolina7431]

Desde Chile, gracias por la instrucción.