Here is how to grease the wheel bearing on your Honda Pioneer, the easy way.
Пікірлер: 63
@terryhenry824320 күн бұрын
Btw, the nasty looking grease on the hub spline you wiped out is a special grease and the one that should be used. The Honda service manual calls for it specifically. Molybdenum disulfide grease containing more than 3% molybdenum disulfide, NLGI #2 or equivalent. Example: molycote BR2 plus/ Dow corning
@JD-so6sk3 ай бұрын
I get to fix my cousins stuff, he got the 1000 in 2020 and breaks everything. About 20 tie rod ends so far. a few axles, a few ball joints, etc. Well he tells me his havent been working right for a few months, then front axle flew out. I go to assess it, and turns out all 4 wheel bearings went bad, the lose bearings caused the brake issues from floppy rotors, and made the front axle cv fail and fly out. The upper a arm bushings on drivers side are failed, along with all 4 a arm bushings in the rear. LOL at the bearing prices mentioned at the end. They ain't 25 bucks a piece anymore thanks to Build Back Better.
@Dmax043 ай бұрын
Sounds like he needs a tank instead of a SxS.
@Dmax043 ай бұрын
The bearings are sealed so you're not actually greasing the bearing. The grease is just filling the inside of the hub to keep dirt and water away from the bearing. I believe the tool is a 40mm for a 1000 Pioneer. I bought a 44mm off of eBay and it won't fit inside the bearing.
@JD-so6sk3 ай бұрын
its split in the center, and as you see on the tool, it pushes grease in the center split and forces old grease out. Yes it's called a sealed bearing, because its technically not greaseable, but this tool he has is how its greased.
@jesusojeda36854 жыл бұрын
Have 2,100 miles on my 2016 Pioneer, I never done it. But now I have second thoughts.
@charrheel36593 жыл бұрын
I thought only Polaris needed this. Never knew pioneers needed it also.
@DirtNDiesel3 жыл бұрын
Some people don't think so, but I liked too. By greasing the bearings it would push out any water or the contaminates prolonging the life of them.
@highland64392 жыл бұрын
Good to know all this stuff! Great information. I just ordered a 2021 pioneer deluxe. Can't wait. It is already built and just needs to be shipped to my dealer. Could be a month or more yet or maybe tomorrow? The dealer here never knows when they will come in.
@highland64392 жыл бұрын
If you stay out of the deep water holes like I plan to the bearings should be good for a longer time I would hope.
@ericfold68032 жыл бұрын
There is some serious satisfaction seeing that old grease, water and junk come out during the process. I change mine every 600 miles.
@jerryferrell5172 жыл бұрын
I've never been in mud or water over the bottom of the rim. I'm at 1850 miles now. Maybe I'll do this at 2000 miles. I already have the tool you show.
@brianv19663 жыл бұрын
Where do ya get that cool grease fitting tool, I need one! Thanks.
@buletpoint4 жыл бұрын
Your grease tool insert did not have the o ring on the back. The ones that do have the o rings allows for about 20 pumps of the grease gun per bearing. O rings keep it from leaking out the back side before greasing the bearing. My sportsman takes 20 pumps per bearing
@bobcallaghan15043 жыл бұрын
Where did you get that tool
@buletpoint3 жыл бұрын
@@bobcallaghan1504 Amazon
@TheCaperfish Жыл бұрын
mine has o ring on back side and is tapered on front side so grease can't escape and can only go up into bearing , that grease you see coming out back might be coming out by axle and not going up into bearing , grease comes out the front in the seam of the bearing so ya know its into bearing . , I remove snap ring so I can see when it evenly starts to come out , if not the snap ring blocks the pressure and it all comes out the gap in snap ring , as soon as I see it coming out I stop , I think its bad to have it totally full and will build heat and may even make yer balls slide instead of roll in the bearing , and yes rotate tool 90 degrees after each 4-5 pumps
@jerryferrell5172 жыл бұрын
Dang you grease the bearing and then spray carb cleaner in there?
@mattlemmens72665 жыл бұрын
Where’s the link for this tool
@hjonedmonds4 жыл бұрын
The best thing you can do for your bearings is to throw those wheel spacers away.
@bryanmontgomery40504 жыл бұрын
Yes but they track 1 1/2” narrower in the rear, my ocd won’t allow that. Haha
@rottiejakeluke3 жыл бұрын
How about a link for the tool to grease the bearings? What about a link for the arms? Thanks
@DirtNDiesel3 жыл бұрын
I got the tool on eBay , and my a-arms are made by SATV. Thanks for watching! www.ebay.com/itm/HONDA-PIONEER-1000-ALL-4-WHEEL-BEARING-GREASER-TOOL-axle-in-R/112540847698?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
@@DirtNDiesel Thank you man, Just bought my used 1000-5 and your videos have been Great for me to catch up with the Previous owners maintenance, needs and Mod Updates! Thumbs up for You, your time putting together, providing content and Wishing many blessings to you, your family and your Channel!
@DirtNDiesel3 жыл бұрын
@@georgeluna1084 Glad to be able to help, and thanks for watching!
@johnfinn2638 Жыл бұрын
what size is that grease tool?? same size for front and rear ?
