Worm Gear with Motor DC 12V 12RPM | 5840 31zy | DC Motor

Hi all! Review of a powerful 12 volt gear motor.
Super powerful motor for any robotics.
Subscribe to my youtube channel!
There will be many interesting projects on the channel soon!
Put a like under the video!
Comment!
Thanks for watching!
My Instagram
/ texacitcompany
#gearmotor12v #584031zy #dcmotor #robotics #technology #electronics

[@azman4749]

I just finished a low speed hand held 2" wide belt sander using that black 24v 120 rpm motor. Quiet and power full motor. But i just ordered a new same motor with 480 rpm as 120 rpm seems very slow for that purpose. I actually made same project using the silver colour (12volts 480 rpm) motor as shown but it a noisy motor and become hot to touch after using it around 10-20 minutes. Worse, the gears went kaput after a used it for a while. Not very robust gear for a heavy loads but the motor seems fine.

[@Robotics_Robot]

Hello! Yes, black engines are reliable and expensive. And whites sometimes have problems with the gearbox. You can take a black motor with high speeds, and put adapters with large gears on it to raise the speed even more. The principle is like riding a bicycle.

[@spacetravelDEV]

Hi, i wanted to buy the 12V, 80RPM version of that motor. On the website i see a no load current of 0.3A just as your, a load current of 1.6A and a stall current of 6.5A. I was hesitating between using a 8A power supply or 10A power supply. Btw i want to use the motor with a load that's why i'm targeting for higher current ones. Can you help me to choose one or maybe something else?

[@Robotics_Robot]

Hi! Yes, the black motors have proven themselves well. I think they can be used in your projects. You just need to know what voltage you will have and what gearbox you need for the speed in the project. And you are done!

[@spacetravelDEV]

@@Robotics_Robot So at 12V an 8A power supply is enough?

[@Robotics_Robot]

@@spacetravelDEV Yes! That's enough for one engine.

[@moblu]

nice, how many nm?

[@Robotics_Robot]

I didn't understand the question. If you meant rpm, there are 12.

[@akeemgriffiths4459]

What are those little thing jn tiur hand?

[@Robotics_Robot]

Hello! It was a flexible coupling for fixing the central shaft of the engine! Sold with motors.

[@akeemgriffiths4459]

@@Robotics_Robot on Amazon?

[@Robotics_Robot]

@@akeemgriffiths4459 No. I bought motors on another electronics site.

[@coolkalangjack]

Hi may i ask how can i connect 3axis joystick potentiometer in dc motor with dc driver? i want to controll the reverse and forward with joystick, can you help me with the wiring diagram?thank you 🙂

[@Robotics_Robot]

Hello! What driver are you using? Or Arduino?

[@coolkalangjack]

Hi @@Robotics_Robot im only using pwm driver.

[@coolkalangjack]

can you help me with the wiring diagram of a joystick potentiometer to pwm dc motor speed controller

[@Robotics_Robot]

@@coolkalangjack If you want to connect to exactly the same driver as in the video. It's unlikely that you will succeed. The joystick has a potentiometer in the middle with the value set to the middle value. And the potentiometer has values ​​from 0 and above. The engine will start from the center position. If you do this on an Arduino, it can be removed programmatically. And if it’s the way you want, I don’t know. There, then the joystick needs to be disassembled and the springs removed so that it is from the zero position, and not the central one. And reverse will still work on the buttons. If I have time, I might make a video on this project. I will try.

[@Robotics_Robot]

@@coolkalangjack Ok.