WhirlpoolCabrio washing machine diagnostic mode with a touchscreen

[@jaimezimmerman161]

This legit saved us from buying a new washer tonight! I never knew there was a diagnostic menu and the code came back as the motor was burned out or something was caught between the basket and the tub... turns out our motor was touching our carpet and actually melted to the motor and was keeping it from spinning!!! Peeled it off the floor, raised it and boom, working wonderfully again, thank you so much!!!

[@NWinnVR]

I can't possibly imagine why people disliked this video. Exactly what I needed and no bs. Thank you.

[@bryanm5233]

Because they are washing machine repair guys

[@thatrandomchannel8589]

Didn’t show how he fixed it.

[@ninatheLMT]

Your video helped me clear codes on my washer and dryer, with no technical knowledge of appliances at all. Thanks so much!

[@josephseleenacarroll9832]

You’re a saint. A doggone saint. This washer is the only nice thing I claim to be my own and tonight, you restored it and my faith in humanity.

[@shushup3856]

Your instructions Worked Perfectly. Ran diagnostic code which I learned from a different video. F0 E3 were the error codes which means loans is too full or heavy. I was washing a queen size flannel fitted sheet and top sheet. This is a huge machine so no idea why it couldn't handle that. But had to re-spin each one separately per your instructions. Thanks so much for the video wish I had checked KZbin sooner. I wasted a lot of water and time. Couldn't find anything in the manual etc.

[@marieouellette1982]

I wish you showed how you accessed the drain pipe to clear it out.

[@nealrodneycassie]

Thank you so much for this video!! I thought I broke our washer and we'd have to buy a new one. Turned out it was just overloaded. Thought I was a goner when it refused to spin even after removing most of the clothes. Clearing the codes worked perfectly and I now have my clothes in the dryer. Thank you again.

[@stephanieweir629]

Thank you! Came home to the washer not working watched your video and now we know the problem before having to buy a new one thank you thank you

[@vondaflynn6620]

Mine will let some water in, but not enough water... like it shuts water off itself. Then throws LF code. Pressure is good. Worked great, then suddenly next time it does this... any advice or video on same scenario???

[@boostvic]

Change out the mini pump at the very top next to motherboard

[@shushup3856]

Thanks to you I was able to find out the error codes and solve my problem F0 and E3. Load to heavy. Washed a queen flannel fitted sheet and top sheet. It was too much for this HUGE machine. After finishing sheets were soaking wet. Had to spin them dry separately.

[@bluestripsmaney8322]

G. Celentano how did u fix the the washer

[@johnhancock7746]

You are amazing my friend!! I had no idea I could do a diagnostic and like many others thought I would have to buy a new one. I got the F8 and E1 codes and now looking them up in hopes I can fix it. I do know my wife ran a weighted blanket (things are really heavy) in it just before it broke so I wonder if that caused it to break

[@RealBlueLady]

How great of you to explain everyone’s error codes!

[@ffsteel111]

Blue Lady Just trying to help everybody out since my problem is difficult to figure out

[@siafulinux]

Thank you so much! Washer stopped filling with water. Ran diagnostic mode and had an error for it being overloaded. Cleared it and still nothing. Ran manual diagnostic mode (different video) and water ran through everything with no problems. Turned it off and on again and it's filling with water in the cleaning mode. You saved me from having to have technicians come into my home to "fix" it. (Unit is still under warranty but still...). Thank you again!

[@NiCholeMoody]

What video was this?

[@ffsteel111]

Glad it helped

[@joewhetstone4775]

So iv owned this set for a while and these cabrios are a nightmare but i urge everyone who has issues before ordering parts just clear the codes first then try it. Sometimes it just needs reset. Iv only ever had to replace 1 part on my washer. Luckily so far iv cleared the codes and it works perfectly again

[@joewhetstone4775]

Also this was a great video. Creator did a great job. 👍🏻

[@robselvidge2114]

Thank you. I was able to get my washer working again because of this video. You rock!

