Writing Your First LabVIEW FPGA Program

[@wenbinyang1689]

I think it's better to start with a blank project. I had a hard time reaching the starting point of this video.

[@NIGlobalYoutube]

The engineers in our forums should be able to answer this. Try posting your question here (forums dot ni dot com) and someone will get back to you quickly!

[@sonu0602]

Daq assistant is not supporting any device in compact CRIO 9036...can you tell me..why it is..

[@mondayikhide3101]

Thanks for the video.... very helpful. Please is it possible to export data stored in excel into labview and run it on the hardware like a real time event?

[@AlessandroDeLima-k3u]

Dear Vinita, do you have an exercise booklet for this course? I'm a Scientific Initiation student here in Brazil and I need to develop an FPGA application, using the cRIO9054 and some sensors and actuators, and I'm having difficulty finding a course that suits me. Thank you in advance!

[@NIGlobalYoutube]

Hi there, we’ve got you covered! This training is the perfect one for you bit.ly/3zk2nrT

[@teeshatanaaz8411]

Best thing I have ever seen

[@S-MKim]

Congraturations to your successful demonstration. It is good to know that you can use the FPGA hardware target as a real time ontroller: in your case, gain controls of 1 and -1. As a control engineer, I just wander if your target is fast enough to some control sound and vibration signals up to about 1 kHz. What is the sampling frequency inside the target? How high can you set?

[@brettb.5823]

Thanks for the question. I found another video on KZbin that Vineet did on "Measuring Loop Timing in LabVIEW FPGA" that you might be interested in. Most NI FPGA targets clock at 40 MHz. kzbin.info/www/bejne/n5nZXqp7iq6XZqc A couple of other thoughts. 1.) The limiting factor on control rate could be the code + FPGA or the module timing. NI's sound and vibration modules that support IEPE/ICP excitation sample up to 102.4 kS/s/ch. 2.) Using one of NI's modules with a SAR converter, like the NI 9215, with an accelerometer + external amplifier that outputs a 0-10V signal may be better for control because these modules (SAR modules like the 9215) - can be clocked by the FPGA loop whereas the IEPE/ICP sound and vibration modules use an internal clock. I could see a path to either working for 1kHz, it just depends on what else is going on and the demands of the control system. Hope this helps.

[@S-MKim]

@@brettb.5823 Thanks for your comment. I agree with your thoughts. By the way, I watched the video again and realized that Vineet demonstrated digital control, not analog control. Neverthess he could do the same with analog control.

[@johnpaulbounce3708]

How can I create a program where the voltage applied (or current) is constant while measuring current (or voltage) through time? We have an I-V tracer run by LAbView programming. I want to measure current (or current) through time while applying constant voltage (or current). But don't know the right program. Can I ask for help?

[@nasirdaneshiar6131]

hello , I want to know that is it possible to connect labview to FPGA without RIO board?

[@101picofarad]

No :) You must buy NI RIO (or PXI). But today NI says that LabView may export project as vivado project (for 7-series or newer xilinx chip). But i not see any alive engineer who use this.

[@electricalengineering4510]

Hello I have a problem in my project in LabVIEW which need FM Demodulation which the receiver is a super-heterodyne Can u help me ?

[@ahmadtarmimi7288]

post your question in ni.com forum

[@jaydevkalivarapu]

Can I know the order in which I need to view the videos in this playlist for better understanding as I am to LabVIEW FPGA programming...

[@IThinkForMe]

www.ni.com/tutorial/14532/en/ has the list of topics

[@freeflaminginfinite917]

Is labview available for free, also is there a Linux version available by any chance?

[@PreludeSon]

+FreeFlamingInfinite No, they're not free. I wish they make it free for student and hobbyist. That way, it'll increase the adoption rate.

[@freeflaminginfinite917]

InfinityOrchid Absolutely agreed.

[@hyeoklee0107]

Really thanks for the video!

[@ahmadtarmimi7288]

Very good explanation.. that why i strongly suggest use NI equipment or instrument and labVIEW platform..:), wondering why have 1 dislike...

[@bewbmike]

Where do they go over saving signals from the FPGA IOs?

[@kevinivandiazsolis]

Library? Toolkit?

[@NIGlobalYoutube]

Hi Kevin! LabVIEW FPGA is an add-on Module, you can learn more at www.ni.com/en-us/shop/software/products/labview-fpga-module.html and www.ni.com/en-us/shop/electronic-test-instrumentation/add-ons-for-electronic-test-and-instrumentation/what-is-labview-fpga-module.html. Please let us know if we can assist you further.

[@陳彥碩-t2x]

Thanks for the video!

[@NIGlobalYoutube]

You are welcome! Hope it helped.

[@jaydevkalivarapu]

*new to

[@Sajamalali-i2i]

SURJAMAALI❤😂🎉😢❤❤❤❤

[@Inventeeering]

LabVIEW WEMO Toolkit kzbin.info/www/bejne/rGe7ZYShjraHkLc