show the part where nylon cord gets around the glass at start.
@charlesrosaly21 күн бұрын
Right!
@vsinulingga19 күн бұрын
Thats the secret
@PorkyHontas19 күн бұрын
Bingo! That's what I want to see too.
@marcelllegend884418 күн бұрын
so the string is placed in a crack somewhere out and is looped back in the glass then pulled threw
@donnoelvideos18 күн бұрын
@@marcelllegend8844Mas igual não explica, ele tá tirando ou colocando o vidro ⁉️🤔
@user-qw3jn7bd7i4 күн бұрын
실은 어찌 집어넣었나??
@droo946622 күн бұрын
What we really wanted to see is how he got that thread in there between the window gap
@ChesareAugustus19 күн бұрын
That takes almost 3hours!!
@conradgil62119 күн бұрын
Yes I want too also
@Grey.S18 күн бұрын
Все очень просто,для этого используется длинная крепкая игла,похожее на шыло.
@user-zu4zv6nb2u12 күн бұрын
Yes thy dont show that
@drdeathkitty7 күн бұрын
You basically just shove it through on the tip of a spike.
@2NRxK5626 күн бұрын
Terbaik bang Bole tunjuk sikit tak mcm mna masukkan cable tu kt celah cermin😅 Banyak kali tgk video abam Terpikir mcm mna selit cable kt celah cermin Tapi mmg terbaik bang👍🏻
@AbamRongg25 күн бұрын
Boleh… Terima kasih support bang💪
@2NRxK5625 күн бұрын
@@AbamRongg sama² bang🤙🏻
@TukulYgTersakiti24 күн бұрын
masih ingat 20 thn dlu buka cermin guna cable brake basikal,,sorang tarik dari dalm,sorang tarik dari luar,,berpeluh juga ketiak kena..ahahah
@luisitoiban200823 күн бұрын
Esa es una de mis preguntas también 😅😅😅😅 es imposible sacarlo así.
@mehmetsakar612523 күн бұрын
Misinayı dışardan ucunu söküp,matkapla doluyorlar.camcılarbu işi naylon ip ile yapar
@hoppykengka822623 күн бұрын
Yeppirs, the missing part is where the loop is pushed out -- actually, could be anywhere ...BUT... unit is installed where the rear view mirror was. hmmm, so if the loop ends up at the top, then it is pushed through at the bottom center of the windshield, pulled ALL the way around the perimeter, and --voila-- wind each side a bit at a time and done. (btw,what you don't see is the 170° heatgun following ahead of the cable to soften the bonding agent a bit 😉)
@AbamRongg22 күн бұрын
Nah, tbh i didn’t use heatgun
@user-jp6zs1qe7q22 күн бұрын
Lo único mal det trabajo que hayan recargado el vidrio roto en el vehículo.
@user-bq3og5pz9w20 күн бұрын
Missed out the important bit 😂😂😂
@reinerkrueger858224 күн бұрын
Da fehlt der Part wie das Seil in den Scheibenrahmen eingefuehrt wird.
@diegorios15424 күн бұрын
Your right
@francisvantuyle23 күн бұрын
That is the secret you pay for.
@user-ri1gv4vm7e22 күн бұрын
Your right I'm looking and nothing is showing
@3lack_shadow10722 күн бұрын
ใช่มันคือการ ตัดต่อ 😂😂 ไม่มีช่างคนไหนอยากบอก
@eugenecundiff-nv2tn27 күн бұрын
What about the plastic guid tabs at bottom or in corners does it cut through those as well. Or did that windshield not have those and only urethane.
@GetachewFraw24 күн бұрын
😊😊😊
@alfredofuentes246522 күн бұрын
It cuts through them like butter
@jw70372 күн бұрын
It will cut the metal before you even notice it
@miltonwilliams239919 күн бұрын
Where did the string come from? And how did you get the string into the windshield? This seems very tedious
@Smurf_GT118 күн бұрын
Wire feeder. Peirce it through the bottom. Between the glass and dash.
@user-bk3wp4xz9e20 күн бұрын
А почему непокозал как нить он заправил внутрь ааа????
@user-jl3qq1cw1z13 күн бұрын
Шилом
@kevinmaxwell661011 күн бұрын
No more scratching to the bone. I assume the surface should be flat enough to re-glue the windshield. If not, I've scraped gasket off aluminum surfaces and know that with everything clear, the gasket can be removed gently without scratches. I really like that tool. Nice job and great video, thanks.