[@Chaser9124]

F5 E 3 The lid light comes on and is blinking . Any help in doing a hard reset as I tried doing exactly what you suggested, even unplugging unit . Thank you in advance .

[@pinklove7593]

I had the exact same code. Can you please share how did you fix the lid lock malfunction?

[@hknng]

That made my washer came back to life! Thanks for the tricks. It works for WFW6620HC0 washer

[@GabrielaSepulveda]

the model of my washer is W10607424B. This diagnostic mode also works for this model? Thank your for your help.

[@supertrav82]

How do you enter diagnostic mode on the dryer?

[@ttyl4027]

The man with the master plan! 💪🏿💯😤

[@johnhenrymusic4908]

Great info after I searched a bunch of sites and couldn't find reset info. Only question, it looks like you must clear the codes one at a time (at least that appears to be happening on mine); how many codes are stored (I've cleared at least 50 with more showing up), and is there a master clear way to clear all previous codes? TIA

[@30misswhite]

I have a f6/e2...but after I rested everything the washer will not turn on

[@aheenygo]

I really need a list of the different tests. I can't find them anywhere. I know the error codes but when I do test 50 nothing happens

[@alexanderboehme-mason7013]

Any idea why I have no power to the machine, ? Outlet works fine as I tested a small appliance to make sure it was working ok.

[@ffsteel111]

Obviously I would definitely check the outlet to make sure you don’t have a bad neutral or something like that but if in fact is good I would then open the machine and check the fuse. Fuses on you located after you see where the wires come in follow that circuit and you can see a fuse

[@Sorenlos2]

I really needed this video 9 months ago I had to buy a new whirlpool washer but huge thanks for the future lol.

[@ffsteel111]

No worries!

[@adamjacobs8715]

Would you suggest the whirlpool cabrio?

[@keithsanderson2466]

do not buy this piece of crap.It dosent get your clothes clean. go with a agitator style.

[@adamjacobs8715]

@@keithsanderson2466 thanks! I was eerie about the no agitator.

[@amarella_rue]

I have this exact model and would NOT recommend.

[@ashash4tube]

Oh my God the manual is so useless thank you so much for pointing out how to get into diagnostic mode

[@ellakad6148]

Mine The link F 2 F5 After disconnecting it I did it twice and it starts to work what do you think is the problem thanks

[@ffsteel111]

Sorry I’m not familiar with two of the same F codes . Most commonly the F5 error code is because of the Lid lock

[@joegillaspie6708]

I have a question about my dryer. It works just fine but it no longer beeps when it's turned on or the cycle is done. Do you have an idea what I should look at first? Thank you.

[@vickiedavis1275]

Do you have a video to show how to clean the drain pump filter on this same model?

[@blackgold2029]

I pushed those 3 buttons 3 times as you did in the video and nothing happened. How else can I get the codes?

[@ffsteel111]

Black Gold I would try unplugging the machine letting it sit for 10 minutes plugging it back in and then repeating those steps precisely. That’s the only way to get the codes out of the machine and that’s how the manufacturer designed it so it could’ve just been a one time mishap

[@clinkerclint]

Thank you! This is exactly what I was looking for!

[@ffsteel111]

Thx for watching and for commenting

[@doitlikepruitt]

Thank you. The only issue I am having is that the washer isn't doing cold water. And I checked the water lines and the blue is drawing hot water and the red is cool if I switch it should that fix it?? I just did the diagnostic test, and the fault code was F0E4, which is the hot /cold water fault. So I guess that answered my question. Thank you again for the video👍

[@ffsteel111]

It does sound like your waterlines might be switched

[@ffsteel111]

Also, double check on the back of the machine with the waterlines connect. There is a small filter make sure it is not blocked. If you continue to have the problem, you might have an issue with the solenoid valve on the cold side inside of the machine not allowing water in.

[@doitlikepruitt]

@ffsteel111 We switched the waterline, and now we have cold water. Thanks again.👍 If you have any more information about this washer, we would appreciate the videos. So we can repair it ourselves.

