"Looking Through the Gap" TIG Welding Technique

[@luugo86]

This technique I have the most difficulty with, thank you for posting the video, great education as always!

[@abuwoodworth1463]

Thank you for the content,very informative and helpful

[@nathanielclause2588]

One of my favorites to pull out, especially on a tight bottom open top

[@v8-tres869]

I always learn from your videos and was wondering if you could possibly do a video on learning to weld with you non dominant hand this is what I struggle with the most.

[@X3MTIG]

I’ll put it on my list

[@Afghanxx]

amazing step up in production videography. amazing content for ppl, thank you

[@X3MTIG]

Much appreciated!

[@johnmoriarty6158]

Great video and well made. I look forward to every video. Thanks for sharing.

[@X3MTIG]

Awesome, thank you!

[@Donaldtrizz]

hello have been watching your videos for a while and have learned learned lots tips and tricks but do you think you could do a video on stainless pipe with "mud wire"?

[@X3MTIG]

Great suggestion!

[@khalidabouhassan5836]

Another great tutorial! 💪🏽

[@X3MTIG]

Thanks my friend 👍

[@januszcichanowski4024]

jak zawsze odcinek na wysokim poziomie

[@РусланВоробьёв-р7ц]

Hello XZM TIG colleague, I really liked your video, thank you for your work. I would like you to film in addition to this view or answer this question when welding a root through a gap, how and at what distance should the tungsten be and at what height do you hold the wire. Thanks in advance

[@shawnramey614]

How do you do this without dipping your tungsten? How can you see your tungsten with the wire in your field of vision

[@X3MTIG]

Little bit of experience involved 👍

[@OmarValadez-v8x]

Turn your heat up

[@bradshaw448]

Excellent 🦾, hello from Ireland

[@tonisiqueira9543]

Sim mestre e se a gente observar bem a posição do grau da tocha e material de adição se mantém a mesma formatizando essa bela raiz obrigado por mais esse belo vídeo 🇧🇷🙏

[@tata2692]

Nice video. My question is, are u using less amps doing that techniq, than when u are welding normally doing walk the cup?

[@X3MTIG]

I’m using same amperage

[@robertogutierrez2808]

Sube más vídeo Master te pierdes mucho con tus videos saludos....

[@X3MTIG]

Doing what I can

[@razorray7607]

Cool vid. ✌🔥

[@rolandsarins7151]

Are you using tacks in order to support wire while feeding it? I noticed you where using only lift tig most of time - why? How you avoid unplaned arc strikes on pipe? Do you have contactor switch on your torch? Some Esab machines have this option for lift tig does your Miller have it to?

[@X3MTIG]

I’m using both, lift and scratch start, no contactor switch available on my type of machine

[@rolandsarins7151]

@@X3MTIG thanks

[@omarvaladez8785]

Hey bro what do you use to sharpen your tungsten

[@X3MTIG]

Bench grinder if available if not angle grinder

[@dinoj8126]

Odličan video kao uvijek, znaš li možda po gdje po Hrvatskoj mogu rijesit atestiranje/certifikaciju/školovanje. Imam godinu i par mjeseci staža kao zavarivač ali teško pronalazim posao radi papira

[@X3MTIG]

Hvala ti, nebih ti mogao sa sigurnoscu reci tocno jer me nema u Hrvatskoj vec dugo vremena, ali znam da je to prije bilo moguce kroz neke kompanije koje su trazile argonce, npr. Monting i Montaza, da li je to jos uvijek tako, nebih znao!

[@dinoj8126]

@@X3MTIG E hvala na odgovoru, montig je opcija,i tamo cu ići ako ne nađem nigdi bliže, iz splita sam, ode je sve propalo sta se tiče industrije, a teško si mogu priustit otic u ZG 5 mjeseci na obuku, ali bojim se da ću morati. Hvala ti i nastavi nas poducavati sa ovim videima

[@nayanbarua9670]

Did you use filler ER 70s2 or ER 70s6,please say, I waiting for your reply.Very nice root penetration, lot of thanks 🌹🌹🌹

[@X3MTIG]

80S-D2

[@nayanbarua9670]

Thanks sir for comment 🙏

[@brianbeaubien7371]

❤beautiful ❤

[@X3MTIG]

Thank you! Cheers!

[@людкиублюдки]

What lens do you use i can't do it with mines it flashes on me all the time :(

[@JoseTorres-tw7he]

weldtube auto lens and tefuawe, both auto darkening lenses that ive used for tig haven't had no issues

[@ttsupra87]

So slick

[@saviourtoesae4607]

How do you control your supply from supplying from the back what's your secret

[@danieldiaz2338]

when I start on the bottom my root comes out flat even when back feeding what causes that ?

[@jonathansanchez2169]

When I was first learning they told me to over exaggerate the feeding it worked for me hope it works for you

[@sreenathas0597]

Sir how much current.... Root face? And how much gas?filler s2 or s6?

[@sreenathas0597]

Sir pls reply me plsssssss

[@sreenathas0597]

Root gap how much

[@X3MTIG]

120 amps

[@JoseJimenez-kt1rv]

What kind of wire is it

[@X3MTIG]

80s-D2

[@daveharringbone8512]

Cup size and tungsten length

[@X3MTIG]

Cup #8 , tungsten 1/8