What is the difference between Pipe and Tube ट्यूब और पाइप में क्या अंतर है

[@sureshkumar-gi2mq]

U have gained very good knowledge in technical… keep it up

[@superfaststudyexperiment]

Thankyou

[@vishalprajapati7706]

Apne ghr me jo cooking gas aata h yellow painted material me,wo tubes hoti h ya pipe? N wo kis metal se bnta h?

[@Srk7028]

good video.......

[@RakeshYadav-ow1ne]

Nice video sir ji ❤️❤️🙏🙏

[@sachidanandtrivedi5270]

Very good 👍

[@superfaststudyexperiment]

Thanx for watching brother

[@RajendraPrasad-eu6le]

Very nice

[@superfaststudyexperiment]

Thanx for watching

[@anandpandey9134]

Nice

[@superfaststudyexperiment]

Thanx for watching pandey ji

[@Fab2Mc]

Super 👍👍

[@superfaststudyexperiment]

Thanx

[@RakeshYadav-ow1ne]

Thanks sir ji ❤️❤️🙏🙏

[@superfaststudyexperiment]

Thnax for watching please subscribe brother 🙏🙏🙏

[@mjrajgor3621]

👍

[@NaturalBodybuilding]

Mast topic bhai

[@superfaststudyexperiment]

Thanx bhai

[@azimkhan6154]

Please make video on tube manufacturing process and important question according to interview point of view.

[@superfaststudyexperiment]

Ok y

[@AmarjeetJoshi21]

Pipe drawing or tube drawing is the metal forming process used for manufacturing tubes,rods and pipes. Whereas wires are manufactured by using extrusion process.

[@SuhailKhan-fh9re]

Sir ye btaeye ki agar pipe banding karna hai to cr sheet ka pipe shi rhega ya he sheet ka pipe shi rhega

[@gyan2328]

Thank you 🙏🙏

[@superfaststudyexperiment]

Thanx for watching please subscribe there are number of such type of videos in this channel.

[@akashchatterjee7762]

Sir ak baat bataye ki feed tube ko feed pipe kiyu nhi bola jata? Ya cb pipe ko cb tube?in dri??

[@bishwanandkumar584]

Sir tube mill ki upar vidio banaye and roll size

[@mjrajgor3621]

👌👌👌🙏

[@tejasvisingh8962]

Sir mere liye v job btaiye na mai sponge iron m shift incharge hu

[@motivationalvideo8763]

Sir pipe bhi square cross section ka hota he

[@RajendraPrasad-eu6le]

4 hol ka planch farmula

[@anandpandey9134]

Sir steel plant mechanical engineer ka va vacancey btaye

[@superfaststudyexperiment]

Ok brother apna what's up number send kariye

[@waseemafridi796]

@@superfaststudyexperiment bhai ap apna WhatsApp send krdo my Pakistan sy hu kuch information lynyy ty ap sy

[@tejasvisingh8962]

@@superfaststudyexperiment sir mere liye v job btaiye na mech engg m Sponge iron m shift incharge hu surg dist Me

[@technoeditor7013]

@@tejasvisingh8962 bhai me bhi sponge iron jagdalpur me hu mech department me

[@anandpandey9134]

Sir mai what's up number send kr deya hu

[@Ajay_-pl8yj]

Pipe ka OD fix hota hai or tube kaID fixed hota hai

[@superfaststudyexperiment]

Pipes are typically measured by their inside diameter (ID) and their schedule, which refers to the wall thickness. The schedule determines how thick the walls are and affects the strength and pressure rating of the pipe. For example, a 2-inch pipe with a Schedule 40 will have a thicker wall than a Schedule 20 pipe of the same diameter. Tubes, on the other hand, are measured by their outside diameter (OD), and they have standard ranges of wall thicknesses, typically expressed in terms of gauges or as a specific measurement. For instance, a 1-inch tube with a 0.065-inch wall thickness is common for structural purposes, while a 1-inch tube with a thicker wall may be used for pressure applications.

[@Ajay_-pl8yj]

@@superfaststudyexperiment bhai tthicknes jab bhi badta hai to pipe ka id kam hota hai od nahi odi fixed rahata hai od kabhi kam ya jyada nahi hota hai pipe ka

[@kewalrajsinghvi6764]

मोप वाइपर के पाइपके बारे मेजानकारी हो तो बताये

[@RakeshYadav-ow1ne]

Sir please provide video type of alignment and type of Coupling.

[@superfaststudyexperiment]

Thanx for watching brother I will try to make video

[@OFFICIAL_AYUSHOP]

NB, NPS ,NB is not same as ID brother. .

[@fitterisgreat6928]

Hindi me batyo

[@superfaststudyexperiment]

हिंदी मे ही है वीडियो भाई जी आप देखिए तो सही पहले।

[@fitterisgreat6928]

Ha hindi me hi sab sabd hindi me nhi sir jj

[@Ajay_-pl8yj]

Tum thoda or pad lo babu

[@superfaststudyexperiment]

Babua lo tum padh lo acche se likh k bhej de raha hu aur agar samajh me na aye to Google bhi kar Lena theek hai naa Pipes are typically measured by their inside diameter (ID) and their schedule, which refers to the wall thickness. The schedule determines how thick the walls are and affects the strength and pressure rating of the pipe. For example, a 2-inch pipe with a Schedule 40 will have a thicker wall than a Schedule 20 pipe of the same diameter. Tubes, on the other hand, are measured by their outside diameter (OD), and they have standard ranges of wall thicknesses, typically expressed in terms of gauges or as a specific measurement. For instance, a 1-inch tube with a 0.065-inch wall thickness is common for structural purposes, while a 1-inch tube with a thicker wall may be used for pressure applications.

[@Ajay_-pl8yj]

@@superfaststudyexperiment mai 4/5 EPC company me kam kiya hu mujhe ya jisko bhi a experience wale aadmi se ye questions puch lena. what in difference between pipe and tube Ans- Pipe ka OD fixed hota hai or tube ID

[@superfaststudyexperiment]

@@Ajay_-pl8yj wrong Answer