[@doitlikepruitt]

@ffsteel111 Awesome, I will screenshot your response so I can reference that in the future. Much appreciated👍

[@doitlikepruitt]

@ffsteel111 Awesome, I will screenshot your response so I can reference that in the future. Much appreciated👍

[@genj8983]

Wondering if you know why the 3 lights green, amber and red would come on when I press the start button. Not every time but here and there. It is the lights under the time of the wash circle. Thank you

[@ffsteel111]

I don’t know why those lights are coming up sorry

[@yriloeralewis4606]

Do you have to clear the code after you check the inlet filters, hoses, and drainage hose? Because I checked all of the possible issues and my washer ( whirlpool model WTW7500GC2) ran one cycle and the next displayed the LF code.

[@ffsteel111]

Yri Ruiz No they clear automatically but I would check your input water flow make sure they’re not obstructed and make sure the filters are clean in the back of the machine where you connect to hoses

[@Kimodoll__.]

I pressed the 3 buttons and nothing is happening. This happened about 2 years ago and I was able to find the diagnostic code but today nothing is lighting up. Ugh!

[@m.m.m.c.a.k.e]

Is there a way to pause after filling so I can soak clothing for hours instead of it draining after 15 minutes?

[@sexylover4812]

Please let me know if you found a way to do that, I've been wondering the same thing

[@hitmeback01]

I haven't used it for anything other than starting the washer, but there's a pause/start button...try pressing it at the point you want to let things soak. Maybe that'll work the way you want.

[@m.m.m.c.a.k.e]

@@hitmeback01 it drains and shuts itself down at about 15 min

[@hitmeback01]

@@m.m.m.c.a.k.e Bummer, sorry that wasn't the answer 😮‍💨. I should have guessed based on the amount of time pre-soak adds. Best wishes

[@BudgetClan]

Hello I had a code for and e1 and reset but still just beep and doesn't turn on.. any suggestions?

[@ffsteel111]

And e1 ? Never seen that come Up

[@BudgetClan]

@@ffsteel111I rest it and codes do not come out again... but still beeps and doesn't turn on?

[@tabithawest2736]

Hey. So mine is doing the same. When u say at the beginning u removed a black hose do u mean u literally went under the washer??

[@ffsteel111]

Yes you’re going to need to disconnect the washer from the wall move it forward and access it from the bottom normally what people do is tilted and let the washing machine rest against the wall as you work on it underneath.. remove the hose take out the pump look inside make sure there’s nothing stuck and try to spin it with a screwdriver it should spin freely

[@Blackwind_Legacy]

So I went to cleamine and then got a random set of letters and numbers blinking afterwards. Before i cleared it was only E1 and F5. I'm having locking problems.

[@amytorres1841]

HI I don't have a W1 model I do have a W0 I think I got it in 2016/2017 I'm not sure if I have warranty or not. My son put 2 comforters in the washer since then my washer been having a LF code. I can't put much in it anymore if I do it's 3 items tops like clothing if I add more it takes forever to add water then shuts off if I do have 3 items it suppose to run 45 minutes standard cycle but it'll take a good hour and half. it keeps adding time to the cycle time. Any help and advice would help me alot! thank you

[@ffsteel111]

Amy Torres I would check the fill tube and make sure it’s not clogged because the LF code means there’s a fill issue it stands for a long fill. When the water fills up there’s a pressure sensing module connected to a small clear pipe on the back of the unit near the tub and it could be kinked because of the large load inside the basket trying to agitate. After that large load you said your son put in there it might have kicked it at that time

[@universalsuccess3776]

How did you get no lights on from the very beginning?

[@jakealtamirano1852]

How do you clear codes on the dryer?

[@minieyke]

EDIT: Hang on, I figured out that the lights are blinking in your video due to the framerate of the video capture. However, mine only returns 8:88 with no diagnostic code. It double beeps every time I make a selection. Sometimes I can unplug it for a while and plug it back in, and then I can make ONE selection before the whole screen refuses to respond (besides power button) and just double beeps at me. I did press start one time, and it seemed to begin but then it stopped and double beeped at me. At least I know it's not a problem with the machine but with the shitty display. That diagnostic mode passcode just lit up all the buttons solid for me... which in a different troubleshooting page is something where you press all the buttons and then power last and it "resets" your display. I guess I've got a mutant. But it looks exactly like the one in the video.

