XL Power 520 Flight - Tail not what i hoped for :(

Tail servo , Align DS535 Mini Metal Geared Digital Tail Servo HSD53502T
Align 90mm Carbon Fiber Tail Blade HQ0900C
Cyclic, Align DS530 Mini Digital Servo HSD53002T X 3
MICROBEAST Plus Flybarless - V5.0
Single DSMX Satellite
XLPower 4020 Brushless Motor
HOBBYWING platinum 120A V4 ESC
Overlander 3350mAh 22.2V 6S 35C Supersport Pro LiPo Battery
Pitch Curve Nor, 42% 46% 50% 75% 100%
Idle 1 82% 82% 82% 82% 82%
Gyro Gain 33%
Pitch, -12 +12
1.HPS (High Precision Head System), New head with 2-piece blade grip preserves grips in the event of a crash.
2.To improve the strength and durability of the 10mm high strength steel main shaft,8mm high strength steel spindle shaft,M5 YFS high strength spindle shaft screw. New head with 2-piece.Blade and support 3-4mm aperture,rotor blades compatible size 430mm 470mm 480mm 500mm 515mm 520mm.
3.Brand new CNC metal reinforcement plate effectively increase the torsional strength of main frame, under extreme 3D maneuver, you can strongly feel its solid reinforcement from its structure.
4.Swash-plate servos support medium-sizes servo,the XLPOWER520 lightweight design is 1800g,without battery this effectively increase the power and improves flight time,Tail servo support medium-sizes servos and standard servo，motor support 4020 or 4025.1100KV for 6s,550kv for 12s.Li-Po support 6S 3000Mah-5200mAh.Battery slot H 55mm*W 48mm*L150mm.ESC support 80A-120A.
5.The canopy manufactured with durable lightweight fiber material, the Landing skid is tilted 2.5 degree forward which improves crash worthiness.
SPECIFICATIONS:
Lenght: 981mm
Height: 120mm
Width: 310mm
Main blade size: 425mm - 520mm
Tail blade size: 72mm - 86mm
Motor pinion: 12t included;13t optional
Helical CNC Main gear: 106t
Tail pinion: 13T
Autorotation gear: 60T
Main to tail gear ratio: 4.615
RTF weight: 2400g-2700g
Main shaft diameter: 10mm
Feathering shaft diameter: 8mm
Tail boom diamater: 20mm
Max battery size: 150mm*48mm*55mm(6s)
Includes:
(1) XLPower 520Kit
(1) XLPower 4020 Brushless Motor
(1)HOBBYWING platinum 120A V4 ESC
(1) Set of RotorTech Blades 520mm Rotor Blades
(1) Set of XLPower80mm Carbon Tail Rotor Blades
(1) Foam Blade Holder
Needed to Complete:
Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
(1) 6S Li-Po 3000 ~ 5200mAh
(1) Digital Pitch Gauge
(3) Mini Size Cyclic Servos
(1) Full Size Tail Servo
Misc. Building Equipment

[@33gate1]

If i had a full size servo and a different flybarless unit i would troubleshoot but i do not have a full size servo or a different flybarless unit :(

[@arcturus8218]

nice flight . mine all kick a bit i use microbeast i did try the parameter menu pre torque compensation but didnt do much higher head spead sometimes helps , im no expert on setup there seems to be other giros that may be better but these are easy so i like them .my new oxy 4 on 4s doin tick toks kept kickin out big time so i went to 5 s for a bit more power and havnt had the same issue yet .

[@33gate1]

@@arcturus8218 Thanks for your input, yes the Microbeast is so nice setting up, my Trex 550X with Microbeast has 0 kick on pitch pump and flying 3d, rock solid tail on my 550X.

[@v4zzy219]

It's definitely not the heli. Gyro gain of 33% on the beast is very low for this heli. Do some hurricanes or funnels or something to stress the tail out hard. keep raising gyro till you get violent wag, then back off a touch. What collective precomp setting are you using in the beast? What tail rate consistency setting are you using in the beast? Are you using the middle hole on stock servo arm for tail? Definitely invest in a full size tail servo when u can.

[@33gate1]

Hi, i was getting tail wag at 40%, i always start at 40%. Using the standart 4 arm servo arm, the 3rd hole so 13mm from centre bolt to centre hole. I just cheched my Torque precomp now, i think it was set up wrong, when at mid stick and i give possitive pitch the tail would precomp in the wrong direction, the slider would move to the right when standing behind the heli. Had it on red solid, moved it to blue solid and the slider now moves to the left. Will give that a go tomorrow and give you a update.

[@v4zzy219]

@@33gate1 sounds good man. Everything will work out! 👍

[@33gate1]

@@v4zzy219 Setting up the Torque precompensation in the MicroBeast correct solved my tail problems :)

[@v4zzy219]

@@33gate1 sweet bro, I'm glad!