@johngregg918721 күн бұрын
Doesn't show us how to get the wire in the windshield (to push the trigger)
@abucompu21 күн бұрын
And that is the fish line it will snap easily
@alcarasjosehiram318421 күн бұрын
That is my question too
@spy200321 күн бұрын
Me to 🇬🇧
@BigandSocuulant20 күн бұрын
With a long tool usually you pass it through at the bottom. It’s like a needle 🪡 very easy.
@Smurf_GT118 күн бұрын
Wire feeder. Peirce it through the botton between the glass and dash.
@christinarussell457623 күн бұрын
Safelite used this tool to remove the windshield from my 2011 Hyundai Sonata SE 2.0T about a month ago. So much easier than doing it the old fashioned way.
@kevinl323522 күн бұрын
Very cool! I'm trying to figure out how they get the cord started around the window trim without pulling off all the panels?
@user-ri1gv4vm7e22 күн бұрын
But how you insert the wire 😅
@bladerunnerpeter16 күн бұрын
Se inserta con una espada que engancha el cable de dentro para afuera por la parte del salpicadero hacia afuera luego rodead el cristal con la cuerda por fuera
@atikaziz271423 күн бұрын
Mantap bangrong,penah buat dengan dia dulu,dia seornag yg komited,dtg rumah naik kelisa masa tu,ingat lg,semoga terus maju jaya bangrong
@AbamRongg23 күн бұрын
Zaman naik kelisa zaman aku mula2 tu, terima kasih bang pernah support kawan 🙏
@davereynolds707021 күн бұрын
That’s coooollllll, I wish I had that when I was building salvaged vehicles as a teenager years ago
@damienkram337925 күн бұрын
Fun fact: Volvo using device like that in they services back in 2001.... It even has part number...
@cameronbartlett659310 күн бұрын
Fun Fact : Not all Fun Facts are Fun Facts
@luigipellegrini922122 күн бұрын
How do you put the strings inside the glass perimeter, I didn't see that one 😅
@Recowreckin19 күн бұрын
I wish u shown step by step im wondering where the wire was placed
@Hottnutz9819 күн бұрын
I'm with you. They are skipping the part I actually want to see
@TheDomaradzki18 күн бұрын
Isso mesmo, contou o vídeo. 😮
@Berserk9999999920 күн бұрын
Классная вещь. Помню вынимал окно, с помощью канцэлярскаго ножа и тросика и это был тот ещё сэкс!!!
@jchristino10 күн бұрын
Sempre foi feito assim. Até hoje. Será que essa geringonça é boa?
@ebbeweber131024 күн бұрын
I miss the good old days when the glas was easy to remove and fit by yourself. Nowdays the shit is glued and part of the cars structual integrity...😮
@rudijuli928223 күн бұрын
Bahase apeee tuuu
@jondoe8889Күн бұрын
And the glass is thinner and cheaper to save money and weight. I have a car with a glass roof, and make sure all the glass is insured.
@Asad-216622 күн бұрын
Sorry you didn't show all of it!!!
@johnedwards174620 күн бұрын
So how’s the wire get around the screen at the beginning??
Eso también yo no entiendo cómo fue a quedar el hilo verde en el vidrio como lo metió en que momento hizo eso
@haridas861721 күн бұрын
If you wanna remove then why to put? First put , then Removae .... But why?
@chancesgoman975519 күн бұрын
Watched a guy put a windshield in a jeep yesterday. He used a reciprocating saw with a giant butter knife blade . Way easier than this contraption.
@JayRose9045 күн бұрын
Yea that works on alot of them but not all
@TheWorld-of7dd20 күн бұрын
Boleh tunjuk cara masukkan tali nya? Dan d mana boleh beli alat tu
@sayramcity352320 күн бұрын
А как запихнули нитку в лобовое стекло
@tanayaman313914 күн бұрын
Этот секрет уже бабки😊
@user-jl3qq1cw1z13 күн бұрын
Ну обычно шилом с крючком ,в герметик который между стеклом и кузовом .Как сапожник)
@imbattosai231920 күн бұрын
Wiihhh.. Mantap abang ini cara melepas kacanya ..👍
@lt507113 күн бұрын
They’res a aftermarket windshield guy across town 79.99-99.99 installed for most cars. It’s a little bit cheaper quality but works , but better than 400.00 at the dealer.
@DeliciaDiaz-eo9rm22 күн бұрын
🐐no grabaste donde como pusiste la tansa para q despege el vidrio 🙄
@raulpujolspromo340322 күн бұрын
No hizo nada
@NEOSPORIN777720 күн бұрын
you didn't show anything with the yellow cord 😮 FAIL!
@pepeneri695020 күн бұрын
No muestra como introducir rl hilo.