[@janismcfadden9561]

Thank u so much for this video it saved money and I am absolutely grateful for it.

[@williross5170]

My whirlpool cabio washer is not dispensing fabric softener, I cleaned it and still doesn’t drain did error code and nothing there, help

[@cass9078]

I currently have a F9 and E1 code . My husband changed the hose . Could it be the pump is blocked ?

[@ffsteel111]

There’s an obstruction from the bottom of the washing bowl to the drain. It could even be the drain itself. One task you can do is take the drain hose out put it into a large wash basin sink and see if the same error code continues

[@cass9078]

@@ffsteel111 thank you

[@mikemoffa5532]

Great video! You saved me a bundle$$! Thank you!

[@dominiquefulmer6674]

I have the same washer and I am having some issues. I originally got the code f1e3 and replaced a cracked washer lid. After that the code F1e5 has appeared. I tried to google this code and read that the washer may need to be recalibrated. I ran the recalibration cycle or cycle 052 and then tried to use my washer. When I turn the washer on I can not change any mode and it just beeps at me when you touch the screen. I am not not getting any more error codes but still cannot use the washer. Does this by any chance sound like something you have seen. I would hate to buy a new washer because this one is only 2 years old but I have already put 3 hundred In for a new lid and still can not use the washer. any ideas would be helpful!

[@ffsteel111]

I am very sorry to hear that it sounds like you have had quite some unfortunate issues. If it’s just beeping it does sound like it’s in some type of programming mode I would try entering the diagnostic mode and then clearing any codes or just clearing it in general. Then I would turn the machine completely off by unplugging it and letting it sit for 20 minutes after that I’m not sure

[@dominiquefulmer6674]

@@ffsteel111 okay thank you? I will try this again and see what happens!

[@Tips_by_Audrey]

This is exactly what mine is doing. I have repeated all diagnostics, reset, power off for hours on end. Over and over too many times to count always ending with the same result. It just sits there and beeps at me reguardless what button I try. Very frustrating as this machine is like new and well maintained. Curious of the final outcome for @dominiquefulmer6674. What was the fix?

[@jovanagarcia8461]

I un plugged it connected it back in. Lid lock light stays flashing. What can i do to be able to run the diagnostic? Prior to this, washer adds time to any cycle even “clean washer”. Help me please!

[@ffsteel111]

I would try turning it off and turning it back on with the power button and then entering the diagnostic mode or try to press the rinse and spin button . If the lid lock light is still flashing that means it’s doing some thing and does not want to allow you to open it. Also try leaving the power unplugged for a little longer period of time to make sure everything resets

[@jovanagarcia8461]

Thank you!

[@lynnrantanen6400]

My whirlpool cabrio model # WTW7300DWO Is coming up with error E3 F7 can you please help? What do these codes mean?

[@ffsteel111]

The Cabrio Washer F7E3 error code means the main board has detected an issue with the drive motor or drive motor circuit. Drive module over current. Reset the washer by unplugging the washer for 5 minutes then plug it back in and see if the error persists. If the error quits and the washer is working after the reset then the main board just needed a hard reset. If it did not reset then check the lower wiring harness at the stator (motor) for any signs of wear or breaks or bad connections. If the plug and wiring looks ok then there are some diagnostic tests that can be made with an ohm/volt meter.

[@dqwon7930]

To easy. Your the best!

[@jackiewoolsey2247]

Our washer's error codes are E1 & F2 for stuck key. Do you have any suggestions?

[@ffsteel111]

Unplug the washer for five minutes, plug it back in and see if the board resets. If the board does not reset then you can try to take a hairdryer and run the heat back and forth over the user control panel and see if the key will unstick if not you will need to replace the user board :(

[@nicolebecerra6532]

Please help me. I was able to run a diagnostic check. I Fixed the issue. I even checked each step in the diagnostic mode. It worked perfectly. I cleared the codes but it doesn’t work on a regular cycle. What could be wrong?

