Xiaomi Dreame D9 "laser sensor error" LSD fault - Fixed 👍

[@dolltrees.3663]

Hey that procedure worked for me ...now my robot is working as usual..thank you..

[@kristopherkruska8917]

Awesome fix. Without this video I'd never tried to repair this issue myself and would've gone through the whole returning-process. There was just a hair wrapped around the rubber band that irritated the workflow. Now all is fine again (dreame D9)

[@JulyGotchkov]

Many thanks for this video, Duc! Thanks to it I've fixed my L10Pro and now LSD is working again :)

[@-semyonlaskin]

Fixed. Thanks!

[@zingirable]

Thank you. Repeated it and started working

[@m4z3h4z3]

Big THX 2 you. Easy fix for my L10Pro.

[@dhingue]

Thank you so much! It worked for me!

[@antruong7284]

Hay lắm, tôi đã làm theo và sửa được lỗi. Cám ơn nhiều.

[@jimmylau84]

My D9 also having issue. 1. The mapping sequence is way off now (not doing the normal sequence where it cleans the border from right to left then zig-zag to cover open areas) 2. The mapping in the app (the white lines) also is way off now. Very minimal lines shown despite it already covered more areas) 3. Frequently doing the reverse motion in high velocity and thus hard bang on it’s back, persistently

[@George-kj6bm]

Exact same on my L10 Pro

[@7raiton7]

Did You fix this problem? I've similiar issue with mine D9, it's not mapping correctly and half time drives backward or just hits obstacles at full speed

[@SnejanaIvanova-c4p]

Thank you, your video helped me!

[@Ewert99]

Thanks! worked for me

[@slaughterboy99]

Thank you! You help me a lot.

[@cmf343]

THANK YOU

[@heikoschmidt9713]

Thanks man!

[@haninzwen-ks4ie]

Thank you!!

[@TanNguyen-sr5ns]

Em đang dùng con D9 này mà nó k kết nối đc với đt, anh có biết là lỗi gì k ạ

[@minhducthach]

Từ lúc mua về đã ko kết nối đc với mihome à b? B thử giữ nút reset trên máy để trả hết về mặc định xem, vì có thể ng bán đã từng kết nối với mihome khác nên máy sẽ ko cho kết nối với máy của bạn

[@TanNguyen-sr5ns]

Thanks bác đã trả lời. Trước mua về e có kết nối đc với đt bình thường. E đã reset rồi, đèn wifi trên robot có nháy chậm nhưng vào đt thì wifi k tìm thấy robot.

[@minhducthach]

@@TanNguyen-sr5ns b đã cập nhật firmware của máy & mihome bản mới chưa? để mai ở nhà m thử reset xong cài lại xem ntn mình báo nhé

[@hikvisionipcam4124]

I need a way to contact you. I have the same glitch, but a little different

[@boyan056]

Thanks you So much!

[@tuftufthemagic]

Works also for l10 pro

[@minhducthach]

Thanks for your cmt

[@user-qz3rf4kd5c]

It worked! Thank you!!! Greetings from Germany :)

[@minhdng0904]

Thanks you! It just works! There is a tiny hair strain stuck inside the housing that makes the radar could not turn. Just disassemble them all and clean the rotor and now everything is working again!

[@philipphache8467]

Worked perfectly for me thank you! Greetings from Germany

[@worldlyconcerns]

Thank you so much. This helped me open up and clean my Dreame Z10 Pro, and even though I didn't see any dirt or hair that might have caused the laser to stop working, the issue was fixed! Hugely appreciated.

[@unmecsuryoutube7413]

My robot stopped working properly... It was just a damn hair in front of one sensor. Make sure to clean every sensor with some air or a soft brush before disassembling anything :)

[@kadimski7610]

This video helped me resolving my issue with my Dreame z10 pro. The laser sometimes got stuck and under the laser sensor there was a loose screw! Thanks for the video.

[@BrianBoucher85]

My Laser didn’t work. So i tried it like you did. There was nothing wrong but it works now! So thanks 🙏🏼😅

[@shyamvk]

You are a lifesaver my friend!!! Thank you!!

[@rubaal-sharifi8464]

I followed the same steps but it still doesn't work. Any other suggestions, please?

[@RetroAsiaChannel]

Lifesaver video, thanks for showing this!

[@philipmuller3951]

Verry helpfull

[@elchinator]

That was helpful, thank you!

[@GurgenAvagyan]

This truly helpful!! Thank you.

[@PopescuEugen-wz8fg]

you seem to be very good at this my cleaning robot has a problem with the front impact sensor any idea how to fix this?

[@ernstfast6449]

Worked

[@INSIDEOFT]

Thanks! Had some hair that had gotten stuck and this solved the issue.

[@AgnèsPeltier-o6b]

super efficace! bravo et merci 👍

[@dansdalklc66]

Teşekkürler

[@sauftrag1442]

Thank You!

[@dubwisee5724]

Manu thanks dude.