This TRICK with BEARING and a ROUTER will drive you CRAZY | Woodworking tips

[@annelarrybrunelle3570]

Note: since you can place tbe center of the tenon and the center of the hole, even on the angled piece, just DRILL both of them for a sufficiently large hardwood dowel. Then you need neither the bearing nor the router and bit. Spend the tool money on a Forstner bit. Look, I'm impressed with your steady hand on the trim router, and you got away with it, twice. With a small router like that, you MIGHT be able to do it successfully a number of times. Sooner or later, you'll tilt the router a degree or so off, and tne bit and the bearing will do something noisy and scary. The kick might surprise you, and NOBODY's reflexes are that fast, not even a snake's. If you HAD a real necessity to do something like this, first make a jig that can support both the workpiece and the router OUTBOARD of the cut. In place of the bearing (there's already a bearing on the bit), use a correctly-sized disk of hardwood or aluminum, fixed in place by a recessed screw; this serves as a template and inner support, and the table you build into your jig provides the outer support. That table needs a big enougb hole to allow your traverse about the tenon you are making. Thinking further, you could invert the whole jig to use on a router table. And there are other solutions that won't risk your digits - and your eyes and other valuable parts.

[@hansvonhamburg6370]

Gut, dass ich immer ein paar Ersatzfinger in der Schublade liegen habe.

[@sergeynazarov8773]

Этот трюк не только сведет с ума, но и оторвет палец..

[@robertsoncletokoerner7012]

Parabéns pelo seu ensinamento, obrigado! Robertson (Brasil)

[@francisco-kb7mv]

It’s cool It.

[@MCsCreations]

Wow... Idea sensacional, Will! 😮 Principalmente pra fazer pés pra mesas e branquinhos!!! Abraços e se mantenha seguro aí com sua família! 🖖😊

[@WillWoodDiywoodworking]

Valeu meu amigo! Sim uma ideia bem legal para encaixe, obrigado por assistir e deixar seu comentário. Tenha um ótimo domingo. Abraço 😉🙏👍

[@jaspalmanku3684]

Ingenious 👌👍👍

[@Alessand-p2j]

Отличный вариант👍👍👍

[@johnschuster9192]

Awesome deal!

[@WillWoodDiywoodworking]

Thanks for watching and leaving your comment 😉👍🙏

[@thomaschandler4831]

Genius 👍👍

[@pauluspriems4442]

Well, I thought that was brilliant!👌

[@WillWoodDiywoodworking]

Thanks for watching and leaving your comment 😉👍🙏

[@billF2380]

But for balancing a router on a bearing…

[@romanvogler5458]

Yess, me too! i was in search of a tutorial to cut my fingers in a verry quick mode!

[@09FLTRMM77]

MM77 Approved 👍🏻 👍🏻

[@WillWoodDiywoodworking]

Thanks for watching 😉🙏👍🙏👍

[@ArgondIron]

С первой секунды убил наповал - не смог в центр по разметке попасть :)

[@ferfer6102]

Gracias, like y nuevo suscriptor.

[@bearsha]

Я сошëл с ума.... Теперь мне нужно закупить кучу подшипников....

[@МенеджерФайлов-х2щ]

мне тоже капец

[@pabloalvarez6671]

Excelente idea, gracias por compartir 😊. Saludos desde la Argentina 🇦🇷

[@WillWoodDiywoodworking]

Thanks for watching 😉🙏👍

[@brianfoster7064]

Horrible idea, unless losing fingers is your idea of a good time.

[@polpol2803]

Думаю что имеет право на применение. Хорошпя идея!

[@MarcolinoLara]

Grato: aprendi (+1)!

[@jorgedanmen8412]

Muy buena idea. Que medida de ruleman o rodamiento usas para la testa de la madera? Gracias

[@Ричи-и9у]

Обезательно куплю себе такое шило...

[@MacDa-yy8xn]

All I can say is YIKES!

[@Prihodsky]

Это нормальный способ в полевых условиях. Но я бы положил на стол брус, равный по высоте с подшипником, чтобы основание фрезера опиралось ещё и на плоскость рядом. Потом заготовку можно поворачивать на 90° или 180° и обработать с хорошей точностью.

[@joelrob8606]

Génial. Merci

[@dentailers]

Фокус-Покус 🎉

[@cahndeso9080]

bagus

[@garymucher4082]

If you are going to have to use a forester bit anyway (or basically any size drill bit for that matter), why not cut both pieces of wood with the exact same bit and use a dowel. Would sure speed up the joint and be as tight as well... JMHO!