[@ffsteel111]

I would try to clear them again and the. Shut it off unplug it and let it sit for 20 mins . Then try to turn it on

[@hameedazeez6981]

Hi Devon I have the same washer and it suddenly locked the door by itself and the board isn't working. I tried your techniques but it still wouldn't work, what should I do?

[@ffsteel111]

I would try unplugging the machine and leaving it off for five minutes and then plugging it back in and see if you can either start a cycle or run the diagnostic

[@hameedazeez6981]

@@ffsteel111 I tried that it still wouldn't work.

[@ffsteel111]

Put the machine in standby mode by plugging it in with all indicators off, or with only the Clothes Clean or Done indicator on. Select any one button except POWER, START, or STOP then follow the steps below, using the same button. Press/hold for 3 seconds. Release for 3 seconds. Press/hold for 3 seconds. Release for 3 seconds. Press/hold for 3 seconds. Release. If that doesn’t work try moving the lid and jiggling it making sure there’s no clothing stuck inside of it

[@quinndrueppel3345]

Thank you very much

[@fabianperea7563]

Could you help me with the F6 E2 code please? I would really appreciate it

[@ffsteel111]

Fabian Perea The Cabrio Washer F6E2 error code means the user interface board cannot communicate with the main control board. Reset the washer by unplugging the washer for 5 minutes then plug it back in and see if the error persists. If the error quits and the washer is working after the reset then the main board just needed a hard reset. If the reset did not help then either there is a wiring issue between the user interface and the main board or either the user interface or main board has failed. There are some diagnostic steps you can take using an ohm/volt meter that can determine if the user interface has failed

[@ricardolynch31]

@@ffsteel111 how do you reset the main board..?

[@GRIZZLY8800]

What if you cant get the codes to pop up.

[@cdcVintage]

You never have these kind of problems with washers made before 2010. You will be lucky if you get 3 years out of this. There are washers from the 1960's on youtube that are still working.

[@yvonkylatouche9282]

What about if there’s a code E1 or f2

[@rodrickjames3759]

I tried getting the codes error screen is not popping up

[@tamapeters184]

I moved and now plug in I have a f3 e1 what's thatnmean

[@ffsteel111]

Error code F03 E01 is a system designation of a problem with determining the water level. The first letter with numbers shows a sensor malfunction, the second one - to a specific damage zone. In particular, problems can be associated with both the central board and other elements: an analog or electronic pressure switch; a hose; a pipe; an air trap. First heck the water level pressure hose located between the pressure switch and the air trap. It can be twisted, pinched, bent, clogged, unsealed If all that is fine you more than likely have a bad pressure switch although it’s probably a twisted hose from moving,

[@Bey11ktb]

How do you reset the washer?

[@kings1372]

Is it normal for machine to still have water in it after washing?

[@kings1372]

It’s not high but you can hear it

[@ffsteel111]

If your wash is a little bit wet that can sometimes be normal although if there is water pooling in the bottom it’s not draining properly or not spinning properly check your drain

[@kings1372]

Devon Steel just found a small puddle under the machine this morning

[@ffsteel111]

There might be a clog in the pump located directly on the bottom in the dead center of the machine also check the hoses that lead to the pump

[@kings1372]

Devon Steel ok thanks

[@KolegrahmH]

The touch screen buttons aren’t working so I can’t put it in diagnostic mode to try and reset them or anything.

[@ffsteel111]

Might be a bad logic board or touch panel . Try unplugging for 30 mins and then try again .

[@doctorrockter]

Why is it still flashing after the reset?

[@thedanewayne6265]

I think it's the camera catching the hertz as most are 30 to 60 ECT.And the cameras capture frames or something faster than the displays ...cycling of electricity.Point at television and you'll see the bans Rollin up and down as you view thru cam corder,cell camera ECT.same kinda principle,I said same thing...it's still doing Ghost In The Machine....old police song/album.