@josedenobrega149724 күн бұрын
Só complicão saudades dos carros anos 85 pra baixo
@peacefromislam47821 күн бұрын
At my place they just used a small fire instrument, melted the glue, and removed it. Just took 2-3 minutes.
@user-mg2ku1hk1j23 күн бұрын
ذكاء ومعرفه بالتعامل مع العمل
@NoNotMe000020 күн бұрын
Window replacement yes "Fast and easy" No.
@SillyNorule21 күн бұрын
ガラス外し自体は優秀ですが、外したフロントガラスを車に立て掛けるのはやめて欲しいです。
@robertoc.abrahao811910 күн бұрын
ほんとだ!
@nostalgy610 күн бұрын
どうしてですか?
@SillyNorule10 күн бұрын
@@nostalgy6 車に傷がつきますから。
@nostalgy610 күн бұрын
あー、ならほど。
@xxbonrockxx9 күн бұрын
Exactly! You never lean anything up against a car's painted surface. For one, it can cause damage, and two, it's just disrespectful.
@Freddy-kk2dj23 күн бұрын
Excelente herramienta
@joseluishernandez196121 күн бұрын
Y funciona para retirar el sello del parabrisas de un autobús si es así donde consigo esa herramienta de que pais
@Kymyk0521 күн бұрын
Нихрена не понятно, но очень интересно
@paulfernandez269523 күн бұрын
😮😮😮asombrosa maquinaria😮😮😮
@mohamadasri271521 күн бұрын
Mudah zaman skarang.. Dlu2 masa study dgn keja nak pasang cermin pakai tali lembu ja sorg luar sorg dlm tarik😅😅😅
@anammme_1820 күн бұрын
keknya itu tali yang di mesin di copot dulu itu kan kiri kanan tali nyambung cuman 1 tali , jadi itu copot trs di selipin kiri kanan kaca ntar di masukin kek mesin ya dah deh tinggal bor ,logika gw gitu sih
@willanderson508822 күн бұрын
I’d have been putting it back in before they got it out. Cool tool but slow
How u getvthe wire undervthe windshield seems more importantvthst showing pumpimp amd 30 seconds of an impact gun
@Abdullah.534627 күн бұрын
Çok başarılı ❤
@juanramonjoaquinhuanca937921 күн бұрын
En peru lo sacan cin una soguita sin maquina ni taladro
@dfr-wx9yk21 күн бұрын
Benar Bung tapi saya rasa awalnya seluruh negara😅
@bbbbnmmmm400522 күн бұрын
Hi brother I need this tools can you tell me where I can buy it
@darrenbaptiste350219 күн бұрын
HOW DO I ORDER FROM TOBAGO 🇹🇹 VERY INTERESTED
@rizalherlina660420 күн бұрын
Gmn cara masukin talinya
@BigandSocuulant20 күн бұрын
Long tool like a needle 🪡
@PaddyOhMally20 күн бұрын
Nice maybe now your car won't rust through in 1 year after some doofus with a scraper takes all the paint off while changing your windshield
@Avitenjenering01RudiEnje-bq3gp11 күн бұрын
Ap NM benda yg buat bukak kaca tu boss,dmn beli alat nya. Serius nanya.. ✌️✌️ 🙏🙏🙏
@eldarelekberov577020 күн бұрын
How can I get this tool?
@jdvlog709820 күн бұрын
U don't needs this you needs an steel wire put in window nd pull all sides
@robertserr33565 күн бұрын
And two (2) people.@@jdvlog7098
@Ivan_GC19 күн бұрын
Tengo un amigo que los quita en 3 minutos y a mano
@luisantoniogonzalesrios193119 күн бұрын
Aquí en Perú también!.... Jajajaja!
@nimagharibpour220523 күн бұрын
What's the tool name and where we can find it
@aeddyktmb317219 күн бұрын
Kedai kt mana tuan..boleh claim insuran x nk tukar cermin
@led303321 күн бұрын
줄을 어떻게 꼈을까?
@spy200321 күн бұрын
Exactly 🇬🇧
@jccv734920 күн бұрын
Genial 😄
@lyhiencicimore495226 күн бұрын
Dulu buat manual .pkai cable brek basikal .tarik kanan kiri tp mkn masa nk buat .lenguh tangan
@AbamRongg25 күн бұрын
Betul, tiada yang dulu tiadalah yang kini 💪
@S3sahabatsehobbyselamanya575823 күн бұрын
Wah ini baru canggih alatnya,soalnya nyopot kaca dgn silent original nya sangat susah dan bisa tapi lama dgn metode manual 👍yg saya pikir bagaimana cara kabel tis nya itu?mohon petunjuknya maseee 🙏🙏🙏
@jorgeortiz111221 күн бұрын
Compa porque la mayoría de personas y también tu eres uno de ellos que publican en las redes sociales , pero no explican completo el contenido. Mejor no vuevas a subir contenido si no lo piensas explicar bien..