@TPIindustries Жыл бұрын
Can you provide torque spec for bearing nut and calliper
@TheCaperfish Жыл бұрын
101 ft/lbs for nut and caliber is something crazy like 80 for front and 36 for rear , double check the caliber ones tho I just tighten until I feel good , but I aways torque axle nut . interestingly I marked all axle nuts before removing just for fun and 101 did not bring them back to where they were from factory so ?????
@bulldogtank14 жыл бұрын
what size greaser tool did you use for the front and the back?
@DirtNDiesel4 жыл бұрын
This is the one that I bought at the time. www.ebay.com/itm/HONDA-PIONEER-1000-ALL-4-WHEEL-BEARING-GREASER-TOOL-axle-in-R/112540847698?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
@rottiejakeluke3 жыл бұрын
Why the wheel extenders? Thanks
@DirtNDiesel3 жыл бұрын
I was making the rear wheel track the same as the front because I changed the rims out. It also made the buggy a little more stable. Thanks for watching!
@ellobo13262 жыл бұрын
I am not disagreeing with this video as I have little knowledge of this subject. But I have a 2017 Pioneer 500 and had a 2014 Pioneer 700 that I drove for years at my hunting club in much deep mud and water. Never did anything to bearings and never have had any issues. The guys with Polaris however replace broken bearings constantly. I’m assuming it’s difference in design ?
@rs-vl2im2 жыл бұрын
if u don't push out the old grease, mud and dirt using new grease, it will sooner or later catch up to you. mush easier and cheaper to follow this video then replace your bearings
@pushpushlambert80795 жыл бұрын
Dumb question ... Any noise, squeaks etc ... That would say your bearings are on there way to scrap ....
@carlatjoses5 жыл бұрын
I’ve never torn mine apart yet but it looks like a sealed bearing like a car. So my question , is there a hole in the middle of the inner race? If not the grease has gone no where but on the axle spline.
@DirtNDiesel5 жыл бұрын
When I greased the bearings with the tool the grease does go up behind the bearing. The grease in my opinion keeps water out, even though the bearing is "sealed," in my experience water still gets in. When greasing them it pushes out any water and dirt that may be in there. Thanks for watching!
@carlatjoses5 жыл бұрын
Dirt'N'Diesel ok wasn’t sure thanks have to get that tool.
@gsfbffxpdhhdf70435 жыл бұрын
Dirt'N'Diesel u are really really dumb. You dont know anything about bearings
@ripemm57374 жыл бұрын
Gsfbffx Pdhhdf not disagreeing but tell your expertise
@nicholashall16733 жыл бұрын
Will this tool work on the front as well?
@jimhafer2122 жыл бұрын
yes
@franknaaf48762 жыл бұрын
Does your tool work on your Kawasaki too?
@logandorries13514 жыл бұрын
Is that tool 44mm? Looking to get one
@DirtNDiesel4 жыл бұрын
Not sure on the size I picked this one up on eBay, I just searched for pioneer 1000 and it came up.
@bryanmontgomery40504 жыл бұрын
40mm I believe, the Polaris tool will work also.
@DirtNDiesel5 жыл бұрын
I forget to mention the front wheels brake caliber is 17mm while the rear is a 14mm.
@jimgideon33334 жыл бұрын
Can you tell me what tire and wheel package you have and the lift required to run them?
@DirtNDiesel4 жыл бұрын
The tire size is a 235/75R15 and the wheels that I am running are www.rockymountainatvmc.com/tires-and-wheels/kmc-xs128-machete-wheel-p?c=13 I was running a lift High Lifter Lift then moved to forward a-arms from super atv. I don't know if the tires will fit without a lift it would be close. I was also running a 1" wheel spacer in the rear to even out the track front to rear.
@jimgideon33334 жыл бұрын
@@DirtNDiesel thank you for the info brother!
@jimgideon33334 жыл бұрын
@@DirtNDiesel you are saying was, did you get rid of your pioneer?
@DirtNDiesel4 жыл бұрын
@@jimgideon3333 No I still have it, I am running a 4" portal and 35" tall tires right now and love it.
@fouryearproductions5 жыл бұрын
How often should you do this?
@adamneill92373 жыл бұрын
Every 1200mi when you change engine/trans oil & filters.
@jjjjjjjjrifufjssjosskenf5 жыл бұрын
I don’t get why you would even try to grease a sealed bearing. I think what you are doing is “cleaning” the outer bearing surfaces with grease.
@carlatjoses5 жыл бұрын
Jason Nadler I feel the same way but looking at pictures of the bearing it might be a split inner. But still has no way for junk to come out.
@bryanmontgomery40504 жыл бұрын
They do have a split center race. By greasing, you push out any contamination from the bearings. Most stock bearing come with very little grease as well. This is definitely a need to do item unless you like replacing bearings. I have seen them fail in as little as 50 miles if you ride in any water or mud.
@TheCaperfish Жыл бұрын
they are not "sealed" they are dust covers on them they will never prevent water from entering nor ill they prevent grease from getting out so it is fine to flush them with grease to rid any contamination in there and get rid of the old grease with metal wear particles in it that just acts like sandpaper and will wear bearings faster