[@NYKnicks6]

Hi Devon, you are so awesome by replying to everyone! I have an F0 and E5 code. Any help would be highly appreciated! Thank you!

[@ffsteel111]

NYKnicks6 The F0E5 Error code indicates that an off balance load has been detected. This means that the load in the washer/dryer could be too large, or it could be unbalanced. Avoid tightly packing the washer/dryer. Avoid washing single items. Balance a single item such as a rug or jeans with a few extra items. Note that an unbalanced load may not reach the intended washer spin speed for the cycle you selected. This could increase dry times.

[@NYKnicks6]

@@ffsteel111 thanks dude! After messing with it for a few hrs, resetting it with your instructions, and powering off and pulling the power plug for 5 mins then throwing in a medium sized load everything is back to normal. Thanks for the reply man!

[@ffsteel111]

Woohoo good stuff glad I could help

[@lolitaloc.875]

Could you help what F7 E5 please 🙏🏻🙏🏻🙏🏻🙏🏻

[@ffsteel111]

LoLiTa Lo C. This is a drive motor error. When the machine is started the sensing part of the load starts and usually when this error is present the machine will shut down after a few seconds and the lid lock light starts flashing. This means the main board is not sensing the rotation of the basket correctly or not sensing basket movement at all. First step in diagnosing this problem is making sure the basket turns free and is not jammed in any way. Then check for correct voltages at the main board (have yet to change a main board for this issue some techs skip this step and move straight to the shift actuator.) This is issue can also be caused by an optic sensor falure. The optic sensor is inside the shifter assy. You will the replace the whole shifter assy to fix the optic sensor failure. In my experience the optic sensor is usually the cause of this error. There is an optic sensor test you can access and by spinning the basket by hand the lights on the control will dance showing the optic sensor is reading movement. The exact procedure is in the tech manual. Normally the part replaced is the shift block actuator

[@ffsteel111]

Randy Crews so Cabrio Washer F7E5 error code means the main board has detected a shifter failure, this happens when the shifter is not engaging or disengaging for wash or spin mode. Reset the washer by unplugging the washer for 5 minutes then plug it back in and see if the error persists. If the error quits and the washer is working after the reset then the main board just needed a hard reset. If it did not reset then check the wiring harness plug at the shifter for any signs of wear or breaks or bad connections. Make sure the shifter can move freely and is not in a bind. Check for clothing lodged between the agitator/impeller and the basket. This could cause them to bind together and not allow the basket to engage this one I have seen to be an issue it could be a small piece of clothing maybe even a very tiny ladies undergarment.

[@n8kraft]

@@ffsteel111 I have this F7 E5 error on a wtw8000dw0. Where can I get the tech manual?

[@julianacombs3987]

US too :(

[@BeeTammo]

Thanks for the video, can you show how to clean the pump from whatever was clogging it?

[@ffsteel111]

Bee Tee I’ll try and make another video but the simple portion is you need to lean forward the unit Directly in the middle of the machine underneath the basket there is a white pump with two hoses that connect to it you take that off I think it’s three or four screws. And then takeoff the two hose clamps and then you can look inside the pump impeller blade and see if there’s anything fogging it you can also use a screwdriver to move the blade make sure it moves freely.directly in the middle of the machine underneath the basket there is a white pump with two hoses that connect to it you take that off I think it’s three or four screws. And then takeoff the two hose clamps and then you can look inside the pump impeller blade and see if there’s anything fogging it you can also use a screwdriver to move the blade make sure it moves freely

[@nicholasalaimo3156]

@@ffsteel111 i did all that and still the f8 and e1 is still showing

[@matthewplyler7155]

Thank you so much man i greatly appreciate your video and help

[@ffsteel111]

Any time!

[@bludiva04]

You just saved me!

[@chosenbyGod526]

Our washer is in the garage and temperatures have dropped so it's old . Our washer stopped working the water froze . My codes are f5 and E1 can someone give me directions on how to fix these?