@user-so5ry3xr7v20 күн бұрын
No sirve perder mucho tiempo
@UNCLEFIX-el2ro21 күн бұрын
What the name of this tool?
@e.r.t.5832 күн бұрын
I use to install windshields back in the 70-80s and I had to cut it out with a pull handle knife This makes the job so much easier I could do it now at 67 and even setting the new windshield even easier than by holding it by hand and arm strength
@marvin482721 күн бұрын
A cinder block does it in 0.351 seconds....😂😂I
@luisnunez-jf6uj19 күн бұрын
Nice job but they messed up the front bumper laying the glass on the front bumper 😂😂😂😂😂😂😂😂😂😂😂l😂😂😂😂😂😂😂
@ariffinspark1588Күн бұрын
Salam bang rong,cermin retak leh repair x,cermin perdana
@SETtheTONE.20 күн бұрын
1-2-3. Nice tool.
@ZaifaTpod18 күн бұрын
Ada buat claim insurance cermin ke
@s.h712423 күн бұрын
How did u get the wire to the other side ? The most important part need to see
@victormanueldelgadorico534122 күн бұрын
Alguien me puede apoyar en como se llama esa herramienta o donde la puedo adquirir
@user-wo1gl2jj1y19 күн бұрын
前檔玻璃更換的過程 用線切 是很好的方式 不會傷到板金 油七
@user-jn1ge7xc1e17 сағат бұрын
ワイヤーをどうやって接着面に入れてる?
@duartetx14 күн бұрын
Me manda o link de onde posso comprar essa ferramenta por favor.
@ronnyrodriguez987123 күн бұрын
Soy de República Dominicana y ese es mi trabajo, y llevo tiempo queriendo conseguir esa maquina, me puede dar información de donde la puedo conseguir?
@user-op7gt8lo2s14 сағат бұрын
اللهم ارزقنا حسن الخاتمة
@ajatruni779821 күн бұрын
Cincinya bagus tuh..
@sergiozuniga663815 күн бұрын
Donde se puede conseguir esa herramienta??
@automotivesolutions791719 күн бұрын
Hi I am interested to buy this product. Can you share the details
@dwiharyanto623223 күн бұрын
Dmn bisa beli alat itu,dan brp harganya om..
@willyspeed41556 күн бұрын
Saludos donde puedo conseguir esa makina
@spasi5712 күн бұрын
I used to do this job and remove the windshields by hand with a friend. Is less complicated and also faster than this.
@cross5kion14 күн бұрын
ガラスに糸通す時どうやってるんだろう?
@hairulamran471813 күн бұрын
bang tuka cermin alza 2012 berapa
@user-qn7dv5vt4x23 күн бұрын
請問這工具哪裡能買到呢? 非常需要?價格多少有人知道嗎?
@hasmadiadri791023 күн бұрын
Terbaik AbamRongg,dulu pernah tukarkan cermin teksi saya di hadapan tropez residence danga bay
@user-mc5wg9iq6e23 күн бұрын
す😮😊😅
@DaxL_net19 күн бұрын
How did the thread get on the outside of the car screen? Or its magical?
@Indigo3.712 күн бұрын
How well does it work with a shattered and big-time cracked windshield?
@maurolemes42118 күн бұрын
Onde posso conseguir essa máquina??
@sudarshanmonotraveller411621 күн бұрын
He should not run middle of the pitch. 😮 Do you know the rules or shall I explain 😅
@JOSEDIAS-jg7dr19 күн бұрын
Muito engenhoso, top👏👏
@rolandoperezbejar843219 күн бұрын
Donde puedo adkirir..esa herramienta
@mohamadridhwanbinroselanmo161619 күн бұрын
I dont get it,did you need to make a little bit of spaces between the windshield to make tht wire get through?
@user-pc9cy8mu1j23 күн бұрын
Kami dulu potong guna tali gitar je,sekarang special toll banyak dah senang buat kerja
@ibbut453520 күн бұрын
Boleh jga tuh batu cincinya😂
@arieshah619320 күн бұрын
Nak Tanya. Kenapa cermin yg dah bukak tu mesti letak sandar depan bonnet kereta ye. Macam tak sesuai je letak depan Tu
@thekotoamatsukami40920 күн бұрын
Cermin tu bukan cermin baru, tu cermin yang dah rosak atau perlu dibaiki