[@СергейВласов-х2с]

Супер опасный трюк! 👎 Даже не вздумайте это повторять.

[@ArgondIron]

Тот случай, когда подшипник не выпрямляет руки растущие из заднего прохода.

[@Aprendiz-de-Marceneiro]

Isso pode ser muito perigoso para sua saúde! 😂

[@willwatlington6750]

DAMN!!

[@lommmaster]

Походу, только тебя свел с ума этот трюк. Да и не трюк вовсе, а всем известные истины, Карл!

[@ВячеславЗамураев]

ОТЛИЧНАЯ РАБОТА!

[@ArgondIron]

И со второго раза при разметке в цент попал, а при сверлении не попал :)

[@sergueiothonucci1638]

😃😃😃

[@WillWoodDiywoodworking]

😉🙏👍

[@wayward-saint]

Such an underwhelming result for how dangerous it is to use a router like that. I’m asking KZbin to not recommend this channel to me anymore. Anyone who wants to keep their fingers should do the same.

[@ExploringLifeWithChris]

Thanks for trolling and showing the world how bad your personality really is.

[@madeirareaproveitamento]

Eu também fiz isto, estou preocupado em fazer novamente, pode explicar qual o perigo de segurança?

[@bobreese8831]

Seeing part of your hand below the plane of the router base concerns me. Not sure what the better way is, but I’ll pass on this tip for myself.

[@slickpbw331]

I count my 10 fingers out loud before operating any power tool, and I would never do anything like this.

[@ArthurDeurer]

I agree. It is a very dangerous work with the router!

[@ергариг]

А не проще ли коронкой этот трюк сделать? 😊

[@DrParamon]

Подивився. З БОЖЕЛЯ не зійшов.

[@ashleyhunter3300]

You are lucky you still have all your fingers ! Both the chop saw and router ! And all that for a sloppy joint ! I will pass.

[@sasquatch-7634]

Great idea but any round thing could also be used like a piece of dowel or even a jar lid.

[@WillWoodDiywoodworking]

Thanks for watching and leaving your comment 😉👍🙏

[@Tigdude]

Got to be a better way...ouch

[@Icantball67]

Yeah and he hit the bearing with the router. How much longer is that cheap router bit gonna last when you hit metal?

[@BraunBruno-br5jm]

pensavo di essere solo io a pensarlo, ma leggo da altri commenti che la sicurezza in questa lavorazione lascia molto a desiderare ... secondo me questi esempi di lavorazione non dovrebbero nemmeno comparire in foto. Ottimi altri video, ma questo, per correttezza dell'autore, dovrebbe essere eliminato.

[@richardthomas1566]

That router rocking around on that Bering ? I could have done better with a butter knife . Just use a hole saw

[@dvjchitamaster]

noooo me gusto

[@Виктор-с4э1б]

Я уже вижу , что сошол .

[@jorgeantonioramirezromero5598]

en que parte esta volverse loco,NO ENTIENDO

[@kizilkedi8604]

You must be out of your mind to do that. It is too dangerous. If it slips you would lose fingers maybe one eye.

[@sergeykarnauhov5796]

1:16 ✨?

[@valeriuconstantin]

[@олегевсельев-ф2ю]

Опасно. Не повторять!

[@vitosm4234]

Навіщо підшипник, якщо на фрезі вже є підшипник? Можна було використати щось інше круглої форми і не вкручувати гвинт, а приклеїти, а потім відірвати, не пошкодивши дерев'яну заготовку

[@СергейПолищук-г4н]

А нафига коверкать два языка сразу? " стоишь на останивки"? 😂

[@Манах_1й]

ДРОЧЬНЯ СОБАЧЬЯ !!! 🤣🤣🤣

[@Lobzik67]

As a woodworker with 20 years experience can tell you "don't fk do it!!!!!"

[@АлексейГаак-ю7з]

Why?!

[@Lobzik67]

@@АлексейГаак-ю7з пРОСТО ПОВЕРЬ НА СЛОВО

[@renullyou]

​@@АлексейГаак-ю7з там выше есть подробный коммент на английском. Если фрезер чуть сместится, то фреза заденет плохо закрепленный подшипник. Можно получить травму

[@hunglikeahamster]

No thanks

[@maildcastro]

Really dangerous technic.

[@maildcastro]

And poor precise.