[@ffsteel111]

I would first unplug it and let it sit for a bit and then plug it back in after that I will check and make sure that the door switch is working properly. That code indicates a door switch problem

[@hollyjo161821]

Thank you!!!!! This saved me soooo much time and $$

[@ffsteel111]

Glad it helped!

[@NiCholeMoody]

So how did you fix the E1 error code?

[@ffsteel111]

Ni'Chole Dixon Moody There would need to be another letter and number to find out what the issue is

[@thecamichanel7755]

Thank you, thi is model is new for my

[@ffsteel111]

Great!

[@paveldalesssandro6920]

How old is your machine

[@ffsteel111]

Pavel dalesssandro built in early 2018

[@paveldalesssandro6920]

@@ffsteel111 I live In A subdivision a d I have to replace all my appliances less then two years it all junk

[@ffsteel111]

Pavel dalesssandro why do you need to do that . ?

[@paveldalesssandro6920]

@@ffsteel111 because it all junk frig rusting washer dont work

[@ffsteel111]

Pavel dalesssandro sorry to hear that I have not had any issues

[@LakissaJ]

Hello! I can't even turn the wasger on nor raise up to top.... I still have clothes in the washer but can't even open the top.

[@ffsteel111]

Prodigystyler Gifted Unplug the washer and then but it sit for a few moments then turn it back on by plugging it back into the wall.

[@LakissaJ]

@@ffsteel111 I did that, No lights or nothing coming on. I don't know if i need a control panel or what... I don''t know what to do.

[@ffsteel111]

As long as you have power connected to the unit and you’re sure the outlet is good more than likely there should be a fuse on the board that has gone bad or your entire circuit board went bad possibly due to a bad storm or other type of short circuit

[@curseword3018]

I have an f5 and and e1 could you maybe help me with those codes, thank you

[@ffsteel111]

Zubaidah H that’s going to be a door lock problem .

[@dumplinsworld9496]

Tysm for the help! I was wondering could you help with f5e1?

[@ffsteel111]

DUMPLIN'S WORLD The Whirlpool washer F5E1 error code is a door switch error. When the door switch is open while the door is locked for longer than 5 seconds the main control will shut the machine off and report this error. Things to check: • Check for loose connections on the wiring from the door lock switch assembly to the ACU ( main control board). Make sure all connectors are seated properly. • Be sure you do not have the washer overloaded and that the load is inside the washer drum and is not blocking or putting pressure on the washer door. • If all the above looks good unplug the washer for a few minutes and restore power, if after restoring power the F5E1 error persists replace the door lock assembly.

[@msladywildcat40]

What if I get an f9 and E2

[@averygutierrez1853]

Very helpful!

[@Jyousa45]

Very useful, thanks 🙏

[@ffsteel111]

You are welcome!

[@davidcunningham00]

Thanks buddy

[@ffsteel111]

No problem 👍

[@Spideyface]

Very helpful thank you!

[@satsat969]

Thank you

[@brendadeleondemendez9572]

F6 E3 what do they mean

[@ffsteel111]

The Cabrio Washer F6E3 error code means the mainboard cannot communicate with the user interface board. Reset the washer by unplugging the washer for 5 minutes then plug it back in and see if the error persists. If the error quits and the washer is working after the reset then the main board just needed a hard reset. If the reset did not help then either there is a wiring issue between the user interface and the mainboard or the user interface or mainboard has failed. There are some diagnostic steps you can take using an ohm/volt meter that can determine if the user interface has failed.

[@321lmn]

f8/ e6 please. Ironically I just fixed my dryer today and then three hours later the washer gives out.

[@ffsteel111]

Sofia Ahmed The Cabrio Washer F8E6 error code happens when the main control detects water in the tub when the lid is open, meaning the water inlet valve is likely letting water in the tub when it should not be. This considered a Water Hazard Condition. Check the water level pressure switch hose from the tub to the main control for kinks, pinches or tears, also make sure its connected properly to the main control. Turn the power to the machine off or unplug it, does water still enter the machine? If so the water inlet valve has failed and needs to be replaced. Normally happens after A large load was washed . The tube gets kinked ..

[@saraali3109]

Any anyone fill me elaborate what is e1,f9

[@chrisescalona7428]

could you help me? I have a blinking blue light on my power button. no idea what this means.

[@ffsteel111]

Chris Escalona That should mean it’s in standby mode normally that happens when you press the button once and pause the cycle tried pressing and holding it to see if it changes

[@nthnthms1212]

When i enter the diagnostic mode, the only thing that comes up is 888. please help

[@ffsteel111]

Nathaniel Thomas 888 means the PC board is shorted and the display driver that shows what supposed to be a display is not working,I would take the PC board out of the machine,look for water corrosion,it will be like a white powder now if you see that,you have water damage from some other part inside

[@clairefromyt5561]

what’s F8 and E1?

[@ffsteel111]

ClaireFrom YT F8E1 Error Code - No Water Flow Detected The F8E1 Error Code indicates that the washer/dryer is not detecting any water flow going to the washer/dryer. This can be caused by several reasons, including the following: Washer/dryer may not be connected to the home water supply. Home water supply valve may not be turned on. Inlet hose to washer/dryer may be kinked. Make sure that the washer/dryer is connected to the home cold water supply, and that the home water supply valve is fully open (turned on). Verify that the inlet hose to the washer/dryer is not kinked.

[@clairefromyt5561]

Devon Steel Thank you so much for answering my question. 👍👍👍

[@DennisSantos-bo6wl]

Whirlpool cabrio wtw7300DW0 F1E2 code how do calibrate it please

[@ffsteel111]

Bad motor …

[@gregscalley2412]

What is F7 E8? I can't find that code.

[@ffsteel111]

Greg Bryan hey Greg that means it’s a high temperature motor error ! It could’ve been because you had a very large load of laundry or something got stuck during the cycle I would recommend unplugging the machine and resetting it and turning it back on and if it happens again there could be something stuck inside the basket underneath. appliancerepairguides.com/whirlpool-cabrio-washer-error-f7e8-explained/

[@benjaminandersen9650]

Thank You for this video but i hate this washer because it has to be the worst washer i’ve ever owned.

[@so-caloutdoors7210]

Thank you !!!

[@cosmicvcosmic]

i got F3E2 and cant find it on manual anyone know what to do?

[@ffsteel111]

First of all, pay attention to the pressure switch hose and air trap tube. They are often the source of the problem, since a dirty fluid leaves deposits on the walls, narrowing or clogging the gap. In the end, examine the control board because it also causes error code F3 E1. Look in the pressure switch make sure it is clear and the hot is not kinked .

[@kevs3266]

what is error code f6 and e2

[@ffsteel111]

The F6 E2 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.

[@Hollywood2019]

I have an error code of f7 & e9 please help

[@ffsteel111]

Kenneth Howard ERROR F7E9 The Cabrio Washer F7E9 error code means the main board has detected the motor is not moving when its suppose to be, this error is classified as a locked rotor. Check for clothing or other items stuck between the basket and tub which could be causing friction on the drive system or stopping the motor from spinning the basket.

[@Cynthiat246]

I have an F8 and E6 can anyone tell me what those codes mean?

[@ffsteel111]

Cynthia Tarpy From the research I was able to do the F8 code board failure ,although the combination you’re seeing on your machine I’m on able to find. I would try contacting Whirlpool and see if they can give you any further details sorry I don’t have an answer for you on that one . I would try to unplug the machine and let it sit unplugged for about 30 minutes and then plug it back in and try again . Also make sure you hear the lid lock after and you start the cycle. I’ll let you know if anything else comes up

[@ffsteel111]

appliancerepairguides.com/whirlpool-cabrio-washer-error-f8e6-explained/ Look at this link here might be your issue

[@ffsteel111]

Looks like it’s your water inlet valve possibly needs replacement

[@carriemiehlich258]

What if you cannot power off

[@captkillionsparrow]

2024, this might have saved us from calling a repair tech or buying a new washer!